Search
Search Results
-
Morphology Microstructure and Mechanical Properties of Fe25/WC/TiC Coating and Abrasive Wear Properties Under Dry/Wet Sand Conditions
To address the issue of low surface hardness and poor wear resistance of 45# steel, this study applied laser cladding technology to prepare three...
-
Microstructure Evolution and Formation of Dual-Phase AlCoCrFeNiSi0.5 High-Entropy Alloy Powders by Mechanical Alloying
Dual-phase AlCoCrFeNiSi 0.5 high-entropy alloy powders for thermal spraying were prepared by mechanical alloying (MA). The effect of ball-milling time...
-
Martensite Formation and Dynamic Recrystallization in Cold Sprayed SS304L
In this study, a comprehensive set of characterization techniques are employed to demonstrate that the cold spray deposition process can result in a...
-
Debonding of Porous Coating: A Late Failure Mode of Uncemented, Partially Threaded Acetabular Components—Retrieval Analysis
Titanium plasma-sprayed (TPS) porous coatings have been used in total hip arthroplasty for decades. They are considered reliable, and very few...
-
Impact of the Rare Earth Element La on the Microstructure and Mechanical Properties of the Al/Steel Bimetallic Composite Interface Fabricated by Liquid–Solid Casting
This research aimed to explore the influence of the rare-earth element La on the interface microstructure and mechanical properties of Al/steel...
-
Improved Multi-Directional Forging Process and Its Effect on Microstructure and Three-Directional Mechanical Properties of 2195 Al-Li Alloy
Reticular crystal phases and abnormally coarse grains are key problems that restrict the improvement of the mechanical properties and uniformity of...
-
Microstructure and Wear Resistance of a Ni–Fe–Si–B Amorphous Composite Coating by Laser Cladding
In this study, a Ni–Fe–Si–B amorphous composite coating is coated on H13 steel by laser cladding. Coatings are systematically investigated for their...
-
Influence of Dynamic Precipitation of γ′ Phase on Dynamic Strain Aging in a Fe-Ni-Based Superalloy
Discontinuous plastic flow due to dynamic strain aging (DSA) in a Fe-Ni-based superalloy was investigated by tensile tests in the temperature range...
-
A Review on Wire Arc Additive Manufacturing of Magnesium Alloys: Wire Preparation, Defects and Properties
Wire arc additive manufacturing (WAAM) is widely used in the rapid prototy** of large parts because of its high deposition rate, high material...
-
Aerosol Deposition of CuFeO2 Photocathode Coatings for Hydrogen Production
Photoelectrochemical (PEC) water splitting is a viable route for green hydrogen generation. In PEC cells, the electrodes are coated with suitable...
-
Microstructure and Tribological Behavior of Low-Temperature HVAF Ti6Al4V Coatings
Ti-6Al-4 V is commonly used in gas turbine engines and is sometimes subject to wear during operation. To address this, cost-effective and...
-
Effect of Pre-Deformation on Precipitation in Al–Zn–Mg–Cu Alloy
In this work, strengthening effects and evolution of precipitates in a pre-deformed Al–Zn–Mg–Cu alloy during ageing were investigated using Vickers...
-
Impact of Laser Shock Peening on Mechanical Properties of Wire Arc Additive Manufactured Grade 91 Steel and Monel-400 Bimetallic Components
This study investigates the effects of Laser Shock Peening (LSP) on the mechanical properties and microstructure of Wire Arc Additive Manufactured...
-
Effect of Nb on Microstructure and Wear Property of Laser Cladding CoCrFeNiTiNbx High-Entropy Alloys Coatings
A group of CoCrFeNiTiNb x high entropy alloys (HEAs) coatings were produced by laser cladding. The effect of Nb content on the microstructure and wear...
-
Measurements of Enthalpies of Mixing of Sn–Ga–In Ternary Alloy System by Calorimetric Technique
The ultimate objective of this study is to find a way to replace toxic lead-based solder with a non-toxic replacement that retains all of the...
-
-
Microscopic Study on the Blister Formation Mechanism in Electrogalvanized Steel
The blister formation mechanism in electrogalvanized steel was studied by analyzing the blister’s internal structure. Electrochemical hydrogen...
-
Effect of Nb on Austenite Grain Growth in 10Cr-3Co-2W Martensitic Heat-Resistant Steel
AbstractThe effect of Nb on austenite grain growth kinetics was investigated in 10Cr-3Co-2W martensitic heat-resistant steel under various tempering...
-
Effect of Oxygen Injections on the Porosity of High Pressure Die Castings
This study aims to investigate the role of oxygen in optimizing the Pore-Free Die Casting (PFDC) process to enhance the quality of aluminum castings...
