Search

Search Results

1. A deoxidation thermodynamic model for 304 stainless steel considering multiple-components coupled reactions

   A thermodynamic model for predicting the equilibrium oxygens of 304 stainless steel was developed based on the theory of slag–steel equilibrium, the...

   Yan Yan, Guang-hao Shang, ... Han-jie Guo in Journal of Iron and Steel Research International

   Article 09 October 2023
   

2. Powder bed fusion of high-Mn-N Ni-free austenitic stainless steel: achieving low porosity and high mechanical strength through process parameter selection

   The emergence of innovative high-performance stainless steels is essential at the forefront of material science. This research highlights the...

   Leandro Akira Tochiro, André Henrique Guimarães Gabriel, ... Mohammad Masoumi in The International Journal of Advanced Manufacturing Technology

   Article Open access 08 February 2024
   

3. Effect of Induced Martensite Content on Microstructure Evolution and Mechanical Properties of Ferritic Stainless Steel

   Due to the ferrite–austenite dual phase at high temperature, the hard martensite phase was introduced into 430 ferritic stainless steel (430 FSS) by...

   Pengguang Ma, Guoqing Zu, ... Ying Han in JOM

   Article 05 December 2023
   

4. Effect of Ultrasonic Burnishing Parameters on Burnished-Surface Quality of Stainless Steel After Heat Treatment

   Ultrasonic burnishing induces beneficial compressive stresses and high surface quality in components with contact as a functional requirement. It was...

   Rizwan Ullah, Eric Fangnon, Juha Huuki in Flexible Automation and Intelligent Manufacturing: The Human-Data-Technology Nexus

   Conference paper Open access 2023
   

5. Chemistry and microstructure of duplex stainless steel powders from recycled Z100 mixed with 316L steels

   Recovered metallic waste can be used in additive manufacturing as a feedstock if the subsequent steps of the waste-to-product process are...

   Filip Kateusz, Adelajda Polkowska, ... Jerzy Jedliński in Archives of Civil and Mechanical Engineering

   Article Open access 11 October 2023
   

6. Microstructure and tribological properties of Stellite 12 coating by laser cladding on 304 stainless steel surface

   In the present study, the Stellite 12 coating was prepared on 304 stainless steel using laser cladding technology. The phase composition,...

   Rui Wang, Changyao Ouyang, ... Qiaofeng Bai in Journal of Mechanical Science and Technology

   Article 02 August 2023

7. Steel Products

   Steel can be produced in different grades in adaptation to the particular building task it is supposed to fulfill. This can be achieved by means of...

   José Luis Moro in Building-Construction Design - From Principle to Detail

   Chapter 2024
   

8. Effect of microstructure variation on corrosion properties of as-cast 0Cr23Ni13 stainless steel at high strain rate of hot compression

   The optimization of hot compression technique of as-cast 0Cr23Ni13 stainless steel at high strain rate was discussed, and its corrosion resistance...

   Jun-chen Li, Meng-yuan Ye, ... **ng-run Chen in Journal of Iron and Steel Research International

   Article 22 March 2023
   

9. Effect of slag composition on kinetic behavior of deep deoxidation of 5 wt.% Si high-silicon austenitic stainless steel

   Based on a thermodynamic study of 5 wt.% Si high-silicon austenitic stainless steel (SS-5Si) smelting using CaF ₂ –CaO–Al ₂ O ₃ –MgO–SiO ₂ slag to obtain a...

   Guan-xiong Dou, Han-jie Guo, ... Qing-yun Chen in Journal of Iron and Steel Research International

   Article 09 July 2024
   

10. Laser beam remelting of stainless steel plate for cladding and comparison with conventional CMT process

    Progressing towards circular economy requires smarter and more efficient use of energy and resources. Laser beam can be efficient and flexible tool...

    Ivan Bunaziv, **aobo Ren, ... Sverre Gulbrandsen-Dahl in The International Journal of Advanced Manufacturing Technology

    Article Open access 22 May 2023
    

11. Pitting corrosion initiated by SiO₂–MnO–Cr₂O₃–Al₂O₃-based inclusions in a 304 stainless steel

    The influence of the aluminum content on the pitting corrosion of a 304 stainless steel by a Cl ⁻ solution was investigated. The number, area, and...

    **-zhen Hu, Shi Li, ... Li-feng Zhang in Journal of Iron and Steel Research International

    Article 04 October 2023
    

12. Mechanical performance of 22SiMn2TiB steel welded with low-transformation-temperature filler wire and stainless steel filler wire

    TX-80 low-transformation-temperature (LTT) welding wire was used to replace the traditional ER 307Si welding wire to realize the connection of...

    Zi-dong Lin, Kai-jie Song, ... **ng-hua Yu in Journal of Iron and Steel Research International

    Article 30 October 2023
    

13. Partitioning of nitrogen atoms and its effect on retained austenite content in an ultra-low-carbon Cr–Mn–N stainless steel

    The partitioning of nitrogen atoms and its effect on the retained austenite content (RAC) during quenching and partitioning (Q&P) process were...

    Zhe Zhu, Wan-tang Fu, ... Shu-hua Sun in Journal of Iron and Steel Research International

    Article 24 February 2021
    

14. Strengthening and precipitation hardening mechanisms of surface-mechanically treated 17-4PH stainless steel

    Achieving ultra-high strength without sacrificing too much ductility is the focus of attention in nanostructured materials. Here, the strengthening...

    Temitope Olumide Olugbade, Bankole I. Oladapo, ... Tin Tin Ting in The International Journal of Advanced Manufacturing Technology

    Article Open access 06 May 2024
    

15. Comparative Studies of Mechanical Properties and Microstructure of LPBF-Fabricated Virgin and Reused 316L Stainless Steel

    The investigation of the various properties of components manufactured with Additive Manufacturing (AM) - methods is important to realize the...

    Wakshum Mekonnen Tucho, Ole Kristian Bjørge, ... Vidar F. Hansen in Analytical and Experimental Methods in Mechanical and Civil Engineering

    Conference paper 2024
    

16. Design and analysis of structure for milling OCr13 stainless steel with unequal tooth pitch plunge milling tool

    Structural design of unequal pitch step plunge milling tool. According to the theoretical analysis of the primary tool parameters, the structure of...

    Junhua Li, Yu Wang, ... Lulu Jiang in The International Journal of Advanced Manufacturing Technology

    Article 23 August 2023
    

17. Multicriteria optimization of the weld characteristics of keyhole plasma arc welding on super austenitic stainless steel: a mathematical approach

    The superaustenitic stainless steel AISI 304HCu tubes, preferable in crucial parts like reheater and superheater panels of Advanced Ultra-Super...

    P. G. Sam Infant Jones, S. Rajakumar, ... V. Balasubramanian in International Journal on Interactive Design and Manufacturing (IJIDeM)

    Article 04 January 2023
    

18. Machinability investigation of 254 SMO super austenitic stainless steel in end milling under different cutting and lubri-cooling conditions

    The application of super austenitic stainless steels (SASS) in the petroleum, chemical, and naval industries has gradually increased owing to their...

    Émerson S. Passari, André J. Souza, Carlos A. G. Aita in The International Journal of Advanced Manufacturing Technology

    Article 06 March 2024
    

19. Strength-Toughness Improvement of 15-5PH Stainless Steel by Double Aging Treatment

    To obtain better strength-toughness balance of 15-5PH stainless steel, a double aging treatment is proposed to investigate the mechanical properties...

    Rigele Te, Yutuo Zhang in Journal of Shanghai Jiaotong University (Science)

    Article 28 November 2021

20. Microstructure and texture evolutions of 310S austenitic stainless steel after cryogenic rolling and subsequent annealing: X-ray and electron backscatter diffraction studies

    The present work aims to study the microstructure and texture evolutions of thermomechanically processed 310S austenitic stainless steel. The...

    R. B. Heidari, M. Eskandari, M. Yeganeh in Journal of Central South University

    Article 01 March 2023