Skip to main content

23 Result(s)

within M. Kraini Remove this filter

previous disabled Page of 2
and

  1. No Access

    Article

    Impact of substrate temperature on structural, morphological and optical properties of In2S3 thin films deposited on ITO/glass substrate by spray pyrolysis technique

    In2S3 thin films were grown on indium tin oxide-coated glass substrates by a chemical spray pyrolysis technique at different substrate temperatures (300 °C, 360 °C, 400 °C and 460 °C). Structural analysis of the ...

    J. Koaib, I. Halidou, M. Kraini, N. Bouguila… in Indian Journal of Physics (2023)

  2. No Access

    Article

    Investigation of some physical and photoconductive properties of sprayed CuS2 film

    Copper sulfide (CuS2) has been prepared by spray pyrolysis process. Structural and morphological properties of prepared sample were investigated by XRD and AFM. The X-ray diffraction showed that the structure of ...

    N. Bouguila, Y. Bchiri, M. Kraini… in Journal of Materials Science: Materials in… (2022)

  3. No Access

    Article

    S/In molar ratio effect on the photoconductivity of the sprayed β-In2S3 thin films

    In2S3 thin films have been deposited onto glass substrates at 340 °C using an inexpensive spray pyrolysis method (CSP) via the reaction between high purity indium chloride and thiourea. Structural, optical and ph...

    Y. Bchiri, R. Souissi, B. Bouricha… in Journal of Materials Science: Materials in… (2021)

  4. No Access

    Article

    Electrical Behavior and Photocatalytic Activity of Ag-Doped In2S3 Thin Films

    Indium sulfide thin films with different amounts of silver do** were deposited by spray pyrolysis. The samples were tested as potential photocatalysts by degrading methylene blue (MB) dye aqueous solution un...

    B. Tiss, A. Ben Fradj, N. Bouguila, D. Cristea… in Journal of Electronic Materials (2021)

  5. No Access

    Article

    Influence of silver do** on physical properties of sprayed In2S3 films for solar cells application

    A set of silver-doped indium sulphide (In2S3:Ag) thin films were deposited by spray pyrolysis technique, at 350 °C, to analyze the effects of the Ag do** on the physical properties of the films. Within the limi...

    B. Tiss, Y. Moualhi, N. Bouguila, M. Erouel… in Journal of Materials Science: Materials in… (2021)

  6. No Access

    Article

    Impact of thermal annealing inducing oxidation process on the crystalline powder of In2S3

    Inorganic two-dimensional semiconductor indium sulfide (In2S3) has recently attracted considerable attention as a buffer material in the field of thin-film photovoltaics, photo electrochemical cells and other ene...

    A. Timoumi, W. Zayoud, A. Sharma, M. Kraini… in Journal of Materials Science: Materials in… (2020)

  7. No Access

    Article

    Substrate temperature effect on microstructure, oxygen adsorption and ethanol sensing response of sprayed In2S3 films

    This paper reports the effect of the substrate temperature of sprayed In2S3 material on the sensing response to ethanol. Glass substrates have been the supports of In2S3 thin films elaborated by spray pyrolysis t...

    R. Souissi, N. Bouguila, M. Kraini… in Journal of Materials Science: Materials in… (2019)

  8. No Access

    Article

    Effect of Seed Layer and Thermal Annealing on Structural and Optical Properties of Silicon Layers Deposited by PECVD

    Hydrogenated silicon (Si:H) layers have been deposited on crystalline silicon substrate by radiofrequency plasma-enhanced chemical vapor deposition technique (rf-PECVD) from SiH4/H2 gas mixture using different de...

    N. K. Maaloul, M. Kraini, K. Khirouni, H. Khemakhem in Journal of Electronic Materials (2019)

  9. No Access

    Article

    Impact of the annealing time on physical properties of sprayed In2S3 thin films

    Indium sulfide thin films were deposited on preheated soda-lime glass substrates using spray technique over experiment optimum conditions (Ts = 340 °C, S/In = 2). The effect of annealing time on structural, morph...

    N. Bouguila, M. Kraini, A. Timoumi, J. Koaib… in Journal of Materials Science: Materials in… (2019)

  10. No Access

    Article

    Nickel do** effect on properties of sprayed In2S3 films

    Nickel doped In2S3 films have been prepared by the chemical spray pyrolysis technique at 350 °C on glass substrates. The Ni do** level was changed by varying Ni:In molar ratio from 0 to 4% in solution. The stru...

    M. Kraini, N. Bouguila, J. El Ghoul in Indian Journal of Physics (2018)

  11. No Access

    Article

    The effects of do** type on structural and electrical properties of silicon nanocrystals layers grown by plasma enhanced chemical vapor deposition

    The purpose of this paper is to compare the influence of boron and phosphor do** on the optical, structural and electrical properties of hydrogenated amorphous silicon (a-Si:H) thin films elaborated at low r...

    M. Khelil, S. Kraiem, M. Kraini… in Journal of Materials Science: Materials in… (2018)

  12. No Access

    Article

    Properties of nickel doped In2S3 thin films deposited by spray pyrolysis technique

    In this work, nickel (Ni) doped indium sulfide (In2S3) films have been prepared by the spray pyrolysis (CSP) technique on glass substrates at 350 °C. The Ni do** level was changed with Ni:In (0, 2 and 4% in sol...

    M. Kraini, N. Bouguila, N. Moutia… in Journal of Materials Science: Materials in… (2018)

  13. No Access

    Article

    Some physical investigations on In2S3:Sn sprayed thin film

    Tin doped In2S3 film was grown by chemical spray pyrolysis method using compressed air as a carrier gas. Structural, morphological, optical and electrical properties of film have been investigated. X-ray diffract...

    M. Kraini, N. Bouguila, A. Bettaibi… in Journal of Materials Science: Materials in… (2016)

  14. No Access

    Article

    Experiments on In2S3:Sn Thin Films with up to 1% Tin Content

    Tin-doped indium sulfide (In2S3:Sn) thin films with different Sn:In molar ratios (0% to 1% by mol in solution) have been deposited on glass substrates by a chemical spray pyrolysis method. The films were investi...

    M. Kraini, N. Bouguila, J. Koaib, C. Vázquez-Vázquez… in Journal of Electronic Materials (2016)

  15. No Access

    Article

    Effect of vacuum annealing temperature on structural, morphological and optical properties of In2S3:Zn films deposited by spray pyrolysis

    Zinc-doped In2S3 thin films have been deposited by spray pyrolysis method at 350 °C on glass substrates with ITO contacts. The samples were sealed under vacuum (10−3 Torr) into a Pyrex tube and then annealed for ...

    J. Koaib, N. Bouguila, M. Kraini, A. Mhamdi… in Journal of Materials Science: Materials in… (2016)

  16. No Access

    Article

    Thickness Effect on Properties of Sprayed In2S3 Films for Photovoltaic Applications

    Indium sulfide (In2S3) films have been deposited on soda-lime glass substrates using a spray technique (CSP). Indium chloride and thiourea were used as precursors at a molar ratio of S:In = 2. The substrate tempe...

    N. Bouguila, M. Kraini, I. Halidou, E. Lacaze… in Journal of Electronic Materials (2016)

  17. No Access

    Article

    Structural, morphological and optical properties of annealed ZnS thin films deposited by spray technique

    ZnS thin films were deposited on glass slides by spray pyrolysis technique. The starting solution is a mixture of zinc chloride and thiourea. The substrate temperature was fixed at 350 °C. The films were then ...

    N. Bouguila, D. Bchiri, M. Kraini… in Journal of Materials Science: Materials in… (2015)

  18. No Access

    Article

    Investigation of the Physical Properties of Sprayed Nanocrystalline In2S3 Films

    In2S3 films have been grown on preheated glass substrate by spray pyrolysis. Indium chloride and thiourea in the molar ratio S:In = 2 were used as reagents. Substrate temperature was fixed at 613 K. These films a...

    N. Bouguila, M. Kraini, I. Najeh, I. Halidou, E. Lacaze… in Journal of Electronic Materials (2015)

  19. No Access

    Article

    Substrate temperature effect on properties of sprayed In2S3 films

    In2S3 films have been grown on glass substrates by spray pyrolysis technique. The deposition was carried out in a 300–500 °C substrate temperature and the molar ratio S/In is fixed to 2. The characteristics of th...

    N. Bouguila, M. Kraini, A. Timoumi… in Journal of Materials Science: Materials in… (2015)

  20. No Access

    Article

    Influence of annealing temperature on the properties of In2S3:Sn films deposited by spray pyrolysis

    Tin-doped In2S3 films were grown by the chemical spray pyrolysis method using compressed air as a carrier gas. The films were annealed for 2 h at different temperatures (300, 400 and 500 °C) under nitrogen atmosp...

    M. Kraini, N. Bouguila, J. El Ghoul… in Journal of Materials Science: Materials in… (2015)

previous disabled Page of 2