Abstract
High Velocity Oxy-Fuel (HVOF) has the potential to produce hydroxyapatite (HA; Bio-ceramic) coatings based on its experience with other sprayed ceramic materials. This technique should offer mechanical and biological results comparable to other thermal spraying processes, such as atmospheric plasma thermal spray, currently FDA approved for HA deposition. Deposition of HA via HVOF is a new venture especially using the Sulzer Metco Diamond Jet (DJ) process, and the aim of this article was to establish this technique's potential in providing superior HA coating results compared to the FDA-approved plasma spray technique. In this research, a Design of Experiment (DOE) model was developed to optimize the Sulzer Metco DJ HVOF process for the deposition of HA. In order to select suitable ranges for the production of HA coatings, the parameters were first investigated. Five parameters (factors) were researched over two levels namely: oxygen flow rate, propylene flow rate, air flow rate, spray distance, and powder flow rate. Coating crystallinity and purity were measured at the surface of each sample as the responses to the factors used. The research showed that propylene, air flow rate, spray distance, and powder feed rate had the largest effect on the responses, and the study aimed to find the preferred optimized settings to achieve high crystallinity and purity of percentages of up to 95%. This research found crystallinity and purity values of 93.8 and 99.8%, respectively, for a set of HVOF parameters which showed improvement compared to the crystallinity and purity values of 87.6 and 99.4%, respectively, found using the FDA-approved Sulzer Metco Atmospheric Plasma thermal spray process. Hence, a new technique for HA deposition now exists using the DJ HVOF facility; however, other mechanical and biorelated properties must also be assessed.
Similar content being viewed by others
References
J. Stokes and L. Looney, Residual Stress in HVOF Thermally Sprayed Thick Deposits, J. Surf. Coat. Technol., 2004, 177-178, p 18-23
T.J. Levingstone, “Optimisation of Plasma Sprayed Hydroxyapatite Coatings,” Ph.D. thesis, Dublin City University, Ireland, 2008, http://doras.dcu.ie/579/
P. Fauchais, Understanding Plasma Spraying, J. Phys. D Appl. Phys., 2004, 37, p R86
H.C. Gledhill, I.G. Turner, and C. Doyle, In Vitro Dissolution Behaviour of Two Morphologically Different Thermally Sprayed Hydroxyapatite Coatings, Biomaterials, 2001, 22, p 695-700
H.C. Gledhill, I.G. Turner, and C. Doyle, In Vitro Fatigue Behaviour of Vacuum Plasma, Detonation Gun Sprayed Hydroxyapatite Coatings, Biomaterials, 2001, 22, p 1233-1240
H.C. Gledhill, I.G. Turner, and C. Doyle, Direct Morphological Comparison of Vacuum Plasma Sprayed, Detonation Gun Sprayed Hydroxyapatite Coatings for Orthopaedic Applications, Biomaterials, 1999, 20, p 315-322
T.J. Levingstone, Ceramics for Medical Applications, Dublin City University, Ireland, 2008, ISBN: 1-87232-752-4
S.J. Schneider, Jr., Ceramics and Glasses, Vol 4, ASM International, Ohio, USA, 1991, ISBN 13: 978-0-87170-282-1
P. Ducheyne, J. Beight, J. Cuckler, B. Evans, and S. Radin, Effect of Calcium Phosphate Coating Characteristics on Early Post-Operative Bone Tissue Ingrowth, Biomaterials, 1990, 11, p 531-540
K. Soballe, The role of H-A-C in ingrowth prostheses, Hydroxyapatite Ceramic, a Decade of Experience in Hip Arthroplasty, the Proceedings of a Two Day Symposium, R. Furlong, Ed., Held at the Royal College of Surgeons of England on Thursday 2nd & Friday 3rd November 1995, Furlong Research Foundation, London, 1996, p 57-67
ASTM F1185-03, Standard Specification for Composition of Ceramic Hydroxyapatite for Surgical Implants, ASTM F1185-03, ASTM International, 2003
K.A. Gross, K. Heeman, and K.S. Saber-Samandari, Evaluation of Commercial Implants with Nanoindentation Defines Future Development Needs for Hydroxyapatite Coatings, J. Biomed. Mater. Res.: Appl. Biomater., 2010, 93B(1), p 1-8
Anonymous, Implants for Surgery-Hydroxyapatite. Part 2: Coatings of Hydroxyapatite, BS ISO 13779-2:2000, 2000
Y.C. Tsui, C. Doyle, and T.W. Clyne, Plasma Sprayed Hydroxyapatite Coatings on Titanium Substrates Part 2: Optimisation of Coating Properties, Biomaterials, 1998, 19(11), p 2031-2043
L. Sun, C.C. Berndt, and C.P. Grey, Phase, Structural, Microstructural Investigations of Plasma Sprayed Hydroxyapatite Coatings, Mater. Sci. Eng. A, 2003, 360(11/15), p 70-84
M.F. Morks and A. Kobayashi, Effect of Gun Current on the Microstructure, Crystallinity of Plasma Sprayed Hydroxyapatite Coatings, Appl. Surf. Sci., 2007, 253(17), p 7136-7142
M.P. Taylor, “Assessment of Plasma-Sprayed Hydroxyapatite Coatings,” Ph.D. thesis, University of Birmingham, Birmingham, 1994
P. Cheang and K.A. Khor, Thermal Spraying of Hydroxyapatite (HA) Coatings: Effects of Powder Feedstock, J. Mater. Process. Technol., 1995, 48, p 429-436
C.H. Quek, K.A. Khor, and P. Cheang, Influence of Processing Parameters in the Plasma Spraying of Hydroxyapatite/Ti-6Al-4V Composite Coatings, J. Mater. Process. Technol., 1999, 89-90, p 550-555
Y.P. Lu, S.T. Li, R.F. Zhu, and M.S. Li, Further Studies on the Effect of Stand-off Distance on Characteristics of Plasma Sprayed Hydroxyapatite Coating, Surf. Coat. Technol., 2002, 157, p 221-225
J.F. Li, H. Liao, B. Normand, C. Cordier, G. Maurin, J. Foct, and C. Coddet, Uniform Design Method for Optimization of Process Parameters of Plasma Sprayed TiN Coatings, Surf. Coat. Technol., 2003, 176, p 1-13
T.J. Steeper, D.J. Varacalle, Jr., G.C. Wilson, W.L. Riggs, A.J. Rotolico, and J.E. Nerz, A Design of Experiment Study of Plasma Sprayed Alumina-Titania Coatings, Thermal Spray: International Advances in Coatings Technology, 13th International Thermal Spray Conference, C.C. Berndt, Ed., 28th May-5th June, 1992, Orlando, FL, 1992
T.J. Steeper, D.J. Varacalle, Jr., G.C. Wilson, W.L. Riggs, A.J. Rotolico, and J.E. Nerz, Optimizing Plasma Spraying Alumina-Titania Coatings Using Statistical Methods, Thermal Spray Coatings: Research, Design and Applications, 5th National Thermal Spray Conference, C.C. Berndt and T.F. Bernecki, Ed., June 7-11, 1993, Anaheim, CA, 1993
J.R. Mawdsley, Y.J. Su, K.T. Faber, and T.F. Bernecki, Optimization of Small-Particle Plasma-Sprayed Alumina Coatings Using Designed Experiments, Mater. Sci. Eng. A, 2001, 308, p 189-199
T.J. Steeper, D.J. Varacalle, Jr., G.C. Wilson, W.L. Riggs, A.J. Rotolico, and J.E. Nerz, A Taguchi Design of Experiment Study of Plasma Sprayed Alumina Coatings, Thermal Spray Coatings: Research, Design and Applications, 1993
D.F. Gibbons and K.A. Buran, Microscopic Analysis of Retrieved Polymethylmethacrylate (PMMA) Bone Cement, Implant Retrieval: Material and Biological Analysis, National Bureau of Standards Special Publication 601, National Bureau of Standards, Washington, DC, 1981
B. Lin, M. Jean, and J. Chou, Using Response Surface Methodology for Optimizing Deposited Partially Stabilized Zirconia in Plasma Spraying, Appl. Surf. Sci., 2007, 253(6), p 3254-3262
J. Cizek, K.A. Khor, and Z. Prochazka, Influence of Spraying Conditions on Thermal and Velocity Properties of Plasma Sprayed Hydroxyapatite, Mater. Sci. Eng. C, 2007, 27(2), p 340-344
S. Dyshlovenko, C. Pierlot, L. Pawlowski, R. Tomaszek, and P. Chagnon, Experimental Design of Plasma Spraying and Laser Treatment of Hydroxyapatite Coatings, Surf. Coat. Technol., 2006, 201, p 2054-2060
S. Dyshlovenko, L. Pawlowski, P. Roussel, D. Murano, and A. Le Maguer, Relationship Between Plasma Spray Operational Parameters and Microstructure of Hydroxyapatite Coatings and Powder Particles Sprayed into Water, Surf. Coat. Technol., 2006, 200(12-13), p 3845-3855
J. Stokes, Theory and Application of Sulzer Metco High Velocity Oxy-Fuel (HVOF) Thermal Spray Process, © Dublin City University, 2008, ISBN 1-87232-753-2, ISSN 1649-8232
S.W.K. Kweh, K.A. Khor, and P. Cheang, Plasma-Sprayed Hydroxyapatite (HA) Coatings with Flame-Spheroidized Feedstock: Microstructure and Mechanical Properties, Biomaterials, 2000, 21, p 1223-1234
J. Stokes and L. Looney, HVOF System Definition to Maximise the Thickness of Formed Components, J. Surf. Coat. Technol., 2001, 148(1), p 18-24
F.W. Munjone and G. Irons, The Evolution of Thermal Spray Automation, Proceedings of the 5th National Thermal Spraying Conference, Anaheim, CA, USA, 1993, p 263-273
G. Irons, Thermal Spray Applications Speeds, Proceedings of the 14th International Thermal Spray Conference, Kobe, Japan, 1995, p 1165-1168
K.A. Gross, C.C. Berndt, and V.J. Iacono, Variability of Hydroxyapatite Coated Dental Implants, Int. J. Oral Maxillofac. Implants, 1998, 13, p 601-610
K.A. Gross, C.C. Berndt, and H. Herman, Formation of the Amorphous Phase in Hydroxyapatite Coatings, J. Biomed. Mater. Res., 1998, 39, p 407-414
BS ISO13779, Implants for Surgery-Hydroxyapatite. Part 1: Ceramic Hydroxyapatite, BS ISO 13779-1:2000, International Organisation for Standards, USA, 2000
Author information
Authors and Affiliations
Corresponding author
Additional information
This article is an invited paper selected from presentations at the 2010 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Thermal Spray: Global Solutions for Future Applications, Proceedings of the 2010 International Thermal Spray Conference, Singapore, May 3-5, 2010, Basil R. Marple, Arvind Agarwal, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2011.
Rights and permissions
About this article
Cite this article
Hasan, S., Stokes, J. Design of Experiment Analysis of the Sulzer Metco DJ High Velocity Oxy-Fuel Coating of Hydroxyapatite for Orthopedic Applications. J Therm Spray Tech 20, 186–194 (2011). https://doi.org/10.1007/s11666-010-9566-0
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11666-010-9566-0