Abstract
A numerical model was developed to simulate the jet-flow solid fraction of W18Cr4V high-speed steel during spray forming. The whole model comprises two submodels: one is an individual droplet model, which describes the motion and thermal behaviors of individual droplets on the basis of Newton’s laws of motion and the convection heat transfer mechanism; the other is a droplet distribution model, which is used to calculate the droplet size distribution. After being verified, the model was used to analyze the effects of parameters, including the initial gas velocity, deposition distance, superheat degree, and the ratio of gas-to-metal mass flow rates, on the jet-flow solid fraction. Finally, an equation to predict the jet-flow solid fraction directly and conveniently according to the parameters was presented. The values predicted by the equation show good agreement with those calculated by the numerical model.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
R.A. Mesquita and C.A. Barbosa, Spray forming high speed steel–properties and processing, Mater. Sci. Eng. A, 383(2004), No. 1, p. 87.
A. Schulz, V. Uhlenwinkel, C. Escher, R. Kohlmannc, A. Kulmburgd, M.C. Monteroe, R. Rabitschf, W. Schützenhöferf, D. Stocchig, and D. Vialeh, Opportunities and challenges of spray forming high-alloyed steels, Mater. Sci. Eng. A, 477(2008), No. 1-2, p. 69.
G.Q. Zhang, H. Yuan, D.L. Jiao, Z. Li, Y. Zhang, and Z.W. Liu, Microstructure evolution and mechanical properties of T15 high speed steel prepared by twin-atomiser spray forming and thermo-mechanical processing, Mater. Sci. Eng. A, 558(2012), p. 566.
Y. Xu, C.C. Ge, and Q. Shu, Microstructure, tensile properties and heat treatment process of spray formed FGH95 superalloy, J. Iron Steel Res. Int., 20(2013), No. 4, p. 59.
H.A. Godinho, A.L.R. Beletati, E.J. Giordano, and C. Bolfarini, Microstructure and mechanical properties of a spray formed and extruded AA7050 recycled alloy, J. Alloys Compd., 586(2014), Suppl.1, p. 139.
Y.D. Jia, F.Y. Cao, S. Scudino, P. Ma, H.C. Li, L. Yu, J. Eckert, and J.F. Sun, Microstructure and thermal expansion behavior of spray-deposited Al–50Si, Mater. Des., 57(2014), p. 585.
R.D. Cava, C. Bolfarini, C.S. Kiminami, E.M. Mazzer, W.J.B. Filho, P. Gargarella, and J. Eckert, Spray forming of Cu–11.85Al–3.2Ni–3Mn (wt%) shape memory alloy, J. Alloys Compd., 615(2014), suppl.1, p. 602.
P.S. Grant, B. Cantor, and L. Katgerman, Modelling of droplet dynamic and thermal histories during spray forming: I. Individual droplet behaviour, Acta Metall. Mater., 41(1993), No. 11, p. 3097.
P.S. Grant, B. Cantor, and L. Katgerman, Modelling of droplet dynamic and thermal histories during spray forming: II. Effect of process parameters, Acta Metall. Mater., 41(1993), No. 11, p. 3109.
P.S. Grant and B. Cantor, Modelling of droplet dynamic and thermal histories during spray forming: III. Analysis of spray solid fraction, Acta Metall. Mater., 43(1995), No. 3, p. 913.
J. Mi and P.S. Grant, Modelling the shape and thermal dynamics of Ni superalloy rings during spray forming: Part 1. Shape modeling—Droplet deposition, splashing and redeposition, Acta Mater., 56(2008), No. 7, p. 1588.
J. Mi and P.S. Grant, Modelling the shape and thermal dynamics of Ni superalloy rings during spray forming: Part 2. Thermal modelling—Heat flow and solidification, Acta Mater., 56(2008), No. 7, p. 1597.
W.D. Cai and E.J. Lavernia, Modeling of porosity during spray forming: Part I. Effects of processing parameters, Metall. Mater. Trans. B, 29(1998), No. 5, p. 1085.
W.D. Cai and E.J. Lavernia, Modeling of porosity during spray forming: Part II. Effects of atomization gas chemistry and alloy compositions, Metall. Mater. Trans. B, 29(1998), No. 5, p. 1097.
S. Kang and D.H. Chang, Modelling of billet shapes in spray forming using a scanning atomizer, Mater. Sci. Eng. A, 260(1999), No. 1-2, p. 161.
J.H. Hattel, N.H. Pryds, and T.B. Pedersen, An integrated numerical model for the prediction of Gaussian and billet shapes, Mater. Sci. Eng. A, 383(2004), No. 12, p. 184.
C.S. Cui and A. Schulz, Modeling and simulation of spray forming of clad deposits with graded interface using two scanning gas atomizers, Metall. Mater. Trans. B, 44(2013), No. 4, p. 1030.
J. Mi, P.S. Grant, U. Fritsching, O. Belkessam, I. Garmendia, and A. Landaberea, Multiphysics modelling of the spray forming process, Mater. Sci. Eng. A, 477(2008), No. 1-2, p. 2.
X. Jiang, G.A. Siamas, K. Jagus, and T.G. Karayiannis, Physical modelling and advanced simulations of gas–liquid two-phase jet flows in atomization and sprays, Prog. Energy Combust. Sci., 36(2010), No. 2, p. 131.
J. Gao, S.W. Park, Y. Wang, R.D. Reitza, S. Moon, and K. Nishida, Simulation and analysis of group-hole nozzle sprays using a gas jet superposition model, Fuel, 89(2010), No. 12, p. 3758.
J. Du and Z.Y. Wei, Numerical analysis of pileup process in metal microdroplet deposition manufacture, Int. J. Therm. Sci., 96(2015), p. 35.
Q.Q. Lu, J.R. Fontaine, and G. Aubertin, Numerical study of the solid particle motion in grid-generated turbulent flows, Int. J. Heat Mass Transfer, 36(1993), No. 1, p. 79.
E.S. Lee and S. Ahn, Solidification progress and heat transfer analysis of gas-atomized alloy droplets during spray forming, Acta Metall. Mater., 42(1994), No. 9, p. 3231.
P. Mathur, D. Apelian, and A. Lawley, Analysis of the spray deposition process, Acta Metall., 37(1989), No. 2, p. 429.
C.G. Levi and R. Mehrabian, Heat flow during rapid solidification of undercooled metal droplets, Metall. Trans. A., 13(1982), No. 2, p. 221.
J.E. Smith and M.L. Jordan, Mathematical and graphical interpretation of the log-normal law for particle size distribution analysis, J. Colloid Sci., 19(1964), No. 6, p. 549.
H. Lubanska, Correlation of spray ring data for gas atomization of liquid metals, JOM, 22(1970), No. 2, p. 45.
Acknowledgements
This work was financially supported by the National High-Tech Research and Development Program of China (No. 2012AA03A509) and the National Natural Science Foundation of China (No. 51204015).
Author information
Authors and Affiliations
Corresponding authors
Additional information
This article is published with open access at springer.longhoe.net
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Pi, Zq., Lu, X., Wu, Y. et al. Simulation of jet-flow solid fraction during spray forming. Int J Miner Metall Mater 24, 657–669 (2017). https://doi.org/10.1007/s12613-017-1448-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-017-1448-8