-
Article
Energy concept of hardness for instrumented indentation
The theoretical and experimental problems of determining Martell hardness are considered, and the use of an energy approach to the problem of hardness determination is analyzed. The development of instrumented...
-
Article
Effect of do** with refractory rare-earth metals on the structure and properties of Al–5Zn–3Mg alloys produced by powder metallurgy and casting methods
The effect of do** with transition refractory metals on the structure and properties of Al–Zn–Mg alloys produced by different methods is studied. It is ascertained that the strength of cast alloys is increas...
-
Article
Mechanical properties of type IIb synthetic diamond at a temperature of 900°C
Mechanical properties of a type IIb synthetic diamond produced by the temperature gradient method have been studied at 900°C using indenters having different angles between the pyramid axis and face. The strai...
-
Article
Structure and mechanical properties of iron after surface severe plastic deformation under friction with simultaneous nitrogen saturation: I. structure formation
The structure of armco iron after severe plastic deformation under friction with simultaneous nitrogen saturation has been studied by microstructure analysis, X-ray diffraction, and transmission and scanning e...
-
Article
Structure and mechanical properties of iron after surface severe plastic deformation under friction with simultaneous nitrogen saturation: II. The mechanical properties of nano- and submicrocrystalline iron saturated with nitrogen during deformation
The effect of structure refinement of iron to submicro- and nanograins during intense plastic deformation under friction (SPDF) with simultaneous nitrogen saturation on the mechanical characteristics (hardness...
-
Article
Assessment of the In-Service Degradation of Pipeline Steel by Destructive and Nondestructive Methods
We analyze the influence of the long-term operation of API X52 pipeline steel on the degradation of its mechanical properties. It is established that, after operation for 30 years, its strength and plasticity ...
-
Article
Physical nature of the temperature dependence of yield stress
Below is one of the most significant works by V. I. Trefilov and Yu. V. Mil’man. The idea that the temperature dependence of the yield stress is determined by the thermally activated escape of potential barrie...
-
Article
Structure and properties of Al–Mg alloys depending on scandium and zirconium additions and production methods
The paper examines how scandium and zirconium do** of Al–Mg alloys produced by conventional casting and powder metallurgy methods influences their structure and mechanical properties. It is shown that Al–Mg ...
-
Article
Mechanical properties of Al–Cu–Fe alloys sintered at high pressure
The structure and mechanical behavior of bulk Al–Cu–Fe materials sintered at high hydrostatic pressure are studied at room temperature. Quasicrystalline Al63Cu25Fe12 and Al62.7Cu25Fe12Sc0.3 powders and Al66Cu18Fe
-
Article
Al-Fe-Ce alloys based on water-atomized powders for high-temperature applications
The microstructure and mechanical properties of Al-Fe-Ce alloys based on water-atomized powders between 20 and 300 °C are examined in comparison with the properties of similar alloys produced by other rapid cr...
-
Article
Studies of mechanical properties of quasicrystalline Al-Cu-Fe phase by the indentation technique
-
Article
A method of determining the mechanical properties of a two-layer composite consisting of a steel matrix and a plasma spray coating based on amorphizing powders
A method is proposed for measuring failure stresses and elastic modulus for a coating by means of a four-point bending with precision deflection measurement. A composite has been examined...
-
Article
Structure and properties of Fe—Ni—Si—B and Co—Fe—Ni—Si—B alloys obtained by explosive compaction of amorphous powders
Hard (up to 16 GPa) amorphous-crystalline compacts of cobalt-based alloys and iron-based alloys are made by explosive compaction from powders at pressures of 12 and 15 GPa. Their magnetic properties correspond...
-
Article
Role of plastic deformation in sintering covalent crystals (review)
-
Article
Investigation of the special traits of failure of sintered iron by the in situ method
-
Article
Structural features of vacuum-deposited high-hardness chromium coatings
The structure and hardness of ion-plasma coatings, obtained by evaporating chromium with a low-pressure compressed arc, from a melting crucible with and without clusterization of the vapor flow, was studied. I...
-
Article
Structure features of the eutectic alloys of borides with the d- and f-transition metals
-
Article
Temperature of the subsurface layers and structural distortions in the grinding of polycrystalline tungsten
-
Article
Effect of annealing on the microhardness, the ductility, and the temperature of cold shortness of amorphous metallic alloys
-
Article
Mechanical properties of sintered materials. III. Cold brittleness of sintered materials