-
Article
Preparation and characterization of high hard and high tough ultrafine WC ceramics containing hybrid graphene and SiC nanowire
The aggregation of low-dimensional nanofillers in the host ceramic matrix significantly discounted their reinforcing efficiency. Herein, employing two-dimensional graphene (G) and one-dimensional SiC nanowire ...
-
Article
Study on suppression strategy of jet lag effect in melt electrowriting
The melt electrowriting (MEW) has broad applications in regenerative medicine and micro-nano electronics. It is an efficient micro-nano scale additive manufacturing technology; however, the fiber jet lag effec...
-
Chapter
Advanced Wireless Technologies for Industrial Automation
With the rapid development of wireless communication technologies, many advanced wireless technologies could be applied to industrial control system to improve the production efficiency. However, spectrum is a...
-
Book
-
Article
\(l_0\) Norm Constraint Bayesian Strategy for Direction-of-Arrival Estimation
Recent research on sparse signal reconstruction (SSR) shows that the sparse Bayesian learning (SBL) method is one of the most popular methods for direction-of-arrival (DOA) estimation. However, the high comput...
-
Article
Creep aging behavior and performance of Al-Zn-Mg-Cu alloys under different parameters in retrogression aging treatment
A study was conducted to better understand how different parameters, namely, regression aging time and regression aging temperature, affect the creep aging properties, i.e., the creep deformation and performan...
-
Article
Multifunctional interfacial and structural anode for dendrite-free lithium metal-based batteries
Lithium (Li) metal is considered as the candidate for the next generation of Li metal battery (LMB) anodes due to its high capacity and the lowest potential, which is expected to meet the requirements of energ...
-
Chapter and Conference Paper
Smart Shock Absorber
Autonomous and Electrical Vehicles are two development trends for automobile industry. Plenty of sensors are demanded to monitor the traffic condition in autonomous vehicle, hence sustainable and reliable powe...
-
Article
Open AccessHigh-speed visible light communication systems based on Si-substrate LEDs with multiple superlattice interlayers
High-speed visible light communication (VLC), as a cutting-edge supplementary solution in 6G to traditional radio-frequency communication, is expected to address the tension between continuously increased dema...
-
Article
Effects of niobium addition on microstructure and properties of CPM121 powder metallurgy high-speed steel
Massive vanadium additions as hard phases in powder metallurgy high-speed steels (PM HSS) lead to higher cost and bad machinability. In this study, ultrahigh alloy PM HSS with CPM121 (10W−5Mo−4Cr−10V−9Co, wt.%...
-
Chapter and Conference Paper
Foreseeing the Subversive Influence of Intelligent Simulation Technology for Battle Example Teaching
It is an important research project that exploring battle example teaching is how to serve the fight and drill preferably. The simulation territory has introduced artificial intelligence, virtual reality and c...
-
Chapter and Conference Paper
Subtractive Clustering for Categorical Data with a Novel Separation Difference Validity Index
The subtractive clustering method (SCM), proposed by Chiu in 1994, is an effective algorithm that can be used as an approximate clustering for numerical data. Since SCM heavily depends on parameter selections ...
-
Article
Decrease of Material Burden in a Novel Alkali-Saving Reduction Treatment Process of Nickel Slag Based on NaOH Roasting
Conventional reduction treatment methods for nickel slag show drawbacks such as high energy cost, heavy material burden or secondary pollution. Thus, a novel environmentally friendly reduction treatment method...
-
Article
Buckling Analysis of Steel H Column with Thermal Gradient Along the Flanges
This paper presents an analytical study about the axial compression buckling of H-section columns with one side of the flanges exposed to fire. The fire-induced thermal gradient along the flanges is obtained b...
-
Article
End-point dynamic control of basic oxygen furnace steelmaking based on improved unconstrained twin support vector regression
In order to improve the end-point hit rate of basic oxygen furnace steelmaking, a novel dynamic control model was proposed based on an improved twin support vector regression algorithm. The controlled objects ...
-
Article
An Analytical Solution of Local–Global Interaction Buckling of Cold-Formed Steel Channel-Section Columns
This paper presents an analytical approach to predict the critical load of global buckling with locally buckled channel-section columns under axial compressive loads. The effect of local deformation before glo...
-
Article
Effects of hot isostatic pressing temperature on casting shrinkage densification and microstructure of Ti6Al4V alloy
The Ti6Al4V alloy castings were produced by the investment casting process, and the hot isostatic pressing (HIP) was used to remove shrinkage from castings. The processing pressure and holding time for HIP wer...
-
Article
Bionic tracking method by hand & eye-vergence visual servoing
Animals rotate their eyes to gaze at the target prey, enhancing the ability of measuring the distance to the target precisely for catching it. These animals, visual tracking includes the triangular eye-vergenc...
-
Article
A study on robotic off-line programming system in induction hardening for fillets or chamfers of mould
As the end-effector of robot, the induction hardening tool is required to keep its orientations perpendicular to the fillets or chamfers of the mould at a distance during its uniform motion along the hardening...
-
Chapter
Opportunistic Communication Spectra Utilization
The objective of the monograph is to utilize the opportunistic spectra for VANETs through technologies such as CR, WiFi, and D2D communications. This chapter introduces the background and surveys the literatur...