![Loading...](https://link.springer.com/static/c4a417b97a76cc2980e3c25e2271af3129e08bbe/images/pdf-preview/spacer.gif)
-
Article
Effect of the windshield perforation patterns on the cooling performance in centrifugal separators
The cooling performance of a centrifuge was enhanced using a perforated windshield. The windshield spatially separates the rotor and the chamber, reducing turbulence and air resistance. On the other hand, duri...
-
Article
Temperature control-based design of variable dam** and lightweight gear bodies
The sustainability of today’s industry turned into a critical requirement on account of energy cost increases, environmental pollution, and carbon emissions. As an important segment in mechanical drive, the vi...
-
Article
Machine vision-based recognition of elastic abrasive tool wear and its influence on machining performance
This study presents a novel Hunter-Prey Optimization (HPO)-optimized Otsu algorithm in tool wear assessment and machining process quality control. The algorithm is explicitly tailored to address the challenges...
-
Article
Design of personal mobility system for assisted agricultural work with self-adjusting center of gravity
A personal mobility system with a self-adjusting center of gravity is designed to aid agricultural work. This personal mobility system can assist elderly and disabled people with mobility problems to perform s...
-
Chapter and Conference Paper
Static and Dynamic Behavior of Shallow Foundation Reinforced by Honey Cell Modular Block
The construction of residential building and industrial complex in the soft ground is rather difficult to meet the requirement by the design code in terms of settlement as well as bearing capacity. There are a...
-
Article
Investigation of anisotropy in microstructure and thermoelectric properties of large-scaled p-type Bi–Sb–Te sintered body made by hot pressing
In this work, a large-sized pellet of about 200 g (Ф40 × 23 mm) of p-type polycrystalline based Bi–Sb–Te was prepared using gas atomization and hot pressing processes. A systematic investigation was conducted on ...
-
Article
Experimental investigation on a static rollover angle model for commercial vehicle: new measurement method and theoretical model for double rear axle vehicle
An experimental validation of a theoretical model was performed to simulate the static rollover angle of a commercial vehicle. The theoretical model was derived based on the center of gravity model and the sta...
-
Article
Multi-parameter optimization-based design of lightweight vibration-reduction gear bodies
Due to increasing energy costs, related environmental impacts, and carbon emissions, sustainable development has become an important task for industry. As one of the important links in mechanical transmission,...
-
Article
Numerical study on mixing performance of separate-type HVAC system for industrial vehicles
Industrial vehicles have no vehicle-induced wind in operation mode, so they require more than one fan to secure enough air. Thus, a separate-type HVAC system with two fans is proposed in this study. Thanks to ...
-
Article
Investigation of homogeneity in microstructure and thermoelectric properties at various positions in high-thickness sintered bulks of p-type 20%Bi2Te3–80%Sb2Te3 alloys
Thermoelectric devices are environmentally friendly renewable energy sources that use waste heat to generate electricity. So far, p-type Bi–Sb–Te-based alloys with high thermoelectric properties were fabricate...
-
Article
Targeted alpha immunotherapy of CD20-positive B-cell lymphoma model: dosimetry estimate of 225Ac-DOTA-rituximab using 64Cu-DOTA-rituximab
The aim of this study was to evaluate the radiation dosimetry of alpha-emitter 225Ac-DOTA-rituximab using Monte Carlo simulation of 64Cu-DOTA-rituximab.
-
Article
Open AccessLong-term surgical outcomes of primary retropupillary iris claw intraocular lens implantation for the treatment of intraocular lens dislocation
We aimed to investigate the efficacy and safety of primary retropupillary iris claw intraocular lens (R-IOL) implantation in patients with complete intraocular lens (IOL) dislocation. In this single-center ret...
-
Article
Reduction Of Generated Axial Force by Constant Velocity Joint Using Contact Optimization of Tripod Joint
Constant velocity (CV) joints are the primary component of a vehicle that transmits the driving force from an engine/transmission to a wheel at a constant speed. A CV joint comprises numerous mechanical parts....
-
Article
Glucose-6-phosphatase Expression–Mediated [18F]FDG Efflux in Murine Inflammation and Cancer Models
2-Deoxy-2-[18F]fluoro-d-glucose ([18F]FDG) accumulation in inflammatory lesions can confound the diagnosis of cancer. In this study, we investigated [18F]FDG accumulation and efflux in relation to the genes and p...
-
Article
Adenine Nucleotide Translocase 2 as an Enzyme Related to [18F] FDG Accumulation in Various Cancers
Although glucose transporter 1 (GLUT1) and hexokinase 2 (HK2) are known as major proteins involved in the molecular mechanisms for accumulating 2-deoxy-2-[18F]fluoro-D-glucose ([18F]FDG) in cancer cells, sometime...
-
Article
LINEAR RECURRENCE RELATIONS IN Q-SYSTEMS VIA LATTICE POINTS IN POLYHEDRA
We prove that the sequence of the characters of the Kirillov–Reshetikhin (KR) modules ...
-
Article
High Thermoelectric Figure of Merit in p-Type (Bi2Te3)x − (Sb2Te3)1−x Alloys Made from Element-Mechanical Alloying and Spark Plasma Sintering
p-Type (Bi2Te3)x − (Sb2Te3)1−x alloys with high thermoelectric properties were fabricated for waste heat energy recovery by mechanical alloying followed by spark plasma sintering. The samples’ diffraction peaks, ...
-
Article
Design optimization of a knee joint for an active transfemoral prosthesis for weight reduction
This paper describes the optimized design of a knee joint for an active transfemoral prosthesis with a fully active knee joint. The active transfemoral prosthesis which can help amputees to walk naturally with...
-
Article
Open AccessEffect of stick-slip on magneto-rheological elastomer with a magnetic field
This study investigated the stick-slip characteristics of a magneto-rheological elastomer (MRE) against an aluminum plate. Herein, the MRE was manufactured, and a stick-slip tester was employed to evaluate the...
-
Article
Friction and wear of textured surfaces produced by 3D printing
Surface texture patterns have great potential for improving tribological performance in terms of reducing friction and wear. The most common methods for surface texturing are laser and injection molding. The 3...