Search
Search Results
-
Investigation on performance of composite phase change material based thermal management of electrical battery
The utilization of lithium-ion batteries in electric vehicles presents challenges due to the heat generated the during charging and discharging...
-
Selecting the coupling variable to synchronize nonlinear oscillators
The choice of which state variable to use in coupling network oscillators is a critical factor to reach synchronization. Nonetheless, few works have...
-
An intellectual drivers' sensitivity traffic model for adapting taillight effects
In this study, a traffic flow model, the so-called Taillight Adapting (TA) traffic model, is developed considering the driver's activities impact...
-
Dynamic model refining and identification for accurate gait control of a powered knee–ankle prosthesis
The knowledge of an accurate dynamic model is of fundamental importance for implementing model-based control. However, the model parameters of...
-
A novel remote sensing image encryption scheme based on block period Arnold scrambling
In this paper, a new spatiotemporal chaos model is proposed to improve the security and anti-decryption capability of remote sensing image encryption...
-
Optimum design parameters for double concave friction pendulum system considering ground motion characteristics and friction heating
Double concave friction pendulum system (DCFPS) performs well in the vibration control of building structures, while its effectiveness is limited due...
-
Ultra-local model-based prescribed performance assist-as-needed control for series elastic actuator-based upper limb patient-exoskeleton system under complex state constraints
In this paper, an ultra-local model-based prescribed performance assist-as-needed control scheme (UPPAC) is presented for series elastic...
-
Feasibility of a 9 THz HgTe/HgCdTe quantum-well vertical-cavity surface-emitting laser
We propose an original design for a HgCdTe-based terahertz vertical-cavity surface-emitting laser with twenty 5 nm HgTe quantum wells. Feasibility of...
-
A Novel Four legged linear piezoelectric inchworm motor with high thrust force
A major limitation of most linear motors is limited travel range and low load capacity. In this research, a large motion range piezoelectric Inchworm...
-
Effects of interrupted aging T6I4 on hardness and fracture toughness of aeronautic AA7050 alloy
Al–Zn–Mg–Cu alloys have been extensively researched for aeronautical uses due to their good mechanical properties. Among these alloys, AA7050 is...
-
Nonlinear dynamics of planetary gearboxes containing cracks
Gear cracks may occur during the operation of planetary driveline, leading to a huge safety hazard. However, few studies have been conducted to...
-
Dynamic characteristics and test research of multibody system considering uneven wear clearances
The wear of rotating pair is a significant factor for the failure of mechanical systems. Currently, some scholars have undertaken investigations on...
-
Finite element analysis and experimental investigation in incremental sheet metal forming of composite matrix of Grade-V titanium
The single point incremental forming (SPIF) method is well-suited to meet the demands of the biomedical and aerospace sectors and a wide range of...
-
Kadomtsev–Petviashvili equation with self-consistent sources: breathers, lumps and their interactions
Under investigation in this paper is the Kadomtsev–Petviashvili (KP) equation with self-consistent sources. We adopt two different bilinear systems...
-
State and disturbance observer based robust disturbance rejection control for friction electro-hydraulic load simulator
Friction electro-hydraulic load simulator (FEHLS) classified as an electro-hydraulic torque servo mechanism, encounters significant challenges in the...
-
A low-cost robotic system for simultaneous localization and map**
This paper presents a low-cost system for simultaneous localization and map** (SLAM) for unknown indoor environments. The system is based on a...
-
Optimization and prediction of resistance seam weld quality in secondary coated steels using machine learning
With the use of ethanol blended fuel, secondary coating on steel becomes crucial to enhance the corrosion resistance in fuel tanks. Resistance seam...
-
Analyzing torsional vibration in restrained functionally graded nanobeams: nonlocal Lam strain gradient approach
This research explores the free torsional vibration behavior of a functionally graded (FG) circular nanobeam, constrained at both ends by torsion...
-
A fuzzy computational framework for dynamic multibody system considering structure damage based on information entropy
The present study proposes a new fuzzy finite element method for dynamic multibody interaction with consideration for structural damage. Here, fuzzy...
-
Rotation dynamics of double-walled carbon nanotube bundles during in-plane compressive deformation
The nonlinear rotational behavior of radially deformed double-walled carbon nanotube (DWCNT) bundles is investigated using all-atom molecular...