Abstract
The features of the InAs, InSb, GaAs, and GaSb ultra-smooth surface have been investigated using chemical–mechanical polishing with the (NH4)2Cr2O7–HBr–CH2(OH)CH2(OH)-etching solutions. The etching rate of the semiconductors has been measured as a function of the solution saturation by organic solvent (ethylene glycol). It was found that mechanical effect significantly increases the etching rate from 1.5 to 57 µm/min, and the increase of the organic solvent concentration promotes the decrease of the damaged layer-removing rate. According to AFM, RS, HRXRD results, the treatment with the (NH4)2Cr2O7–HBr–ethylene glycol solutions produces the clean surface of the nanosize level (Ra < 0.5 nm).
Similar content being viewed by others
References
Bassignana IC et al (1997) Setting limits on the accuracy of X-ray determination of Al concentration in AlGaAs/GaAs epitaxial layers. J Cryst Growth 172:25–36
Carles R et al (1984) Raman studies of non-stoichiometric amorphous GaSb films. Philos Mag B 49(1):63–71
Eminov SO (2011) Wet chemical etching of the In and (111) Sb planes of InSb substrates. Inorgan Mater 47(4):394–398
Hartnagel H et al (1973) A contribution to etch polishing of GaAs. J Mater Sci 8(7):1061–1063
Levchenko IV et al (2017) Features of the chemical polishing of InAs, GaAs, InSb and GaSb crystals in the (NH4)2Cr2O7–HBr–CH2(OH)CH2(OH) solutions [in Russian]. Voprosy khimii i khim tekhnologii 2(111):29–35
Lin Z-C et al (2012) A study of material removal amount of sapphire wafer in application of chemical mechanical polishing with different polishing pads. J Mech Sci Technol 26(8):2353–2364
Marinescu ID et al (2006) Handbook of lap** and polishing. Taylor & Francis Group, LLC CRC Press
Martinez R et al (2013) Towards the production of very low defect GaSb and InSb substrates: bulk crystal growth, defect analysis and scaling challenges. In: Proceedings of SPIE 8631: 86311N-1—86311N-8
Matovu JB et al (2013) Fundamental investigation of chemical mechanical polishing of GaAs in silica dispersions: material removal and arsenic trihydride formation pathways. ECS J Solid State Sci Technol. 2(11):P432–P439
Meng Q et al (2017) Operation limitation of CMP in back-thinning process of InSb IRFPAs. Opt Quant Electron 49(211):1–11
Papis E et al (2001) Chemical processing of GaSb related to surface preparation and patterning. In: Proceedings of SPIE, vol 4413, pp 82–88
Pashchenko HA et al (2015) Features of the GaAs wafers polishing by chemical–dynamic and non-contact chemical–mechanical methods [in Ukraininan]. Fiz i khim tv tila 16(3):560–564
Vangala SR et al (2006) Molecular beam epitaxy and morphological studies of homoepitaxial layers on chemical mechanical polished InSb (100) and InSb (111) B substrates. J Vacc Sci Technol B 24(3):1634–1638
Vurgaftman I et al (2001) Band parameters for III–V compound semiconductors and their alloys. Appl Phys 89(11):5815–5875
Zhou X et al (2011) Optical properties of GaSb nanofibers. Nanoscale Res Lett 6(6):1–6
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Levchenko, I., Tomashyk, V., Stratiychuk, I. et al. Formation of the InAs-, InSb-, GaAs-, and GaSb-polished surface. Appl Nanosci 8, 949–953 (2018). https://doi.org/10.1007/s13204-018-0788-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13204-018-0788-7