Abstract
The present research aim is to synthesize the aluminum alloy hybrid composite by using different weight percentages of SiC (0wt%, 5wt%, 10wt%, & 15wt%) and Al2O3 (0wt%, 9wt%, 7wt%, and 5wt%) nanoparticle blended with 500 rpm and 700 rpm stir speed via stir casting route assisted with vacuum die casting (2 × 105 bar) to limit the porosity and enhance the density, hardness, impact, yield, and tensile strength of the composites. The influences of stir speed on SEM, physical, and mechanical behavior of the aluminum hybrid composite was experimentally studied. The SEM micrograph revealed the homogenous particle distribution proved with good interface bonding between matrix and reinforcement. The investigation results of the hybrid nanocomposite prepared by 700 rpm stir speed with inversely increased content of SiC and Al2O3 show decreased porosity percentages of less than 1%,and its density was increased nominally. The composite containing 15wt% SiC and 5wt% Al2O3 is found to have superior mechanical properties as the hardness, impact, and tensile strength are enhanced by 49.2%, 20.47%, and 33.15% as compared to Al–Mg cast alloy. Finally, the developed hybrid aluminium alloy composite with exemplary behaviour is recommended for steel bridge construction applications.
Similar content being viewed by others
Data Availability
All the data required are available within the manuscript.
References
ASM Handbook (2001) Composites. Novelty. ASM International, OH, USA, p 21
Zhou D, Qiu F, Jiang Q (2014) Simultaneously increasing the strength and ductility of nanosized TiN particle reinforced Al-Cu matrix composites. Mater Sci Eng A 596:98–102
Thirugnanasambandham T, Chandradass J, Baskara Sethupathi P, Leenus Jesu Martin M, Fabrication and Mechanical Properties of Alumina Nanoparticle Reinforced Magnesium Metal Matrix Composite by Stir Casting Method. SAE Tech Paper, 2018–28–0098, https://doi.org/10.4271/2018-28-0098
Geng R, Zhao Q, Qiu F, Jiang Q (2020) Simultaneously increased strength and ductility via the hierarchically heterogeneous structure of Al-Mg-Si alloys/nanocomposite. Mater Res Lett 8(6):225–231. https://doi.org/10.1080/21663831.2020.1744759
Kawasaki M, Jang J-i (2017) Micro-Mechanical Response of an Al-Mg Hybrid System Synthesized by High-Pressure Torsion. Materials 10:596. https://doi.org/10.3390/ma10060596
Hassan SF, Gupta M (2002) Development of high strength magnesium based composites using elemental nickel particulates as reinforcement. J Mater Sci 37:2467–2474
Lloyd DJ (1994) Particle reinforced aluminium and magnesium matrix composites. Int Mater Rev 39:1–23
Smith LN, Midha PS, Graham AD (1998) Simulation of metal powder compaction, for the development of a knowledge-based powder metallurgy advisor. J Mater Process Technol 79(1):94–100
Mortensen A (2006) Concise encyclopedia of composite materials advances in materials sciences and engineering. Technology & Engineering Materials Science General. Elsevier Science, p 1050
Natrayan L, Merneedi A (2021) Experimental investigation on wear behaviour of bio-waste reinforced fusion fiber composite laminate under various conditions. Mater Today: Proc 37:1486–1490
Rashad M, Pan F, Liu Y, Chen X (2016) High-temperature formability of grapheme nanoplatelets-AZ31 composites fabricated by stir-casting method. J Magnes Alloy 4:270–277. https://doi.org/10.1016/2016-11-003
Prabu S, Karunamoorthy L, Kathiresan S, Mohanb B (2006) Influence of stirring speed and stirring time on the distribution of particles in cast metal matrix composite. J Mater Process Technol 171:268–273
Aravindan S, Rao PV, Ponappa K (2015) Evaluation of Physical and Mechanical Properties of AZ91D/SiC Composites by Two Step Stir Casting Process. J Magnes Alloys 3:52–62
Baradeswaran A, Elayaperumal A (2014) Study on mechanical and wear properties of Al 7075/ Al2O3/graphite hybrid composites. Compos Part B: Eng 56:464–471
Kok M, Ozdin M (2007) Wear resistance of aluminium alloy and its composites reinforced by Al2O3 particles. J Mater Process Technol 183(2–3):301–309
Madhukar P, Selvaraj N, Rao CSP, Veeresh Kumar GB (2020) Fabrication and characterization two-step stir casting with ultrasonic-assisted novel AA7150-hBN nanocomposites. J Alloys Compd 815:152464
Monikandan VV, Joseph MA, Rajendrakumar PK (2016) Dry sliding wear studies of aluminium matrix hybrid composites. Resour Eff Technol 2(1):12–24. https://doi.org/10.1016/j.reffit.2016.10.002
Ravikumar K, Pridhar T, SreeBalaji VS (2018) Mechanical properties and characterization of zirconium oxide (ZrO2) and coconut shell ash(CSA) reinforced aluminium (Al 6082) matrix hybrid composite. J Alloys Compd 765:171–179
Na Guan L, Geng L, Wei Zhang H, Jun Huang L (2011) Effects of stirring parameters on microstructure and tensile properties of (ABOwþ/SiCp)/6061Al composites fabricated by semi-solid stirring technique. Trans Nonferrous Metals Soc China 21(2):274–279. https://doi.org/10.1016/s1003-6326(11)61590-2
Carvalho O, Buciumeanu M, Madeira S, Soares D, Silva FS, Miranda G (2015) Dry sliding wear behaviour of AlSi-CNTs-SiCphybrid composites. Tribol Int 90:148–156
Suryakumai TSA, Ranganathan S (2018) Preparation and Study the Wear Behaviour of Aluminium Hybrid Composite. Mater Today Proc 5(2):8104–8111. https://doi.org/10.1016/j.matpr.2017.11.497
Lakshmipathy J, Kulendran B (2014) Reciprocating wear behaviour of 7075Al /SiC in comparison with 6061Al/ Al2O3 composites. Int J Refract Hard Mealt 46:137–144
Karakoc H, Karabulut S, Citak R (2018) Study on mechanical and ballistic performances of boron carbide reinforced Al 6061 aluminium alloy produced by powder metallurgy. Compos B Eng 148:68–80
Ding Y, Wang J, Zhao M, Ju D (2018) Effect of annealing temperature on joints of diffusion bonded Mg/Al alloys. Transit Nonferrous Met Soc China 28:251–258
Weglowski MS (2018) Friction Stir processing-State of the art. Arch Civ Mech Eng 18:114–129
Inegbenebor AO, Bolu CA, Babalola PO, Inegbenebor AI, Fayomi OS (2018) Aluminum silicon carbide particulate metal matrix composite development via stir casting processing. Silicon 10:343–347
Soltani S, Khosroshahi AR, Taherzadeh MR, Jiang ZY, Boostani AV, Brabazon D (2017) Stir casting process for the manufacture of Al-SiC composites. Rare Met 36:581–590
Karthik R, Gopalakrishnan K, Venkatesh R, Krishnan AM, Marimuthu S (2022) Influence of stir casting parameters in mechanical strength analysis of Aluminium Metal Matrix Composites (AMMCs). Mater Today: Proc 62(4):1965–1968
Rahman M, Dey A, Pandey KM (2018) Machinability of cenosphere particulate-reinforced AA6061 aluminium alloy prepared by compocasting. Proc Inst Mech Eng, Part B 232:2499–2509
Prasad KNP, Ramachandra M (2018) Determination of Abrasive Wear Behaviour of Al-Fly ash Metal Matrix Composites produced by Squeeze casting. Mater Today: Proc 5:2844–2853
Chung DDL (2010) Composites Materials science and applications. Springer, London
ThirugnanaSambandham T, Chandradass J, BaskaraSethupathi P, Kannan TTM (2019) Experimental Investigation of Silicon Carbide Nanoparticles Reinforced Magnesium Alloy (AZ91E) Metal Matrix Composite by Vacuum Stir Casting Method. SAE Tech Paper 28:0169
Prasad Reddy A, Vamsi Krishna P, RN Rao (2018) Mechanical and wear properties of aluminum-based nanocomposites fabricated through ultrasonic assisted stir casting J Test Eval https://doi.org/10.1520/JTE20170560
Manna A, Bains HS, Mahapatra PB (2011) Experimental study on fabrication of Al-Al2O3/Grp metal matrix composites. J Compos Mater 0(0):1–8
Funding
• The authors did not receive support from any organization for the submitted work.
• No funding was received to assist with the preparation of this manuscript.
• No funding was received for conducting this study.
• No funds, grants, or other support were received.
Author information
Authors and Affiliations
Contributions
All authors contributed to the study's conception and design. Material preparation, data collection and analysis were performed by P. Raja Sekaran, H. Ramakrishnan, R. Venkatesh, and A. Nithya. The first draft of the manuscript was written by [R. Venkatesh] and all authors provided language help, writing assistance and proofreading of the manuscript. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Ethics Approval
This is an observational study. Mechanical and physical Characterization Studies of Nano Ceramic Reinforced Al–Mg Hybrid Nanocomposites, Research Ethics Committee has confirmed that no ethical approval is required.
Consent to Participate
Informed consent was obtained from all individual authors included in the study.
Consent for Publication
We give our consent for the publication of Mechanical and Physical Characterization Studies of Nano Ceramic Reinforced Al–Mg Hybrid Nanocomposites to be published in the Silicon Journal.
Competing & Financial Interests
• The authors have no relevant financial or non-financial interests to disclose.
• The authors have no competing interests to declare relevant to this article's content.
• All authors certify that they have no affiliations with or involvement in any organization or entity with any financial or non-financial interest in the subject matter or materials discussed in this manuscript.
• The authors have no financial or proprietary interests in any material discussed in this article.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Sekaran, P.R., Ramakrishnan, H., Venkatesh, R. et al. Mechanical and Physical Characterization Studies of Nano Ceramic Reinforced Al–Mg Hybrid Nanocomposites. Silicon 15, 4555–4567 (2023). https://doi.org/10.1007/s12633-023-02473-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12633-023-02473-9