Abstract
The room temperature tensile properties of Ti-6Al-4V alloy prepared under two different processing routes were evaluated and compared. One group of samples was prepared by conventional casting-forging-rolling into flat plates. The other group was prepared by using Triton’s Laser Free-Form Fabrication (LF3)™ processes, i.e., a laser was used to melt pre-alloyed powders of the required metallic composition as they were dropped onto a moveable substrate programmed to move in such a manner as to form a solid alloy plate. Five populations of Ti-6Al-4V were evaluated: a standard wrought form, an as-deposited form, a machined as-deposited form, a heat-treated as-deposited form, and a machined as-deposited and heat-treated form. The poorest mechanical properties occurred with the rough surfaces, likely due to existing microcracks and stress concentrations. The LF3™ as-deposited material had mechanical properties comparable to, if not higher than, the mechanical properties of the wrought material. Further evaluations of the laser-formed material for complex spacecraft piece parts were warranted, specifically in regards to improving the surface finish of the materials.
Similar content being viewed by others
References
M. Donachie, Titanium, A Technical Guide, 2nd ed., ASM International, Materials Park, OH 44073, 2000, p 5–8
H.R. Salimijazi, T.W. Coyle, and J. Mostaghimi, Vacuum Plasma Spraying: A New Concept for Manufacturing Ti-6Al-4V Structures, JOM, September 2006, p 50–56
R. Boyer, G. Welsch, and E.W. Collings, Ed., Materials Properties Handbook: Titanium Alloys, ASM International, Materials Park, OH, 1998, p 3–31
R. Witt, Inside Sales Manager, Service Steels Aerospace, (P) 800.624.8073, http://www.ssa-corp.com/quotation.asp, August 24, 2009
K.G. Watkins, S.P. Edwardson, J. Magee, G. Dearden, and P. French, Laser Forming of Aerospace Alloys, Aerospace Manufacturing Technology Conference (AMTC), SAE, 2001, p 1–7
B.V. Krishna and A. Bandyopadhyay, Surface Modification of AISI 410 Stainless Steel Using Laser Engineered Net Sha** (LENStm), Mater. Des., 2008, doi:10.1016/j.matdes.2008.08.003
R. Banerjee et al., Microstructural Evolution in Laser Deposited Compositionally Graded Alpha/Beta Titanium-Vanadium Alloys, Acta Mater., 2003, 51, p 3277–3292
D.M. Keicher and W.D. Miller, LENS Moves Beyond RP to Direct Fabrication, Metal Powder Rep., 1998, 53, p 26–28
B. Cleveland, Rapid Manufacturing Technologies, Adv. Mater. Process., 2001, 159(5), p 32
J. Brooks, C. Robino, T. Headley, S. Goods, and M. Griffith, Microstructure and Property Optimization of LENS Deposited H13 Tool Steel. Solid Freeform Fabrication Proc, University of Texas, Austin, 1999
P.L. Blackwell and A. Wisbey, Laser-aided Manufacturing Technologies; Their Application to the Near-Net Shape Forming of a High-Strength Titanium Alloy, J. Mater. Process. Technol., 2005, 170, p 268–276
K.P. Cooper, Building Components by Laser-Additive Processing, JOM, 2001, 53(9), p 29
P.A. Kobryn and S.L. Semiatin, Mechanical Properties of Laser-Deposited Ti-6Al-4V, AFRL/MLLMP, p 179–186
S.M. Kelly, S.L. Kampe, and C.R. Crowe, Microstructural Study of Laser Formed Ti-6Al-4V, Solid Freeform and Additive Fabrication Symposium, Vol. 625, 2000, p 3–8
P.A. Kobryn and S.L. Semiatin, The Laser Additive Manufacture of Ti-6Al-4V, JOM, 2001, 53, p 40–42
S.L. Semiatirn et al., Plastic Flow and Microstructure Evolution during Thermomechanical Processing of Laser-Deposited Ti-6Al-4V Performs, Met. Mater. Trans. A, 2001, 32A, p 1802
MIL Standard H-812008, Jan 13, 1991
G. Kehl, Principles of Metallographic Laboratory Practice, 3rd ed., McGraw-Hill Book Publishing Company, New York, 1949
S.A. Salpekar, I.S. Raju, and T.K. O’Brien, Strain-Energy Release Rate Analysis of Delamination in a Tapered Laminate Subjected to Tension Load, J. Compos. Mater., 1991, 25, p 118
SAE-AMS-T-9046, “Titanium and Titanium Alloy, Sheet, Strip, and Plate,” 17 September 1999
O.S. Es-Said, J. Foyos, R. Noorani, M. Mendelson, and B. Pregger, Effect of Layer Orientation on Mechanical Properties of Rapid Prototyped Samples, Mater. Manuf. Process., 2000, 15(1), p 112
A.S. Brown, Rapid Prototy**: Parts Without Tools, Aerospace America, 1991, p 18
Acknowledgments
The authors wish to acknowledge the financial support for this project from the National Science Foundation, Grant No. EEC 0097863. They also wish to thank Ms. Jaisey Simard and Mr. Roman Silva for preparing the manuscript.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Alcisto, J., Enriquez, A., Garcia, H. et al. Tensile Properties and Microstructures of Laser-Formed Ti-6Al-4V. J. of Materi Eng and Perform 20, 203–212 (2011). https://doi.org/10.1007/s11665-010-9670-9
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-010-9670-9