Abstract
To elucidate the mechanism of formation of inclusions in microalloyed spring steel deoxidized by Si, their number, morphology, and chemical compositions were analyzed by electron probe X-ray microanalysis. Wavelength-dispersive spectrometry and Monte Carlo simulation were used to confirm the existence of inherent FeO in the inclusions. Additions of Nb and V did not have an observable influence on the formation of inclusions. Based on the major chemical compositions, the inclusions in spring steel were classified into four types: CaO-SiO2, Al2O3-SiO2, Al2O3-SiO2-CaO, and MnS. Most CaO-SiO2 inclusions were around 10 μm in diameter, with their composition close to that of the refining slag and liquidus temperatures all below 1400 °C. The Al2O3-SiO2 inclusions were mainly attributed to deoxidization products. They were usually multiphased with liquidus temperatures higher than 1500 °C and smaller than 10 μm in diameter. Most Al2O3-SiO2-CaO inclusions with high Al2O3 and SiO2 contents originated from the coalescence of CaO-SiO2 and Al2O3-SiO2 inclusions; those with high CaO and SiO2 contents were considered to form via reduction of CaO-SiO2 inclusions by Al dissolved in the steel.
Similar content being viewed by others
References
Q.Y. Wang, J.Y. Berard, S. Rathery and C. Bathias: Fatigue Fract. Eng. Mater. Struct., 1999, vol. 22, pp. 673-7.
D. McClaflin and A. Fatemi: Int. J. Fatigue, 2004, vol. 26, pp. 773-84.
G. Farrahi, J. Lebrijn and D. Couratin: Fatigue Fract. Eng. Mater. Struct., 1995, vol. 18, pp. 211-20.
B. Pyttel, D. Schwerdt and C. Berger: Int. J. Fatigue, 2011, vol. 33, pp. 49-58.
P. Ganesh, R. Sundar, H. Kumar, R. Kaul, K. Ranganathan, P. Hedaoo, G. Raghavendra, S.A. Kumar, P. Tiwari, D.C. Nagpure, K.S. Bindra, L.M. Kukreja and S.M. Oak: Mater. Des., 2014, vol. 54, pp. 734-41.
H. Tashiro, S. Nishida, T. Tarui, S. Ohashi, S. Sasaki and K. Nakamura, A. Yoshie and H. Demachi: Nippon Steel Technical Report, 1999, vol. 80, pp. 4-5.
M. Kimura: Research and Development Kobe, 2006, vol. 56, p. 1.
C.W. Anderson and S.G. Coles: Extremes, 2002, vol. 5, pp. 237-52.
Y. Murakam, T. Nomoto and T. Ueda: Fatigue Fract. Eng. Mater. Struct., 1999, vol. 22, pp. 581-90.
Y. Murakami: JSME Int. J. Ser. A, 1989, vol. 32, pp. 167–80.
Y. Akiniwa, S.S. Tschegg, H. Mayer, M. Wakita and K. Tanaka: Int. J. Fatigue, 2008, vol. 30, pp. 2057-63.
Y. Akiniwa, S.S. Tschegg and S. Konuma: Int. J. Fatigue, 1989, vol. 11, pp. 291-8.
J. Zhang, S. Li, Z. Yang, G. Li, W. Hui and Y. Weng: Int. J. Fatigue, 2007, vol. 29, pp. 765-71.
Z. Yang, J. Zhang, S. Li, G. Li, Q. Wang, W. Hui and Y. Weng: Mater. Sci. Eng. A, 2006, vol. 427, pp. 167-74.
W.J. Hui, H. Dong and S.L. Chen: Special Steel, 1998, vol. 6, p. 1.
J. Kawahara, K. Tanabe, T. Banno and M. Yoshida: Wire J. Int. (USA), 1992, vol. 25, pp. 55-61.
Z. Yang, G. Yao, G. Li, S. Li, Z. Chu, W. Hui, H. Dong and Y. Weng: Int. J. Fatigue, 2004, vol. 26, pp. 959-66.
H. Tozawa, Y. Kato, K. Sorimachi and T. Nakanishi: ISIJ Int., 1999, vol. 39, pp. 426-34.
R. Tsu**o, K. Mukai, W. Yamada, M. Zeze and S. Mizoguchi: Tetsu-to-Hagané, 1999, vol. 85, pp. 362-7.
H. Ohta and H. Suito: ISIJ Int., 1996, vol. 36, pp. 983-90.
K. Lee, J.M. Park, J.Y. Chung, S.H. Choi and S.B. Ahn: Rev. Métall., 1996, vol. 93, pp. 503-9.
J.H. Park and H. Todoroki: ISIJ Int., 2010, vol. 50, pp. 1333-46.
K. Beskow, J. Jia, C. Lupis and S.C. Du: Ironmak. Steelmak., 2002, vol. 29, pp. 427-35.
V. Brabie: Steel Res. Int., 1997, vol. 68, pp. 54-60.
V. Brabie: ISIJ Int., 1996, vol. 36, pp. S109-12.
H. Yang, J. Ye, X. Wu, Y. Peng, Y. Fang and X. Zhao: ISIJ Int., 2016, vol. 56, pp. 108-15.
J.T. Ju, Z.L. Lv and S.F. Yang: Met. Min. Ind., 2014, vol. 6, pp. 18-24.
K.Y. Lee, J.Y. Lee and D.R. Kim: Mater. Sci. Eng., 1984, vol. 67, pp. 213-20.
S. Nishijima, E. Suzuki, A. Morii, T. Obata, K. Uchibori, Y. Nikura, K. Nisawa, J. Koarai and Y. Itoh: Trans. Jpn. Soc. Spr. Eng., 1986, vol. 1986, pp. 113-38.
H. Suito and R. Inoue: ISIJ Int., 1996, vol. 36, pp. 528-36.
A.B. Stepanov, A.I. Zaitsev, B.A. Sarychev, A.Yu. Dzyuba and A.V. Koldaev: Metallurgist, 2016, vol. 59, pp. 917-22.
Z.B. Li and Z.L. Xue: Iron and Steel, 1999, vol. 34, pp. 20-3.
G. Du and H. Guo: Spec. Steel, 2016, vol. 37, pp. 18-22.
K. Wang, M. Jiang, X. Wang, Y. Wang, H. Zhao and Z. Cao: Metall. Mater. Trans. B, 2015, vol. 46, pp. 2198-207.
H. Fredriksson and Ö. Hammar: Metall. Trans. B, 1980, vol. 11, pp. 383-408.
S. Choudhary: J. Mater. Process, 2012, vol. 27, pp. 925-9.
S. Choudhary, S. Chandra and A. Ghosh: Metall. Mater. Trans. B, 2005, vol. 36, pp. 59-66.
B. Koroušić: Steel Res., 1991, vol. 62, pp. 285-8.
H. Ohta and H. Suito: Metall. Mater. Trans. B, 1996, vol. 27, pp. 943-53.
S. Maeda, T. Soejima and T. Saito, 72nd Steelmaking Conference Proceedings, 1989, Iron and Steel Society, Warrendale, PA, pp. 379-85.
S.H. Chen, M. Jiang, X.F. He and X.H. Wang: Int. J. Miner. Metall. Mater., 2012, vol. 19, pp. 490-8.
X.F. Cai, Y.P. Bao, L. Lin and C. Gu: Steel Res. Int., 2016, vol. 87, pp. 1168-78.
K. Wang, M. Jiang, X. Wang, Y. Wang, H. Zhao and Z. Cao: Metall. Mater. Trans. B, 2016, vol. 47, pp. 282-90.
J. Stewart and D. Williams: Corros. Sci., 1992, vol. 33, pp. 457–63, 465–74.
M. Tohjoh, I. Muto, A. Chiba, Y. Sugawara and N. Hara: ECS Trans., 2014, vol. 58, pp. 39-45.
W. Roberts, B. Lehtinen and K. Easterling: Acta Metall., 1976, vol. 24, pp. 745-58.
Kluken, A.O., Ø. Grong and J. Hjelen: Mater. Sci. Technol., 1988, vol. 4, pp. 649-54.
L. Wang and C. Beckermann: Metall. Mater. Trans. B, 2006, vol. 37, pp. 571-88.
R. Neiser, M. Smith and R. Dykhuizen: J. Therm. Spray Technol., 1998, vol. 7, pp. 537-45.
D.C. Hilty and W. Crafts: J. Met., 1950, vol. 2, pp. 414-24.
D.C. Hilty and W. Crafts: J. Met., 1950, vol. 2, pp. 425-36.
Y. Kawashita and H. Suito: ISIJ Int., 1995, vol. 35, pp. 1459-67.
W. Choi, H. Matsuura and F. Tsukihashi: ISIJ Int., 2011, vol. 51, pp. 1951-6.
Y. Bi, A.V. Karasev and P. Jönsson: ISIJ Int., 2013, vol. 53, pp. 2099-109.
H. Doostmohammadi, A. Karasev and P. Jönsson: Steel Res. Int., 2010, vol. 81, pp. 398-406.
T. Gram: PhD thesis. KTH Royal Institute of Technology, Sweden, 2015.
J.H. Qi, C.W. Yang, W.J. Zhu, T. Qu, Y. Liu, Y.Ji: Iron & Steel, 2013, vol. 48, pp. 79-83.
W. Yang, X.G. Yang, L.F. Zhang, X.F. Liu: Steelmaking, 2013, vol. 6, pp. 71-8.
Chang, Z. Wu, R. Shiue, C. Chang: Mater. Lett., 2007, vol. 61, pp. 842-5.
S.T. Lindsay, M.K. James, E.J. Bunce, S.M. Imber, H. Korth, A. Martindale, T.K. Yeoman: Planet. Space Sci., 2016, vol. 125, pp. 72-9.
S. Kimura, K. Nakajima and S. Mizoguchi: Metall. Mater. Trans. B, 2001, vol. 32, pp. 79-85.
L. Zhang and B. Thomas: Metall. Mater. Trans. B, 2006, vol. 37, pp. 733-61.
M. Faraji, D. Wilcox, R. Thackray, A. Howe, I. Todd and P. Tsakiropoulos: Metall. Mater. Trans. B, 2015, vol. 46, pp. 2490-502.
M. Ende, M. Guo, E. Zinngrebe, R. Dekkers, J. Proost, B. Blanpain and P. Wollants: Ironmak. Steelmak., 2009, vol. 36, pp. 201-8.
L. Chen, A. Malfliet, P. Jones, B. Blanpain and M. Guo: Ceram. Int., 2016, vol. 42, pp. 743-51.
S.M. Huang, J.L. Xue and Z.G. Wang: Proceedings 8th International Symposium on High-Temperature Metallurgical Processing, J.-Y. Hwang, T. Jiang, M.W. Kennedy, O. Yucel, P. Pistorius, V. Seshadri, B. Zhao, D. Gregurek and E. Keskinkilic, eds., The Minerals, Metals & Materials Series, Springer International Publishing, pp. 679–88, 2017.
A. Ikesue, H. Yamamoto, H. Shikano and K. Hiragushi: Advances in Refractories Technology. Proceedings of International Forum on Advances in Refractories Technology, R.E. Fisher, ed., American Ceramics Society, Westerville, OH, 1989, pp. 464–88.
X. Chen, C. Shi, H. Guo, F. Wang, H. Ren and D. Feng: Metall. Mater. Trans. B, 2012, vol. 43, pp. 1596-1607.
C.B. Shi, X.C. Chen, H.J. Guo, Z.J. Zhu and X.L. Sun: Metall. Mater. Trans. B, 2013, vol. 44, pp. 378-89.
Drouin, A.R. Couture, D. Joly, X. Tastet, V. Aimez, R. Gauvin: Scanning, 2007, vol. 29, pp. 92-101.
C.W. Bale, E. Bélisle, P. Chartrand, S. Decterov, G. Eriksson, A. Gheribi, K. Hack, I.H. Jung, Y.B. Kang, J. Melançon: Calphad, 2016, vol. 54, pp. 35-53.
M. Allibert, H. Gaye, J. Geiseler, D. Janke, B.J. Keene, D. Kirner, M. Kowalski, J. Lehmann, K.C. Mills and D. Neuschütz, Slag Atlas, 2nd ed., Verlag Stahleisen GmbH, Düsseldorf, 1995, p. 160.
W. Yang, C.B. Guo, L.F. Zhang, H.T. Ling and C. Li: Metall. Mater. Trans. B, 2017, vol. 48, pp. 2717-30.
Acknowledgments
This work was supported by the Australian Research Council and Baosteel Australia Research and Development Centre. The University of Queensland International Research Tuition Award and China Scholarship Council provided scholarships for Mr Sha Lyu. The Australian Microscopy & Microanalysis Research Facility is thanked for providing characterization facilities. Technical supports for the EPMA facility from Mr. Ron Rasch and Ms. Ying Yu of the Centre for Microscopy and Microanalysis at the University of Queensland are gratefully acknowledged. We thank Kathryn Sole, PhD, from Edanz Group (www.edanzediting.com/ac) for editing a draft of this manuscript.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted April 18, 2018.
Rights and permissions
About this article
Cite this article
Lyu, S., Ma, X., Huang, Z. et al. Inclusion Characterization and Formation Mechanisms in Spring Steel Deoxidized by Silicon. Metall Mater Trans B 50, 732–747 (2019). https://doi.org/10.1007/s11663-019-01505-3
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11663-019-01505-3