Abstract
Quality is a primary focus to both maintain and increase customers. A manufacturing production process and service business’s failure impacts operational costs. Assessments are needed to instigate fabrication process failure and maintain good quality output. PT AA is a fabrication contractor firm that experienced process failures in the steel fabrication division. This study aims to evaluate the steel fabrication process to recommend improvement solutions to eliminate failures at the fabrication stage. Failure mode and effect analysis was used as the research approach. The result of the research found that two defects, namely peeling and ruuns, in the painting process gain the highest defect numbers with 117 compared to other stages. With a score of 576, the highest risk of defects ruuns the painting process. Recommendations for improvement are that the company’s management regularly provides briefings and education on the importance of SOPs and installing SOP stickers on every painting equipment and tools.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Li H, Teixeira AP, Guedes SC (2020) A two-stage failure mode and effect analysis of offshore wind turbines. Renew Energy 162:1438–1461
Doshi J, Desai D (2017) Application of failure mode & effect analysis (FMEA) for continuous quality improvement—multiple case studies in automobile SMEs. Int J Qual Res 11(2):345–360
Hernawan A, Mahbubah NA (2021) Integrasi statistical process control dan failure mode and effect analysis guna meminimalisasi defect Pada Proses Produksi Pipa PVC. J Engine Energi Manufaktur dan Mater 5(2):65
Priambodo S, Mahbubah NA (2021) Implementasi metode overall equipment effectiveness berbasis six big losses guna mengevaluasi efektivitas mesin packing semen. J Serambi Eng 6(4):2363–2374
Prajapati DR (2012) Implementation of failure mode and effect analysis: a literature review. Int J Manage IT Eng 2(7):264–292
Sharma KD, Srivastava S (2018) Failure mode and effect analysis (FMEA) implementation: a literature review. J Adv Res Aeronaut Sp Sci 5(1&2):1–17
Hasanah TU, Wulansari T, Putra T, Fauzi M (2020) Penerapan lean manufacturing dengan Metode Takt time dan FMEA untuk Mengidentifikasi waste pada proses Produksi steril PT.XYZ. J Rekayasa Sist Ind 07(02):1–7
Pratama FS, Suhartini S (2019) Analisis Kecacatan Produk dengan Metode Seven Tools dan FTA dengan Mempertimbangkan Nilai Risiko berdasarkan Metode FMEA. J Senopati 1(1):41–49
Krisnaningsih E, Wirawati SM, Febriansyah Y (2021) Penerapan statistical process control (SPC) dan failure mode effect analysis (FMEA) pada proses Produksi Tisu Wajah. J PASTI 14(3):293
Khasanah SN, Mahbubah NA, Hidayat H (2021) Deteksi defect proses Produksi Sarung Menggunakan ATBM Berbasis failure mode and effect analysis. Jati Emas (Jurnal Apl Tek dan Pengabdi Masyarakat) 5(3):143–150
Rislamy AF, Mahbubah NA, Widyaningrum D (2020) Analisis Risiko Kerusakan Pada Alat Berat Grab Dengan Metode failure mode and effect analysis (Studi Kasus: PT Siam Maspion Terminal Gresik). Profisiensi 8(1):36–43
Lestari A, Mahbubah NA (2021) Analisis defect proses Produksi Songkok Berbasis Metode FMEA Dan FTA di home—Industri Songkok GSA Lamongan. J Serambi Eng 6(3):2197–2206
Anthony MB (2018) Analisis Penyebab Kerusakan Hot Rooler Table dengan Menggunakan Metode failure mode and effect analysis (FMEA). J INTECH Tek Ind Univ Serang Raya 4(1):1
Suherman A, Cahyana BJ (2019) Pengendalian Kualitas dengan metode failure mode effect and analysis (FMEA) Dan Pendekatan Kaizen untuk Mengurangi Jumlah Kecacatan dan Penyebabnya. In: Seminar Nasional Sain dan Teknologi, pp 1–9
Prasetya RY, Suhermanto S, Muryanto M (2021) Implementasi FMEA dalam Menganalisis Risiko Kegagalan proses Produksi Berdasarkan RPN. Performa Media Ilm Tek Ind 20(2):133–138
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Aini Mahbubah, N., Muid, A., Atho’illah, A.A. (2024). Managing Defects in Steel Fabrication Process Using Failure Mode and Effect Analysis Approach. In: Irwansyah, Iqbal, M., Huzni, S., Akhyar (eds) Proceedings of the 4th International Conference on Experimental and Computational Mechanics in Engineering. ICECME 2022. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-99-7495-5_5
Download citation
DOI: https://doi.org/10.1007/978-981-99-7495-5_5
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-7494-8
Online ISBN: 978-981-99-7495-5
eBook Packages: EngineeringEngineering (R0)