Abstract
This paper presents a computer-based design approach of a piezoelectric valveless micropump which consists of a piezoelectric element, a diaphragm, a pump chamber, two diffusers, an inlet, and an outlet. The diaphragm and the piezoelectric element act as the actuator of the micropump. In the study, geometric parameters of the actuator, diffusers and external parameters are numerically analyzed in a Multiphysics environment using structural analysis and fluid structure interaction (FSI) simulations. At first, the ratios between the diameters and the thicknesses are evaluated considering the maximum volumetric change of the diaphragm for a specific frequency and voltage. Then, the trends of the flow rate against the geometric parameters of the diffusers of the micropump are investigated to select suitable geometric parameters based on the flow rate. Furthermore, the effect of external parameters on the flow rate is studied. A direct relationship is observed between the displacement of the diaphragm and the applied voltage. The flow rate of the micropump increases exponentially when the width of the short side and the length of the diffuser decreases. Additionally, curve fitting is used to identify the relationship of flow rate with the applied voltage and the operating frequency which showed a quadratic and linear relationship respectively.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Hettiarachchi, S., et al.: Design and development of a microfluidic droplet generator with vision sensing for lab-on-a-chip devices. Sens. Actuators A: Phys. 332, 113047 (December 2021). https://doi.org/10.1016/j.sna.2021.113047
Suriyage, M.P. et al.: Design and simulation of a novel MEMS based microfluidic circulating tumor cell (CTC) detection system for a lab on a chip device. IOP Conf. Ser.: Mater. Sci. Eng. 895, 012016 (July 2020). https://doi.org/10.1088/1757-899X/895/1/012016
Liu, B., Dong, S., Tan, J., Li, D., Yang, J.: Design and flow simulation of a micro steam jet pump. Mod. Phys. Lett. B 36(9), 2250018 (March 2022). https://doi.org/10.1142/S021798492250018X
Sampath, W.H.P., Hettiarachchi, S.P., Melroy, N.H.R.G., Amarasinghe, Y.W.R.: Design and development of a droplet-based microfluidics system using laser fabrication machining techniques for a lab on a chip device. In: Chen, Y.-W., Tanaka, S., Howlett, R.J., Jain, L.C. (eds.) Innovation in Medicine and Healthcare, vol. 192, pp. 201–210. Springer Singapore, Singapore (2020). https://doi.org/10.1007/978-981-15-5852-8_19
Wang, Y.-N., Fu, L.-M.: Micropumps and biomedical applications – A review. Microelectron. Eng. 195, 121–138 (August 2018). https://doi.org/10.1016/j.mee.2018.04.008
Hettiarachchi, S., Melroy, G., Mudugamuwa, A., Perera, N., Sampath, P., Amarasinghe, R.: 3D printed multi-channel peristaltic pump with active droplet generator for lab-on-a-chip devices. In: Scholz, S.G., Howlett, R.J., Setchi, R. (eds.) Sustainable Design and Manufacturing, vol. 262, pp. 235–244. Springer Singapore, Singapore (2022). https://doi.org/10.1007/978-981-16-6128-0_23.
Ashraf, M.W., Tayyaba, S., Afzulpurkar, N.: Micro electromechanical systems (MEMS) based microfluidic devices for biomedical applications. IJMS 12(6), 3648–3704 (June 2011). https://doi.org/10.3390/ijms12063648
Fan, B., Song, G., Hussain F.: Simulation of a piezoelectrically actuated valveless micropump. Smart Mater. Struct. 14(2), 400–405 (April 2005). https://doi.org/10.1088/0964-1726/14/2/014
Nisar, A., Afzulpurkar, N., Mahaisavariya, B., Tuantranont, A.: MEMS-based micropumps in drug delivery and biomedical applications. Sens. Actuators B: Chem. 130(2), 917–942 (March 2008). https://doi.org/10.1016/j.snb.2007.10.064
Cui, Q., Liu, C., Zha, X.F.: Simulation and optimization of a piezoelectric micropump for medical applications. Int. J. Adv. Manuf. Technol. 36(5–6), 516–524 (March 2008). https://doi.org/10.1007/s00170-006-0867-x
S. Hettiarachchi, A. Mudugamuwa, Amarasinghe, R.: Microfluidic channel network analysis of a lab-on-a-chip device using electrical circuit analogy. In: 2020 From Innovation to Impact (FITI), pp. 1–4. Colombo, Sri Lanka (December 2020). https://doi.org/10.1109/FITI52050.2020.9424888
Jeong, J., Kim, C.N.: A numerical simulation on diffuser-nozzle based piezoelectric micropumps with two different numerical models. Int. J. Numer. Meth. Fluids 53(4), 561–571 (February 2007). https://doi.org/10.1002/fld.1294
Cui, Q., Liu, C., Zha, X.F.: Study on a piezoelectric micropump for the controlled drug delivery system. Microfluid Nanofluid 3(4), 377–390 (June 2007). https://doi.org/10.1007/s10404-006-0137-0
Muralt, P.: Recent progress in materials issues for piezoelectric MEMS’, J. Am. Ceram. Soc. 91(5), 1385–1396 (May 2008). https://doi.org/10.1111/j.1551-2916.2008.02421.x
Asadi Dereshgi, H., Yildiz, M.Z.: Numerical study of novel MEMS-based valveless piezoelectric micropumps in the range of low voltages and frequencies. In: 2019 Scientific Meeting on Electrical-Electronics & Biomedical Engineering and Computer Science (EBBT), pp. 1–4. Istanbul, Turkey (April 2019). https://doi.org/10.1109/EBBT.2019.8741629
Nhu, C.N., Van, L.L., Ngoc, A.N., Dau, V.T., Bui, T.T., Duc, T.C.: A valveless micropump based on additive fabrication technology. IJNT 15(11/12), 1010 (2018). https://doi.org/10.1504/IJNT.2018.099938
Wei, X., et al.: A piezoelectric power generator based on axisymmetrically distributed PVDF array for two-dimension vibration energy harvesting and direction sensing. Sustain. Energy Technol. Assess. 44, 101001 (April 2021). https://doi.org/10.1016/j.seta.2021.101001
Shen, D., Choe, S.-Y., Kim, D.-J.: Analysis of piezoelectric materials for energy harvesting devices under high- g vibrations. Jpn. J. Appl. Phys. 46(10A), 6755–6760 (October 2007). https://doi.org/10.1143/JJAP.46.6755
Melroy, G., et al.: PZT based active microfluidic droplet generator for lab-on-a-chip devices. In: Scholz, S.G., Howlett, R.J., Setchi, R. (eds.) Sustainable Design and Manufacturing, vol. 262, pp. 277–289. Springer Singapore, Singapore (2022). https://doi.org/10.1007/978-981-16-6128-0_27
Acknowledgements
The authors would like to express their gratitude to the Accelerating Higher Education Expansion and Development (AHEAD) - Development Oriented Research (DOR) grant of the Centre for Advanced Mechatronic Systems (CFAMS), University of Moratuwa, Sri Lanka for their financial contribution and the CFAMS for their valuable advice and guidance towards the success of the research.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Dodampegama, S. et al. (2023). Novel Design and Simulation Approach for a Piezoelectric Micropump with Diffusers. In: Scholz, S.G., Howlett, R.J., Setchi, R. (eds) Sustainable Design and Manufacturing. SDM 2022. Smart Innovation, Systems and Technologies, vol 338. Springer, Singapore. https://doi.org/10.1007/978-981-19-9205-6_16
Download citation
DOI: https://doi.org/10.1007/978-981-19-9205-6_16
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-19-9204-9
Online ISBN: 978-981-19-9205-6
eBook Packages: EngineeringEngineering (R0)