Abstract
Mg-Al joining is problematic due to dissimilar high-temperature flow characteristics that often result in defects and brittle intermetallic compounds (IMC) at the interface. Process development on lap joining of 1.27 mm 6022 (top sheet) and 1.5 mm ZEK100 (bottom sheet) intended for an automotive door application is presented. Process development was conducted in linear welding using power control (modulating torque and spindle speed) with multiple tool designs and welding parameters. Process variables were correlated to micro- and macro-structure and mechanical properties. A 2D computational model was created to understand the failure mechanism and contribution of mechanical interlocking towards joint strength. Joint efficiency of 48% (compared to base 6022 Al) at a welding speed of 0.625 m/min has been demonstrated thus far. For a thin (<2 mm) automotive sheet with a softer material as a bottom sheet, adequate control of process variables is critical to maintain weld stability and avoid excessive IMC layer at the interface. A combination of mechanical anchoring and metallurgical reaction is likely responsible for bonding.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Kostka A, Coelho RS, Santos J dos, Pyzall AR (2009) Microstructure of friction stir welding of aluminum alloy to magnesium alloy. Scr Mater 60 : 953–956. https://www.sciencedirect.com/science/article/pii/S1359646209001080
Mohammadi J, Behnamian Y, Mostafaei A, Gerlich AP (2015) Tool geometry, rotation and travel speeds effects on the properties of dissimilar magnesium/aluminum friction stir welded lap joints. Mater Des 75: 95–112. https://www.sciencedirect.com/science/article/pii/S0261306915001004
Chen YC, Nakata K (2008) Friction stir lap joining aluminum and magnesium alloys. Scr Mater 58: 433–436. https://www.sciencedirect.com/science/article/pii/S1359646207007713
Shen JJ, Li Y, Zhang T, Peng D, Wang D, Xu N (2015) Preheating friction stir spot welding of Mg/Al alloys in various lap configurations. Sci Technol Weld Join 20 (1): 1–10. https://doi.org/10.1179/1362171814Y.0000000248
Kwon YJ, Shigematsu I, Saito N (2008) Dissimilar friction stir welding between magnesium and aluminum alloys. Mater Lett 62: 3827–3829. https://www.sciencedirect.com/science/article/pii/S0167577X08004369
Buffa G, Baffari D, Di Caro A, Fratini L (2015) Friction stir welding of dissimilar aluminum-magnesium joints: sheet mutual position effects. Sci Technol Weld Join 20 (4): 271–279. https://doi.org/10.1179/1362171815Y.0000000016
Venkateswaran P, Reynolds AP (2012) Factors affecting the properties of Friction Stir Welds between aluminum and magnesium alloys. Mater Sci Eng A 545: 26–37. https://www.sciencedirect.com/science/article/pii/S0921509312002870
Fu BL, Qin GL, Li F, Meng XM, Zhang JZ, Wu C S (2015) Friction stir welding process of dissimilar metals of 6061-T6aluminum alloy to AZ31 B magnesium alloy. J Mater Process Technol 218: 38–47. https://www.sciencedirect.com/science/article/pii/S0924013614004634
Ji S, Li Z, Zhang L, Zhou Z, Chai P (2016) Effect of lap configuration on magnesium to aluminum friction stir lap welding assisted by external stationary shoulder. Mater Des 103: 160–170. https://www.sciencedirect.com/science/article/pii/S0264127516305408
Mohammadi J, Behnamian Y, Mostafaei A, Izadi H, Saeidd T, Kokabi AH, Gerlich AP (2015) Friction stir welding joint of dissimilar materials between AZJ 1 B magnesium and 6061 aluminum alloys: microstructure studies and mechanical characterizations. Mater Charact 101: 189–207. https://www.sciencedirect.com/science/article/pii/S1044580315000108?via%3Dihub
Liang ZY, Chen K, Wang XN, Yao JS, Yang Q, Zhang LT, Shan AO (2013) Effect of tool offset and tool rotational speed on enhancing mechanical property of Al/Mg dissimilar FSW joints. Metal Mater Trans A 44A: 3721–3731. https://doi.org/10.1007/s11661-013-1700-4
Smith M (2009) ABAQUS/Standard User's Manual, Version 6.9, Dassault Systems Simulia Corp, United States
Elices MG, Guinea GV, Gomez J, Planas J (2002) The cohesive zone model: advantages, limitations and challenges. Eng Fracture Mech 69(2):137–63. https://www.sciencedirect.com/science/article/pii/S0013794401000832
Khan AS, Huang S (1995) Continuum theory of plasticity. Wiley, New York. https://www.wiley.com/en-us/Continuum+Theory+of+Plasticity-p-9780471310433
Wang T, Tamayo DR, Jiang X, Kitsopoulos P, Kuang W, Gupta V, Barker E, Upadhyay P (2020) Effect of interfacial characteristics on magnesium to steel joint obtained using FAST. Mater. Des. 28:108697. https://www.sciencedirect.com/science/article/pii/S0264127520302318
Johnson GR, Cook WH (1998) Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech 21(1):31–48. https://www.sciencedirect.com/science/article/pii/0013794485900529
Acknowledgements
PNNL is operated by Battelle Memorial Institute for the U.S. Department of Energy under contract DE-AC05-76RL01830. This work was sponsored by the DOE- EERE, Vehicle Technology under project titled “Phase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints” partnership of Worcester Polytechnic Institute, Oak Ridge National Lab and Magna. We are thankful to Daniel Graff to assist during welding; Anthony Guzman for metallographic preparation; Tim Roosendaal, Ethan Nickerson, and Robert Seffens for mechanical testing and DIC analysis; and Joshua Silverstein for SEM characterization. The authors appreciate material support provided by Tim Skszek, Magna.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Minerals, Metals & Materials Society
About this paper
Cite this paper
Das, H., Upadhyay, P., Kulkarni, S.S., Choi, W. (2021). Dissimilar Joining of ZEK100 and AA6022 for Automotive Application. In: Hovanski, Y., Sato, Y., Upadhyay, P., Naumov, A.A., Kumar, N. (eds) Friction Stir Welding and Processing XI . The Minerals, Metals & Materials Series. Springer, Cham. https://doi.org/10.1007/978-3-030-65265-4_11
Download citation
DOI: https://doi.org/10.1007/978-3-030-65265-4_11
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-65264-7
Online ISBN: 978-3-030-65265-4
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)