Abstract
The aim of the study was to develop a methodology for measuring the structural and geometric parameters of a straight bull-nose cutter. To test the effectiveness of the developed methodology for measuring the structural and geometric parameters of the cutter, a full-scale experiment was conducted. During the experiment, all the structural and geometric parameters of the straight bull-nose cutter were measured using handheld measuring tools and a coordinate measuring machine Wenzel XOrbit 55 (Germany). A comparative analysis of the results of measurements using a universal handheld measuring tool and coordinate measuring machine showed: all the geometrical parameters of the cutter can only be measured using a coordinate measuring machine; the results of measuring geometric parameters using a universal handheld measuring tool do not allow making unambiguous organizational decisions on the further operation of the cutting tool, since the measurement error is comparable with the current size tolerances; however, for such design parameters as length, height, width of the cutter due to large tolerances, the use of a universal handheld tool is sufficient. The practice of measurements using a coordinate measuring machine has shown that, when conducting critical measurements, the use of coordinate measuring machines is not only accurate, but also more productive in comparison with the use of handheld measuring tools.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Vykhristyuk IA (2010) Coordinate measuring machine with large working volume based on laser technological system. Key Eng Mater 437:453–457. https://doi.org/10.4028/www.scientific.net/KEM.437.453
Ito S, Kodama I, Gao W (2014) Development of a probing system for a micro-coordinate measuring machine by utilizing shear-force detection. Meas Sci Technol 25(6):064011. https://doi.org/10.1088/0957-0233/25/6/064011
Chang HC, Lin AC (2011) Five-axis automated measurement by coordinate measuring machine. Int J Adv Manuf Technol 55:657–673. https://doi.org/10.1007/s00170-010-3092-6
He G, Sang Y, Pang K et al (2018) An improved adaptive sampling strategy for freeform surface inspection on CMM. Int J Adv Manuf Technol 96:1521–1535. https://doi.org/10.1007/s00170-018-1612-y
Yu M, Zhang Y, Li Y et al (2013) Adaptive sampling method for inspection planning on CMM for free-form surfaces. Int J Adv Manuf Technol 67(9–12):1967–1975. https://doi.org/10.1007/s00170-012-4623-0
Poniatowska M (2012) Deviation model based method of planning accuracy inspection of freeform surfaces using CMMs. Meas J Int Meas Confed 45(5):927–937. https://doi.org/10.1016/j.measurement.2012.01.051
Gao C, Cheng K, Webb D (2004) Investigation on sampling size optimisation in gear tooth surface measurement using a CMM. AMT 24:599–606. https://doi.org/10.1007/s00170-003-1595-0
Lee S, Yang D (2003) Improvement of Product Accuracy in Freeform Surface Machining. Int J Adv Manuf Technol 21:972–979. https://doi.org/10.1007/s00170-002-1419-7
Li Y, Nomula PR (2015) Surface-opening feature measurement using coordinate-measuring machines. Int J Adv Manuf Technol 79:1915–1929. https://doi.org/10.1007/s00170-015-6968-7
Zuikova NA (2000) Measuring complicated surfaces with coordinate-measuring machines. Meas Tech 43:733–734. https://doi.org/10.1007/bf02503643
Woźniak A, Mayer JRR, Bałaziński M, Côté M (2006) Investigation on precise measurement of cutting tool edges using coordinate measuring machines. In: CIRP 2nd international conference on high performance cutting, University of British Columbia, Vancouver, Canada, 12–13 June 2006
Zongwei Y, Yu** Z, Shouwei J (2003) Methodology of NURBS surface fitting based on off-line software compensation of errors of a CMM. Precision Eng 27:299–303
Zhang X, Tsang W, Yamazaki K et al (2013) A study on automatic on-machine inspection system for 3D modeling and measurement of cutting tools. J Intell Manuf 24:71–86. https://doi.org/10.1007/s10845-011-0540-6
Surkov IV (2011) Development of methods and means of coordinate measurements for linear and angular parameters of cutting instruments. Meas Tech 54:758–763. https://doi.org/10.1007/s11018-011-9800-2
Krehel R, Pollak M (2016) The contactless measuring of the dimensional attrition of the cutting tool and roughness of machined surface. Int J Adv Manuf Technol 86:437–449. https://doi.org/10.1007/s00170-015-8197-5
Siddhpura A, Paurobally RA (2013) Review of flank wear prediction methods for tool condition monitoring in a turning process. Int J Adv Manuf Technol 65:371–393. https://doi.org/10.1007/s00170-012-4177-1
Chizhov VN, Petrovskaya IM, Trykov YP et al (1990) Instrument for measuring the radius of round-off of the cutting edges of cutting tools and hard alloy plates. Meas Tech 33:560–562. https://doi.org/10.1007/bf00977915
Shiou FJ, Lin YF, Chang KH (2003) Determination of the optimal parameters for free form surface measurement and data processing in reverse engineering. Int J Adv Manuf Technol 21:678–690. https://doi.org/10.1007/s00170-002-1390-3
Vrba I, Palencar R, Hadzistevic M et al (2015) Different approaches in uncertainty evaluation for measurement of complex surfaces using coordinate measuring machine. Meas Sci Rev 15(3):111–118. https://doi.org/10.1515/msr-2015-0017
Jakubiec W, Płowucha W, Starczak M (2012) Analytical estimation of coordinate measurement uncertainty. Measurement 45(10):2299–2308. https://doi.org/10.1016/j.measurement.2011.09.027
Jakubiec W, Płowucha W, Rosner P (2016) Uncertainty of measurement for design engineers. Proc CIRP 43:309–314. https://doi.org/10.1016/j.procir.2016.02.027
Acknowledgements
The study was carried out with the financial support of the RFBR (Russian Foundation for Basic Research) in the framework of the scientific project no. 20-08-00410.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Nikitina, I.P., Kamenev, S.V., Polyakov, A.N. (2021). Methodology of Measuring Cutters by Using Coordinate Measuring Machine in Automatic Mode. In: Radionov, A.A., Gasiyarov, V.R. (eds) Proceedings of the 6th International Conference on Industrial Engineering (ICIE 2020). ICIE 2021. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-54817-9_11
Download citation
DOI: https://doi.org/10.1007/978-3-030-54817-9_11
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-54816-2
Online ISBN: 978-3-030-54817-9
eBook Packages: EngineeringEngineering (R0)