Abstract
The critical technical information for the drill design and process parameter selection for drilling of Ti alloys is the spatial and temporal distributions of temperature of the drill. The high and concentrated temperature at the drill tip softens the drill material and promotes rapid diffusion wear, chemical reaction, and drill wear and edge chip**. The drill temperature is studied experimentally or numerically in this chapter. Because the heat generation rate and drill temperature are difficult to measure directly during drilling, numerical modeling is a necessary tool to predict the temperature inside the drill. The inverse heat transfer method with the combination of experimental measurement and numerical modeling is presented in this chapter to find the drill temperature during drilling.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Tueda M, Hasegawa Y, Nisina Y (1961) The study of cutting temperature in drilling: 1st report, on the measuring method of cutting temperature. Trans Jpn Soc Mech Eng 27:1423–1430
Watanabe K, Yokoyama K, Ichimiya R (1975) Thermal analyses of the drilling process. J Jpn Soc Precis Eng 41:1078–1083
Agapiou JS, Stephenson DA (1994) Analytical and experimental studies of drill temperatures. J Eng Ind 116:54–60
Arai M, Ogawa M (1997) Effects of high pressure supply of coolant in drilling of titanium alloy. J Jpn Inst Light Met 47:139–144
Bono M, Ni J (2002) A method for measuring the temperature distribution along the cutting edges of a drill. J Manuf Sci Eng 124:921–923
Chen L, Tai BL, Chaudhari R, Song X, Shih AJ (2017) Measurement of machined surface temperature in hard turning. Int J Mach Tools Manuf 121:10–21
Chen L, Tai BL, Yang JA, Shih AJ (2017) Experimental study and finite element modeling of workpiece temperature in finish cylinder boring. ASME J Manuf Sci Eng 139:1–11
DeVries MF, Wu SM, Mitchell JW (1967) Measurement of drilling temperature by the garter spring thermocouple method. Microtec J 21:583–586
Bono M, Ni J (2001) The effects of thermal distortions on the diameter and cylindricity of dry drilled holes. Int J Mach Tools Manuf 41:2261–2270
Bagci E, Ozcelik B (2006) Finite element and experimental investigation of temperature changes on a twist drill in sequential dry drilling. Int J Adv Manuf Technol 28:680–687
Thangaraj A, Wright PK, Nissle M (1984) New experiments on the temperature distribution in drilling. J Eng Mater Technol 106:242–247
Mills B, Mottishaw TD, Chisholm AWJ (1981) The application of scanning electron microscopy to the study of temperatures and temperature distributions in M2 high speed steel twist drills. CIRP Ann 30:15–20
Reissig L, Völkl R, Mills MJ, Glatzel U (2004) Investigation of near surface structure in order to determine process-temperatures during different machining processes of Ti6A14V. Scr Mater 50:121–126
Koch U, Levi R (1971) Some mechanical and thermal aspects of twist drill performance. CIRP Ann 19:247–254
Saxena U, DeVries M, Wu S-M (1971) Drill temperature distributions by numerical solutions. J Eng Ind 93:1057–1066
Watanabe K, Yokoyama K, lchimiya R (1977) Thermal analysis of the drilling process. Bull Jpn Soc Precis Eng 11:71–77
Fuh K-H, Chen W-C, Liang P-W (1994) Temperature rise in twist drills with a finite element approach. Int Commun Heat Mass Transf 21:345–358
Bono M, Ni J (2006) The location of the maximum temperature on the cutting edges of a drill. Int J Mach Tools Manuf 46:901–907
Ke F, Ni J, Stephenson DA (2005) Continuous chip formation in drilling. Int J Mach Tools Manuf 45:1652–1658
Orfueil M (1987) Electric process heating. Battelle Press, Columbus
Lin GCI, Mathew P, Oxley PLB, Watson AR (1982) Predicting cutting forces for oblique machining conditions. Proc Inst Mech Eng 196:141–148
Berliner EM, Krainov VP (1991) Analytic calculations of the temperature field and heat flows on the tool surface in metal cutting due to sliding friction. Wear 143:379–395
Kalidas S, Kapoor SG, DeVor RE (2002) Influence of thermal effects on hole quality in dry drilling, part 1: a thermal model of workpiece temperatures. J Manuf Sci Eng 124:258–266
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this chapter
Cite this chapter
Shih, A.J., Tai, B.L., Li, R. (2019). Modeling of Drill Temperature and Thermal Stress in Drilling of Titanium Alloys. In: Metal and Bone Drilling - The Thermal Aspects. Springer, Cham. https://doi.org/10.1007/978-3-030-26047-7_3
Download citation
DOI: https://doi.org/10.1007/978-3-030-26047-7_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-26046-0
Online ISBN: 978-3-030-26047-7
eBook Packages: Biomedical and Life SciencesBiomedical and Life Sciences (R0)