Abstract
The effect of repeated use of the chrome-calorizing powder mixture on the thickness and structure of the diffusion coating in the repair of gas turbine engine blades was investigated. The experimental study showed that reuse of the powder mixture results in a change in the mechanism of formation of the diffusion coating. The mechanism of sticking of the powder mixture during deposition of the protective coating on the turbine blades was determined.
This is a preview of subscription content, log in via an institution to check access.
REFERENCES
A. A. Bybin and R. R. Nev’yantseva, “Study of influence of working life on the state of protective coatings in the inner cavity of rotor blades turbine lightweight design,” Uprochnyayushchie Tekhnol. Pokrytiya, No. 11, 3–8 (2016).
R. I. Tkachenko and R. A. Rozanov, “Requirements of the manufacturing technology for single-crystal blades of high-temperature gas turbines,” in New Technological Processes and Reliability of Gas Turbine Engines: Coll. of Papers, Issue 7: Strength Reliability of Working Blades of High-Temperature Turbines (TsIAM, Moscow, 2008), pp. 78–83.
N. V. Abraimov and V. S. Eliseev, Chemical-Heat Treatment of Refractory Steels and Alloys (Intermet Inzhiniring, Moscow, 2001).
A. M. Amouei, G. R. Mirhosseini, A. Jafari, and V. M. Samoilenko, “The influence of process parameters and application of protective coating on mick-restructure nickel super-alloy Inconel-713LC,” Nauchn. Vestn. Mosk. Gos. Tekh. Univ. Grazhdanskoi Aviatsii 19 (3), 80–85 (2016).
N. V. Abraimov, V. V. Lukina, and M. S. Zarypov, “Effect of the composition and structure of Al–Si–Y and Ni–Cr–Al–Y coatings on gas-turbine blades on the service life,” Russ. Metall. 2020, 1404–1410 (2020). https://doi.org/10.1134/s0036029520120022
A. V. Zorichev, T. I. Golovneva, O. A. Parfenovskaya, and V. M. Samoilenko, “Exhaustion of the activity of a powder mixture during its repeated use in protective coating deposition,” Russ. Metall. 2021, 751–756 (2021). https://doi.org/10.1134/S0036029521060276
G. B. Stroganov, V. M. Chepkin, and V. S. Terent’eva, Refractory Coatings for Gas Turbines (Navigator-Ekstra, Moscow, 2000).
K. K. Bakhrunov, “Development of the processes of diffusion saturation of cooled gas turbine blades,” in Proc. 5th Int. Sci.-Tech. Conf. (Ural. Gos. Tekh. Univ.-Ural. Politekh. Inst. im. Pervogo Prezidenta B.N. El’tsina, Ekaterinburg, 2009), Vol. 1, pp. 43–48.
E. G. Ivanov, in Thermodynamic Analysis of Aluminizing and Chrome Aluminizing of Nickel Alloys (VVIA im N.E. Zhukovskogo. NMM Zashchitnye pokrytiya, Moscow, 1975), pp. 15–26.
Funding
This work was supported by ongoing institutional funding. No additional grants to carry out or direct this particular research were obtained.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors of this work declare that they have no conflicts of interest.
Additional information
Translated by Z. Svitanko
Publisher’s Note.
Pleiades Publishing remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Golovneva, T.I., Zorichev, A.V., Pashchenko, G.T. et al. Effect of Reuse of a Chrome-Calorizing Powder Mixture on the Characteristics of a Coating in the Repair of Gas Turbine Blades. Russ. Metall. 2023, 1967–1971 (2023). https://doi.org/10.1134/S003602952312011X
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S003602952312011X