Abstract
Square cyclone was designed for Circulating Fluidized Bed (CFB) boiler technology and was found to be one of the most effective devices for cleaning high-temperature gases. However, the performance of a square cyclone under extreme operating conditions was not thoroughly studied before. The present study fills this knowledge gap by performing a comprehensive numerical simulation that uses computational fluid dynamics (CFD) technique to assess the gas temperature impact on square cyclone performance. The Unsteady Reynolds-Averaged Navier–Stokes equations combined with the Reynolds stress turbulence model (RSTM) were solved to simulate the gas flow. The Lagrangian method was used for particle trajectory analysis. The CFD simulations were implemented over various temperature ranges (from 293 to 700 K). Computational findings showed that particle separation efficiency decreased dramatically with increasing inlet gas temperature because of weaker swirling flow through the cyclone. As the inlet temperature increased, the centrifugal force decreased noticeably, resulting in a larger 50% cut size. The 50% cut size increased by about 10% as the inlet temperature rose from 293 to 700 K at 12 m/s inlet velocity.
Similar content being viewed by others
Abbreviations
- C D :
-
Drag coefficient
- \(\nu\) :
-
Gas kinematic viscosity (m2/s)
- K :
-
Fluctuating kinetic energy (m2/s2)
- \({u}_{i}\) :
-
Gas velocity in i-direction (m/s)
- g i :
-
Gravitational acceleration in i-direction (m/s2)
- \({P}_{f}\) :
-
Fluctuating energy production (m2/s3)
- \(\mu\) :
-
Gas dynamic viscosity (kg/ms)
- ρ :
-
Gas density (kg/m3)
- \({\rho }_{p}\) :
-
Particle density (kg/m3)
- R ij :
-
Reynolds stress tensor
- \({u}_{pi}\) :
-
Particle velocity in i direction (m/s)
- t :
-
Time (s)
- \(\varepsilon\) :
-
Turbulence dissipation rate (m2/s3)
- v :
-
Velocity (m/s)
- \({d}_{p}\) :
-
Particle diameter (μm)
- \({Re}_{p}\) :
-
Relative Reynolds number
- P :
-
Pressure (Pa
References
Dong S, Jiang Y, ** R, Dong K, Wang B (2020) Numerical study of vortex eccentricity in a gas cyclone. Appl Math Model 80:683–701
Misiulia D, Antonyuk S, Andersson AG, Lundström TS (2020) High-efficiency industrial cyclone separator: a CFD study. Powder Technol 364:943–953
Lim KS, Kim HS, Lee KW (2004) Characteristics of the collection efficiency for a cyclone with different vortex finder shapes. J Aerosol Sci 35(6):743–754
Zhang Y, Yu G, ** R, Chen X, Dong K, Jiang Y, Wang B (2020) Investigation into water vapor and flue gas temperatures on the separation capability of a novel cyclone separator. Powder Technol 361:171–178
** R, Keshavarzian E, Dong K, Dong S, Wang B, Kwok K, Zhao M (2020) Numerical study on the effect of the supersaturated vapor on the performance of a gas cyclone. Powder Technol 366:324–336
Caliskan ME, Karagoz I, Avci A, Surmen A (2019) An experimental investigation into the particle classification capability of a novel cyclone separator. Sep Purif Technol 209:908–913
Gao Z, Wang J, Wang J, Mao Y (2019) Time-frequency analysis of the vortex motion in a cylindrical cyclone separator. Chem Eng J 373:1120–1131
Venkatesh S, Sakthivel M, Saranav H, Saravanan N, Rathnakumar M, Santhosh KK (2020) Performance investigation of the combined series and parallel arrangement cyclone separator using experimental and CFD approach. Powder Technol 361:1070–1080
Zhang T, Guo K, Liu C, Li Y, Tao M, Shen C (2018) Experimental and numerical investigations of a dual-stage cyclone separator. Chem Eng Technol 41(3):606–617
Obermair S, Woisetschläger J, Staudinger G (2003) Investigation of the flow pattern in different dust outlet geometries of a gas cyclone by laser Doppler anemometry. Powder Technol 138(2–3):239–251
Fatahian H, Fatahian E, Nimvari ME, Ahmadi G (2021) Novel designs for square cyclone using rounded corner and double-inverted cones shapes. Powder Technol 380:67–79
Fatahian E, Fatahian H (2021) CFD modeling of the effect of dipleg geometry on improving efficiency of a square cyclone. AUT J Mech Eng. https://doi.org/10.22060/ajme.2021.18498.5902
Hosseini E (2020) Performance assessment of a square cyclone influenced by inlet section modifications. J Braz Soc Mech Sci Eng 42(10):1–11
Fu S, Zhou F, Sun G, Yuan H, Zhu J (2021) Performance evaluation of industrial large-scale cyclone separator with novel vortex finder. Adv Powder Technol 32(3):931–939
Safikhani H, Mehrabian P (2016) Numerical study of flow field in new cyclone separators. Adv Powder Technol 27(2):379–387
Balestrin E, Decker RK, Noriler D, Bastos JCSC, Meier HF (2017) An alternative for the collection of small particles in cyclones: experimental analysis and CFD modeling. Sep Purif Technol 184:54–65
Nassaj OR, Toghraie D, Afrand M (2019) Effects of multi inlet guide channels on the performance of a cyclone separator. Powder Technol 356:353–372
Su Y, Zheng A, Zhao B (2011) Numerical simulation of effect of inlet configuration on square cyclone separator performance. Powder Technol 210(3):293–303
Fatahian H, Fatahian E (2020) Improving efficiency of a square cyclone separator using a dipleg–a CFD-based analysis. Iranian J Chem Chem Eng (IJCCE). https://doi.org/10.30492/ijcce.2020.127666.4129
Fatahian E, Fatahian H, Hosseini E, Ahmadi G (2021) A low-cost solution for the collection of fine particles in square cyclone: a numerical analysis. Powder Technol 387:454–465
Raoufi A, Shams M, Kanani H (2009) CFD analysis of flow field in square cyclones. Powder Technol 191(3):349–357
Wasilewski M, Brar LS, Ligus G (2020) Experimental and numerical investigation on the performance of square cyclones with different vortex finder configurations. Sep Purif Technol 239:116588
Venkatesh S, Kumar RS, Sivapirakasam SP, Sakthivel M, Venkatesh D, Arafath SY (2020) Multi-objective optimization, experimental and CFD approach for performance analysis in square cyclone separator. Powder Technol 371:115–129
Fatahian H, Fatahian E, Nimvari ME (2018) Improving efficiency of conventional and square cyclones using different configurations of the laminarizer. Powder Technol 339:232–243
Fatahian H, Hosseini E, Fatahian E (2020) CFD simulation of a novel design of square cyclone with dual-inverse cone. Adv Powder Technol 31(4):1748–1758
Qian F, Zhang J, Zhang M (2006) Effects of the prolonged vertical tube on the separation performance of a cyclone. J Hazard Mater 136(3):822–829
Karagoz I, Kaya F (2007) CFD investigation of the flow and heat transfer characteristics in a tangential inlet cyclone. Int Commun Heat Mass Transfer 34(9–10):1119–1126
Shimizu A, Yokomine T, Nagafuchi T (2004) Development of gas–solid direct contact heat exchanger by use of axial flow cyclone. Int J Heat Mass Transf 47(21):4601–4614
Siadaty M, Kheradmand S, Ghadiri F (2018) Research on the effects of operating conditions and inlet channel configuration on exergy loss, heat transfer and irreversibility of the fluid flow in single and double inlet cyclones. Appl Therm Eng 137:329–340
Shin MS, Kim HS, Jang DS, Chung JD, Bohnet M (2005) A numerical and experimental study on a high efficiency cyclone dust separator for high temperature and pressurized environments. Appl Therm Eng 25(11–12):1821–1835
Gimbun J, Chuah TG, Fakhru’l-Razi, A., & Choong, T. S. (2005) The influence of temperature and inlet velocity on cyclone pressure drop: a CFD study. Chem Eng Process 44(1):7–12
Safikhani H, Akhavan-Behabadi MA, Shams M, Rahimyan MH (2010) Numerical simulation of flow field in three types of standard cyclone separators. Adv Powder Technol 21(4):435–442
Yohana E, Tauviqirrahman M, Yusuf B, Choi KH, Paramita V (2021) Effect of vortex limiter position and metal rod insertion on the flow field, heat rate, and performance of cyclone separator. Powder Technol 377:464–475
Elsayed K, Lacor C (2011) The effect of cyclone inlet dimensions on the flow pattern and performance. Appl Math Model 35(4):1952–1968
Bogodage SG, Leung AY (2015) CFD simulation of cyclone separators to reduce air pollution. Powder Technol 286:488–506
Hamdy O, Bassily MA, El-Batsh HM, Mekhail TA (2017) Numerical study of the effect of changing the cyclone cone length on the gas flow field. Appl Math Model 46:81–97
Nakhaei M, Lu B, Tian Y, Wang W, Dam-Johansen K, Wu H (2020) CFD Modeling of gas–solid cyclone separators at ambient and elevated temperatures. Processes 8(2):228
Launder BE, Reece GJ, Rodi W (1975) Progress in the development of a Reynolds-stress turbulence closure. J Fluid Mech 68(3):537–566
Elsayed K, Lacor C (2010) Optimization of the cyclone separator geometry for minimum pressure drop using mathematical models and CFD simulations. Chem Eng Sci 65(22):6048–6058
Azadi M, Azadi M, Mohebbi A (2010) A CFD study of the effect of cyclone size on its performance parameters. J Hazard Mater 182(1–3):835–841
Wang S, Fang M, Luo Z, Li X, Ni M, Cen K (1999) Instantaneous separation model of a square cyclone. Powder Technol 102(1):65–70
Hoekstra AJ, Derksen JJ, Van Den Akker HEA (1999) An experimental and numerical study of turbulent swirling flow in gas cyclones. Chem Eng Sci 54(13–14):2055–2065
Erol HI, Turgut O, Unal R (2019) Experimental and numerical study of Stairmand cyclone separators: a comparison of the results of small-scale and large-scale cyclones. Heat Mass Transf 55(8):2341–2354
Elsayed K, Lacor C (2012) Modeling and Pareto optimization of gas cyclone separator performance using RBF type artificial neural networks and genetic algorithms. Powder Technol 217:84–99
Morsi SAJ, Alexander AJ (1972) An investigation of particle trajectories in two-phase flow systems. J Fluid Mech 55(2):193–208
Elsayed K, Lacor C (2012) The effect of the dust outlet geometry on the performance and hydrodynamics of gas cyclones. Comput Fluids 68:134–147
Elsayed K, Lacor C (2011) Numerical modeling of the flow field and performance in cyclones of different cone-tip diameters. Comput Fluids 51(1):48–59
Zheng AQ, Su YX, Wan X (2008) Experimental study of a square-shaped separator with different inlet forms. J Eng Thermal Energy Power 23:293–297
Wasilewski M, Brar LS (2019) Effect of the inlet duct angle on the performance of cyclone separators. Sep Purif Technol 213:19–33
Huang AN, Maeda N, Sunada S, Fukasawa T, Yoshida H, Kuo HP, Fukui K (2017) Effect of cold air stream injection on cyclone performance at high temperature. Sep Purif Technol 183:293–303
Parvaz F, Hosseini SH, Elsayed K, Ahmadi G (2018) Numerical investigation of effects of inner cone on flow field, performance and erosion rate of cyclone separators. Sep Purif Technol 201:223–237
Bergman TL, Incropera FP, Lavine AS, Dewitt DP (2011) Introduction to heat transfer. Wiley
Parvaz F, Hosseini SH, Elsayed K, Ahmadi G (2020) Influence of the dipleg shape on the performance of gas cyclones. Sep Purif Technol 233:116000
Brar LS, Elsayed K (2017) Analysis and optimization of multi-inlet gas cyclones using large eddy simulation and artificial neural network. Powder Technol 311:465–483
Babaoğlu NU, Parvaz F, Hosseini SH, Elsayed K, Ahmadi G (2021) Influence of the inlet cross-sectional shape on the performance of a multi-inlet gas cyclone. Powder Technol 384:82–99
Su Y, Mao Y (2006) Experimental study on the gas–solid suspension flow in a square cyclone separator. Chem Eng J 121(1):51–58
Siadaty M, Kheradmand S, Ghadiri F (2017) Study of inlet temperature effect on single and double inlets cyclone performance. Adv Powder Technol 28(6):1459–1473
Wang S, Li H, Wang R, Wang X, Tian R, Sun Q (2019) Effect of the inlet angle on the performance of a cyclone separator using CFD-DEM. Adv Powder Technol 30(2):227–239
Huang AN, Ito K, Fukasawa T, Fukui K, Kuo HP (2018) Effects of particle mass loading on the hydrodynamics and separation efficiency of a cyclone separator. J Taiwan Inst Chem Eng 90:61–67
Author information
Authors and Affiliations
Corresponding author
Additional information
Technical Editor: Monica Carvalho.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Hosseini, E., Fatahian, H., Ahmadi, G. et al. CFD study on the effect of gas temperature on the separation efficiency of square cyclones. J Braz. Soc. Mech. Sci. Eng. 43, 439 (2021). https://doi.org/10.1007/s40430-021-03165-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40430-021-03165-4