Abstract
In the process of underground construction, it is common to spray concrete on the working surface, which will form a concrete-rock composite structure, to achieve the expected reinforcement effect. Compared with pure concrete or rock structures, composite structures have different mechanical properties, energy evolution and damage characteristics. Understanding the dynamic mechanics and damage characteristics of composite structures under impact loads is important to the safety of underground engineering construction. First, dynamic compression tests on different grades of mortar-sandstone composite specimens were carried out by using a Hopkinson pressure bar system to discuss the effect of impact velocities on the mechanical properties and failure modes of composite specimens. The results show that the dynamic peak stress, strain energy density and fragmentation block of the mortar-sandstone composite have an obvious strain rate effect. With an increase in impact velocity, the internal cracks of the sample do not have sufficient time to expand, and the energy absorbed by the sample leads to the continuous initiation of new cracks in the sample, resulting in an increasing damage degree of composite specimens. The increase in mortar strength can significantly increase the peak stress, improve the load-bearing capacity of the sample, and reduce the degree of sample damage. At the same impact velocity, the fragmentation degree of the mortar sample is more severe than that of sandstone, and the mortar sample is broken into powder debris, while the sandstone is broken into fragments. In addition, according to the failure properties of the composite sample, the mortar and sandstone samples are described by different damage models, and the dynamic damage constitutive model of the mortar-sandstone composite is established based on the overlay principle. The dynamic test results were fitted. The research shows that the fitting curves of the model are well fitted with the test curves and that the model accurately reflects the changes in the mechanical parameters of the composite specimens.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Chang X, Lu JY, Wang SY, Wang SR (2018) Mechanical performances of rock-concrete bi-material disks under diametrical compression. International Journal of Rock Mechanics and Mining Sciences 104:71–77, DOI: https://doi.org/10.1016/j.ijrmms.2018.02.008
Chen M, Wang H, Qi M, Li Y, Wang SH, Wang EL (2020) Experimental study on dynamic compressive properties of composite layers of rock and steel fiber reinforced concrete. Chinese Journal of Rock Mechanics and Engineering 39(6):1222–1230, DOI: https://doi.org/10.13722/j.cnki.jrme.2019.1221 (in Chinese)
Cui T, He HX, Yan WM, Zhou DX (2020) Compression damage constitutive model of hybrid fiber reinforced concrete and its experimental verification. Construction and Building Materials 264:120026, DOI: https://doi.org/10.1016/j.conbuildmat.2020.120026
Cuong LT, Nguyen KDD, Hoang LM, Sang TT, Phung VP, Abdel WM (2022) Nonlocal strain gradient IGA numerical solution for static bending, free vibration and buckling of sigmoid FG sandwich nanoplate. Physica B: Condensed Matter 631:413726, DOI: https://doi.org/10.1016/j.physb.2022.413726
Deng Y, Chen M, ** Y, Zou DW (2016) Theoretical analysis and experimental research on the energy dissipation of rock crushing based on fractal theory. Journal of Natural Gas Science and Engineering 33:231–239, DOI: https://doi.org/10.1016/j.jngse.2016.05.020
Dong W, Wu ZM, Zhang BS, She J (2021) Study on shear-softening sonstitutive law of rock-concrete interface. Rock Mechanics and Rock Engineering 54:4677–4694, DOI: https://doi.org/10.1007/s00603-021-02536-6
Fan HB, Fan ZH, Lu YZ (2005) Identification of rheological constitutive relation of engineering material based on overla-yer model. Chinese Journal of Rock Mechanics and Engineering 24(5):768–773 (in Chinese)
Gong FQ, Hao Y, Yong L (2018) The effect of high loading rate on the behaviour and mechanical properties of coal-rock combined body. Shock and Vibration 2018:4374530, DOI: https://doi.org/10.1155/2018/4374530
Gutierrez JG, Senent S, Melentijevic S, Jimenez R (2018) Distinct element method simulations of rock-concrete interfaces under different boundary conditions. Engineering Geology 240:123–139, DOI: https://doi.org/10.1016/j.enggeo.2018.04.017
Keshavarz A, Ghajar R (2019) Effect of isotropic and anisotropic damage and plasticity on ductile crack initiation. International Journal of Damage Mechanics 28(6):918–942, DOI: https://doi.org/10.1177/1056789518802625
Li CJ, Xu Y, Chen PY, Li HL, Lou PJ (2020) Dynamic mechanical properties and fragment fractal characteristics of fractured coal-rock-like combined bodies in split hopkinson pressure bar tests. Natural Resources Research 29(5):3179–3195, DOI: https://doi.org/10.1007/s11053-020-09656-w
Li DY, Han ZY, Zhu QQ, Zhang Y, Ranjith PG (2019a) Stress wave propagation and dynamic behavior of red sandstone with single bonded planar joint at various angles. International Journal of Rock Mechanics and Mining Sciences 117:162–170, DOI: https://doi.org/10.1016/j.ijrmms.2019.03.011
Li CJ, Xu Y, Zhang YT, Li HL (2019b) Study on energy evolution and fractal characteristics of cracked coal-rock-like combined body under impact loading. Chinese Journal of Rock Mechanics and Engineering 38(11):2231–2241, DOI: https://doi.org/10.13722/j.cnkijrme.2019.0446 (in Chinese)
Liu Y, Huang D, Zhao B, Wang C, Cen D (2020) Nonlinear creep behavior and viscoelastic-plastic constitutive model of rock-concrete composite mass. Advances in Civil Engineering 2020:9059682, DOI: https://doi.org/10.1155/2020/9059682
Ma (2018) Constitutive models of half-homogeneous sandstone based on damage evolution. Journal of Yangtze River Scientific Research Institute 35(6):86–91, DOI: https://doi.org/10.11988/ckyyb.20160787
Meng XR, Peng R, Zhao G, Li YM (2017) Roadway engineering mechanical properties and roadway structural instability mechanisms in deep wells. KSCE Journal of Civil Engineering 22(5):1954–1966, DOI: https://doi.org/10.1007/s12205-017-1298-y
Mohammad Z (2021) Dynamic stability analysis of rock tunnels subjected to impact loading with varying UCS. Geomechanics and Engineering 24(6):505–518, DOI: https://doi.org/10.12989/gae.2021.24.6.505
Moradi M, Bagherieh AR, Esfahani MR (2020) Constitutive modeling of steel fiber-reinforced concrete. International Journal of Damage Mechanics 29(3):388–412, DOI: https://doi.org/10.1177/1056789519851159
Phung VP, Thai CH, Nguyen XH, Abdel WM (2019) An isogeometric approach of static and free vibration analyses for porous FG nanoplates. European Journal of Mechanics/A Solids 78:103851, DOI: https://doi.org/10.1016/j.euromechsol.2019.103851
Rabczuk T, Belytschko T (2004) Cracking particles: A simplified meshfree method for arbitrary evolving cracks. International Journal for Numerical Methods in Engineering 61(13):2316–2343, DOI: https://doi.org/10.1002/nme.1151
Rabczuk T, Zi G, Bordas S, Nguyen-Xuan H (2010) A simple and robust three-dimensional cracking-particle method without enrichment. Computer Methods in Applied Mechanics and Engineerin 199(37): 2437–2455, DOI: https://doi.org/10.1016/j.cma.2010.03.031
Rong H, Wang YJ, Zhao XY, She J (2019) Research on fracture characteristics of rock-concrete interface with different roughness. Engineering Mechanics 36(10):96–103, DOI: https://doi.org/10.6052/j.issn.1000-4750.2018.09.0485 (in Chinese)
Selcuk L, Asma D (2019) Experimental investigation of the rock-concrete bi materials influence of inclined interface on strength and failure behavior. International Journal of Rock Mechanics and Mining Sciences 123:104119, DOI: https://doi.org/10.1016/j.ijrmms.2019.104119
Shakeri J, Asadizadeh M, Babanouri N, Nowak S, Sherizah T (2022) The evolution of dynamic energy during drop hammer testing of Brazilian disk with non-persistent joints: An extensive experimental investigation. Theoretical and Applied Fracture Mechanics 117: 103162, DOI: https://doi.org/10.1016/j.tafmec.2021.103162
Teng JY, Tang JX, Wang JB, Zhang YN (2018) The evolution law of the damage of bedded composite rock and its fractal characteristics. Chinese Journal of Rock Mechanics and Engineering 37(S1):3263–3278, DOI: https://doi.org/10.13722/j.cnki.jrme.2016.1397 (in Chinese)
Thakur A, Senthil K, Singh AP (2022) Evaluation of concrete bricks with crumb rubber and polypropylene fibres under impact loading. Construction and Building Materials 315:125752, DOI: https://doi.org/10.1016/j.conbuildmat.2021.125752
Wang MN, Hu YP, Tong JJ, Wang QL, Wang YC, Dong CY (2019) Experimental study on shear mechanical properties and thermal damage model of shotcrete-rock interfaces under variable high temperatures. Chinese Journal of Rock Mechanics and Engineering 38(1):63–75, DOI: https://doi.org/10.13722/j.cnki.jrme.2018.0852 (in Chinese)
Wang L, Su HM, Chen SG, Qin Y (2020) Nonlinear dynamic constitutive model of frozen sandstone based on weibull distribution. Advances in Cicil Engineering 2020:6439207, DOI: https://doi.org/10.1155/2020/6439207
Wang F, Qian YJ, Xu JY, Li ZW (2017) Analysis of dynamic damage constitutive model for concrete exposed to high temperature. Journal of Southwest Jiaotong University 52(6):1075–1081, DOI: https://doi.org/10.3969/j.issn.0258-2724.2017.06.006 (in Chinese)
Wang JG, Zuo T, Li XL, Tao ZH, Ma J (2021) Study on the fractal characteristics of the pomegranate biotite schist under impact loading. Geofluids 2021:1570160, DOI: https://doi.org/10.1155/2021/1570160
**e BJ, Yan Z (2019) Dynamic mechanical constitutive model of combined coal-rock mass based on overlay model. Journal of China Coal Society 44(2):463–472, DOI: https://doi.org/10.13225/j.cnki.jccs.2018.1007 (in Chinese)
**e HP, Wang JN, Qan PG (1996) Fractal characters ofmicropore evolution in marbles. Physics Letters A 218(3):275–280, DOI: https://doi.org/10.1016/0375-9601(96)00390-8
Yang RS, Li WY, Fang SZ, Zhu Y, Li YL (2019) Experimental study on impact dynamic characteristics of layered composite rocks. Chinese Journal of Rock Mechanics and Engineering 38(9):1747–1757, DOI: https://doi.org/10.13722/j.cnki.jrme.2019.0021 (in Chinese)
Ye L, Dong YX, Zhao HP (2005) Stress wave propaga-tion in multi-layered composite media. National conference on engineering structure safety protection, October 17–19, Nan**g, JS, China
Yuan WY, Dong W, Zhang BS, Zhong H (2021) Investigations on fracture properties and analytical solutions of fracture parameters at rock-concrete interface. Construction and Building Materials 300: 124040, DOI: https://doi.org/10.1016/J.conbuildmat.2021.124040
Zhang YM, Gao ZR, Li YY, Zhuang XY (2020) On the crack opening and energy dissipation in a continuum based disconnected crack model. Finite Elements in Analysis & Design 170:103333, DOI: https://doi.org/10.1016/j.finel.2019.103333
Zhang MT, Wang W, Wang QZ, Zhang SY (2021) Dynamic failure process and strain-damage evolution law of sandstone based on SHPB experiments. Explosion and Shock Waves 41(9):40–53, DOI: https://doi.org/10.11883/bzycj-2020-0288 (in Chinese)
Zhang YM, Mang HA (2020) Global cracking elements: a novel tool for galerkin-based approaches simulating quasi-brittle fracture. International Journal for Numerical Methods in Engineering 121(11):462–2480, DOI: https://doi.org/10.1002/nme.6315
Zhang YM, Huang JG, Yuan Y, Mang HA (2021) Cracking elements method with a dissipation-based arc-length approach. Finite Elements in Analysis & Design 195:103573, DOI: https://doi.org/10.1016/J.FINEL.2021.103573
Zhang YM, Zhuang XY (2018) Cracking elements: A self-propagating strong discontinuity embedded approach for quasi-brittle fracture. Finite Elements in Analysis & Design 144:84–100, DOI: https://doi.org/10.1016/j.finel.2017.10.007
Zhang YM, Zhuang XY (2019) Cracking elements method for dynamic brittle fracture. Theoretical and Applied Fracture Mechanics 102:1–9, DOI: https://doi.org/10.1016/j.tafmec.2018.09.015
Zhao BY, Liu Y, Huang TZ, Wang XP (2019) Experimental study on strength and deformation characteristics of rock-concrete composite specimens under compressive condition. Geotechnical and Geological Engineering 37(4):2693–2706, DOI: https://doi.org/10.1007/s10706-018-00787-9
Zhao BY, Liu Y, Liu DY, Huang W, Wang XP, Yu GB, Liu S (2020) Research on the influence of contact surface constraint on mechanical properties of rock-concrete composite specimens under compressive loads. Frontiers of Structural and Civil Engineering 14(2):1–9, DOI: https://doi.org/10.1007/s11709-019-0594-7
Zhao Y, Shen MX, Bi J, Wang CL, Yang YT, Du B, Ning L (2022) Experimental study on physical and mechanical characteristics of rock-concrete combined body under complex stress conditions. Construction and Building Materials 324:126647, DOI: https://doi.org/10.1016/J.conbuildmat.2022.126647
Zhou J, Xu WS, Zhao GM, Meng XR, Li YM, Wu XK, Li YG, Cheng X (2022) Energy evolution law and fractal characteristics of different rock specimen sizes on dynamic compression. Geofluids 2022:5339603, DOI: https://doi.org/10.1155/2022/5339603
Zhou ZL, Lu JY, Cai X (2020) Static and dynamic tensile behavior of rock-concrete bi-material disc with different interface inclinations. Construction and Building Materials 256:119424, DOI: https://doi.org/10.1016/j.conbuildmat.2020.119424
Zhu JB, Bao WY, Peng Q, Deng XF (2020) Influence of substrate properties and interfacial roughness on static and dynamic tensile behaviour of rock-shotcrete interface from macro and micro views. International Journal of Rock Mechanics and Mining Sciences 132:104350, DOI: https://doi.org/10.1016/j.ijrmms.2020.104350
Acknowledgments
This research is financially supported by the National Natural Science Foundation of China (grant numbers 51934001).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, Q., Zhao, Td., Huang, C. et al. Dynamic and Damage Characteristics of Mortar Composite under Impact Load. KSCE J Civ Eng 27, 1383–1395 (2023). https://doi.org/10.1007/s12205-023-1709-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-023-1709-1