SpringerLink
Log in

Surface Properties of Additively Manufactured 316L Steel Subjected to Ultrasonic Rolling

  • Original Research Article
  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

Abstract

The ultrasonic rolling (UR) was applied to strengthen the surface properties of the laser additive manufactured 316L stainless steel (LAMed-316SS). The wear resistance and corrosion resistance of LAMed-316SS were researched to reveal the surface strengthening mechanism of UR. The results indicated that the surface integrity of LAMed-316SS was reconstructed by UR due to the severe plastic deformation with the grain refined, the surface roughness reached 0.051 μm, the surface microhardness increased to 319 HV0.05, and the compressive residual stress induced up to − 176 MPa. After UR, the wear mechanism of LAMed-316SS was changed into the delamination wear from the abrasive wear and adhesive wear. In virtue of the reconstructed surface integrity, the wear resistance and corrosion resistance of LAMed-316SS were enhanced with the wear rate, friction coefficient, and corrosion current density decreased by 14.8%, 18.6%, and 40.5%, and the polarization resistance increased by 33.9%, individually.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
EUR 32.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or Ebook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price includes VAT (Germany)

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14

Similar content being viewed by others

References

  1. S. Singh, S. Ramakrishna and R. Singh, Material Issues in Additive Manufacturing: A Review, J. Manuf. Process., 2017, 25, p 185–200. https://doi.org/10.1016/j.jmapro.2016.11.006

    Article  Google Scholar 

  2. H. Lee, C.H.J. Lim, M.J. Low, N. Tham, V.M. Murukeshan and Y.-J. Kim, Lasers in Additive Manufacturing: A Review, Int. J. Precis Eng Manuf-Green Technol., 2017, 4, p 307–322. https://doi.org/10.1007/s40684-017-0037-7

    Article  Google Scholar 

  3. M.S.F. de Lima and S. Sankaré, Microstructure and Mechanical Behavior of Laser Additive Manufactured AISI 316 Stainless Steel Stringers, Mater. Des., 2014, 55, p 526–532. https://doi.org/10.1016/j.matdes.2013.10.016

    Article  CAS  Google Scholar 

  4. B. He, C. Bi, X. Li, W. Wang and G. Yang, Residual Stresses and Deformations of Laser Additive Manufactured Metal Parts: A Review, Int. J. Mater. Form., 2022 https://doi.org/10.1007/s12289-022-01729-w

    Article  Google Scholar 

  5. T.H. Sibisi, M.B. Shongwe, L.C. Tshabalala and I. Mathoho, LAM Additive Manufacturing: A Fundamental Review on Mechanical Properties, Common Defects, Dominant Processing Variables, and Its Applications, Int. J. Adv. Manuf. Technol., 2023, 128, p 2847–2861. https://doi.org/10.1007/s00170-023-12139-w

    Article  Google Scholar 

  6. S. Santa-aho, M. Kiviluoma, T. Jokiaho, T. Gundgire, M. Honkanen, M. Lindgren and M. Vippola, Additive Manufactured 316L Stainless-Steel Samples: Microstructure, Residual Stress and Corrosion Characteristics after Post-Processing, Metals., 2021 https://doi.org/10.3390/met11020182

    Article  Google Scholar 

  7. X.H. Zhao, D.W. Nie, D.S. Xu, Y. Liu and C.H. Hu, Effect of Gradient Nanostructures on Tribological Properties of 316L Stainless Steel with High Energy Ion Implantation Tungsten Carbide, Tribol. Trans., 2019, 62, p 189–197. https://doi.org/10.1080/10402004.2018.1508797

    Article  CAS  Google Scholar 

  8. O. Elsayed, V.S.K. Adapa, S. Kersten, D. Vaughan, C. Masuo, M.J. Kim, T. Feldhausen, C. Saldana and T. Kurfess, Effects of Lead and Lean in Multi-Axis Directed Energy Deposition, Int. J. Adv. Manuf. Technol., 2023, 125, p 5119–5134. https://doi.org/10.1007/s00170-023-11085-x

    Article  Google Scholar 

  9. T. Tancogne-Dejean, C.C. Roth and D. Mohr, Rate-Dependent Strength and Ductility of Binder Jetting 3D-Printed Stainless Steel 316L: Experiments and Modeling, Int. J. Mech. Sci., 2021 https://doi.org/10.1016/j.ijmecsci.2021.106647

    Article  Google Scholar 

  10. J.A. Stull, M.A. Hill, T.J. Lienert, J. Tokash, K.R. Bohn and D.E. Hooks, Corrosion Characteristics of Laser-Engineered Net Sha** Additively-Manufactured 316L Stainless Steel, JOM, 2018, 70, p 2677–2683. https://doi.org/10.1007/s11837-018-3123-6

    Article  CAS  Google Scholar 

  11. S. Prochaska and O. Hildreth, Effect of Chemically Accelerated Vibratory Finishing on The Corrosion Behavior of Laser Powder Bed Fusion 316L Stainless Steel, J. Mater. Process. Technol., 2022 https://doi.org/10.1016/j.jmatprotec.2022.117596

    Article  Google Scholar 

  12. U. Gençoğlu, G. Kaya, T.O. Ergüder, İ Hacısalihoğlu and F. Yıldız, Investigation of The Structural and Tribological Properties of 316L Stainless Steel Manufactured Using Variable Production Parameters by Selective Laser Melting, J. Mater. Eng. Perform., 2022, 31, p 3688–3703. https://doi.org/10.1007/s11665-021-06507-4

    Article  CAS  Google Scholar 

  13. D. Kong, C. Dong, X. Ni and X. Li, Corrosion of Metallic Materials Fabricated by Selective Laser Melting, NPJ Mater. Degrad., 2019 https://doi.org/10.1038/s41529-019-0086-1

    Article  Google Scholar 

  14. Q. Xu, J. Zhou, D. Jiang, X. Yang and Z. Qiu, Improved Low-Temperature Mechanical Properties of FH36 Marine Steel after Ultrasonic Surface Rolling Process, J. Alloy. Compd., 2023 https://doi.org/10.1016/j.jallcom.2022.168401

    Article  Google Scholar 

  15. Y. Meng, J. Deng, Y. Lu, S. Wang, J. Wu and W. Sun, Fabrication of AlTiN Coatings Deposited on The Ultrasonic Rolling Textured Substrates for Improving Coatings Adhesion Strength, Appl. Surf. Sci., 2021 https://doi.org/10.1016/j.apsusc.2021.149394

    Article  Google Scholar 

  16. Z. Liu, C. Gao, X. Liu, R. Liu and Z. **ao, Improved Surface Integrity of Ti6Al4V Fabricated by Selective Electron Beam Melting Using Ultrasonic Surface Rolling Processing, J. Mater. Process. Technol., 2021 https://doi.org/10.1016/j.jmatprotec.2021.117264

    Article  Google Scholar 

  17. Y. Meng, J. Deng, Y. Zhang, S. Wang, X. Li, H. Yue and D. Ge, Tribological Properties of Textured Surfaces Fabricated on AISI 1045 Steels by Ultrasonic Surface Rolling under Dry Reciprocating Sliding, Wear., 2020 https://doi.org/10.1016/j.wear.2020.203488

    Article  Google Scholar 

  18. P.F. Wang and Z. Han, Friction and Wear Behaviors of A Gradient Nano-Grained AISI 316L Stainless Steel under Dry and Oil-Lubricated Conditions, J. Mater. Sci. Technol., 2018, 34, p 1835–1842. https://doi.org/10.1016/j.jmst.2018.01.013

    Article  CAS  Google Scholar 

  19. Z. Liu, X. Liu, R. Liu, Z. **ao and J. Sanderson, Improved Rolling Contact Fatigue Performance of Selective Electron Beam Melted Ti6Al4V with The As-Built Surface Using Induction-Heating Assisted Ultrasonic Surface Rolling Process, Appl. Surf. Sci., 2023 https://doi.org/10.1016/j.apsusc.2022.155467

    Article  Google Scholar 

  20. Z. Cui, Y. Mi, D. Qiu, P. Dong, Z. Qin, D. Gong and W. Li, Microstructure and Mechanical Properties of Additively Manufactured CrMnFeCoNi High-Entropy Alloys after Ultrasonic Surface Rolling Process, J. Alloys Compd., 2021 https://doi.org/10.1016/j.jallcom.2021.161393

    Article  Google Scholar 

  21. X. Xu, D. Liu, X. Zhang, C. Liu and D. Liu, Mechanical and Corrosion Fatigue Behaviors of Gradient Structured 7B50-T7751 Aluminum Alloy Processed via Ultrasonic Surface Rolling, J. Mater. Sci. Technol., 2020, 40, p 88–98. https://doi.org/10.1016/j.jmst.2019.08.030

    Article  CAS  Google Scholar 

  22. G. Xu, C. Wang, Q. Li, X. Zhang, Z. Zhu, T. Liang and B. Yang, Effects of Ultrasonic Rolling on Surface Performance of 7B85-T6 Alloy, Mater. Manuf. Process., 2020, 35, p 250–257. https://doi.org/10.1080/10426914.2020.1718701

    Article  CAS  Google Scholar 

  23. C. Li, R. Zhu, X. Zhang, P. Huang, X. Wang and X. Wang, Impact of Surface Ultrasonic Rolling on Cavitation Erosion Behavior of 304 Stainless Steel, Surf. Coat. Technol., 2020 https://doi.org/10.1016/j.surfcoat.2019.125280

    Article  Google Scholar 

  24. K. Zheng, Y. Lin, J. Cai and C. Lei, Corrosion Resistance and Tribological Properties of Laser Cladding Layer of H13 Die Steel Strengthened by Ultrasonic Rolling, Chin. J. Mech. Eng., 2022 https://doi.org/10.1186/s10033-022-00810-4

    Article  Google Scholar 

  25. X. Gao, B. Li and C. Jiang, The Critical Assessment for The Fatigue Limit of Nanocrystallized Surface with Micro-Notches Obtained by Ultrasonic Surface Rolling Processing, Int. J. Fatigue, 2021 https://doi.org/10.1016/j.ijfatigue.2020.105988

    Article  Google Scholar 

  26. Q. Zhang, Z. Hu, W. Su, H. Zhou, C. Liu, Y. Yang and X. Qi, Microstructure and Surface Properties of 17–4PH Stainless Steel by Ultrasonic Surface Rolling Technology, Surf. Coat., 2017, 321, p 64–73. https://doi.org/10.1016/j.surfcoat.2017.04.052

    Article  CAS  Google Scholar 

  27. X. Zhao, K. Liu, D. Xu, Y. Liu and C. Hu, Effects of Ultrasonic Surface Rolling Processing and Subsequent Recovery Treatment on the Wear Resistance of AZ91D Mg Alloy, Materials., 2020 https://doi.org/10.3390/ma13245705

    Article  Google Scholar 

  28. D. Liu, D. Liu, M. Guagliano, X. Xu, K. Fan and S. Bagherifard, Contribution of Ultrasonic Surface Rolling Process to the Fatigue Properties of TB8 Alloy with Body-Centered Cubic Structure, J. Mater. Sci. Technol., 2021, 61, p 63–74. https://doi.org/10.1016/j.jmst.2020.05.047

    Article  CAS  Google Scholar 

  29. J. Han, C. Wang, Y. Song, Z. Liu, J. Sun and J. Zhao, Simultaneously Improving Mechanical Properties and Corrosion Resistance of As-Cast AZ91 Mg Alloy by Ultrasonic Surface Rolling, Int. J. Miner. Metall. Mater., 2022, 29, p 1551–1558. https://doi.org/10.1007/s12613-021-2294-2

    Article  CAS  Google Scholar 

  30. Y. Liu, J. Sun, Y. Fu, B. Xu, B. Li, S. Xu, P. Huang, J. Cheng, Y. Han, J. Han and G. Wu, Tuning Strength-Ductility Combination on Selective Laser Melted 316L Stainless Steel through Gradient Heterogeneous Structure, Addit. Manuf., 2021 https://doi.org/10.1016/j.addma.2021.102373

    Article  Google Scholar 

  31. W. Ting, W. Dongpo, L. Gang, G. Baoming and S. Ningxia, Investigations on the Nanocrystallization of 40Cr Using Ultrasonic Surface Rolling Processing, Appl. Surf. Sci., 2008, 255, p 1824–1829. https://doi.org/10.1016/j.apsusc.2008.06.034

    Article  CAS  Google Scholar 

  32. Y.M. Wang, T. Voisin, J.T. McKeown, J. Ye, N.P. Calta, Z. Li, Z. Zeng, Y. Zhang, W. Chen, T.T. Roehling, R.T. Ott, M.K. Santala, P.J. Depond, M.J. Matthews, A.V. Hamza and T. Zhu, Additively Manufactured Hierarchical Stainless Steels with High Strength and Ductility, Nat. Mater., 2018, 17, p 63–71. https://doi.org/10.1038/nmat5021

    Article  CAS  Google Scholar 

  33. D. Herzog, V. Seyda, E. Wycisk and C. Emmelmann, Additive Manufacturing of Metals, Acta Mater., 2016, 117, p 371–392. https://doi.org/10.1016/j.actamat.2016.07.019

    Article  CAS  Google Scholar 

  34. S. Yin, C. Chen, X. Yan, X. Feng, R. Jenkins, P. O’Reilly, M. Liu, H. Li and R. Lupoi, The Influence of Aging Temperature and Aging Time on The Mechanical and Tribological Properties of Selective Laser Melted Maraging 18Ni-300 Steel, Addit. Manuf., 2018, 22, p 592–600. https://doi.org/10.1016/j.addma.2018.06.005

    Article  CAS  Google Scholar 

  35. D. Kong, C. Dong, S. Wei, X. Ni, L. Zhang, R. Li, L. Wang, C. Man and X. Li, About Metastable Cellular Structure in Additively Manufactured Austenitic Stainless Steels, Addit. Manuf., 2021 https://doi.org/10.1016/j.addma.2020.101804

    Article  Google Scholar 

  36. G. Li, W. Zhang, Y. Liu, X. **ao, D. Song and Z. Xu, Effect of Ultrasonic Surface Rolling on Fretting Friction and Wear Properties of Heat-Treated Hot Isostatic Pressing Ti-6Al-4V Alloy, J. Mater. Eng. Perform., 2021, 31, p 3859–3871. https://doi.org/10.1007/s11665-021-06483-9

    Article  CAS  Google Scholar 

  37. X. Liu, S. Jiang, J. Lu, J. Wei, D. Wei and F. He, The Dual Effect of Grain Size on The Strain Hardening Behaviors of Ni-Co-Cr-Fe High Entropy Alloys, J. Mater. Sci. Technol., 2022, 131, p 177–184. https://doi.org/10.1016/j.jmst.2022.06.001

    Article  CAS  Google Scholar 

  38. S. Qu, X.H. An, H.J. Yang, C.X. Huang, G. Yang, Q.S. Zang, Z.G. Wang, S.D. Wu and Z.F. Zhang, Microstructural Evolution and Mechanical Properties of Cu–Al Alloys Subjected to Equal Channel Angular Pressing, Acta Mater., 2009, 57, p 1586–1601. https://doi.org/10.1016/j.actamat.2008.12.002

    Article  CAS  Google Scholar 

  39. K. Lu and J. Lu, Nanostructured Surface Layer on Metallic Materials Induced by Surface Mechanical Attrition Treatment, Mater. Sci. Eng. A, 2004, 375–377, p 38–45. https://doi.org/10.1016/j.msea.2003.10.261

    Article  CAS  Google Scholar 

  40. H. Li, E. Hsu, J. Szpunar, H. Utsunomiya and T. Sakai, Deformation Mechanism and Texture and Microstructure Evolution during High-Speed Rolling of AZ31B Mg Sheets, J. Mater. Sci., 2008, 43, p 7148–7156. https://doi.org/10.1007/s10853-008-3021-3

    Article  CAS  Google Scholar 

  41. M. Calcagnotto, D. Ponge, E. Demir and D. Raabe, Orientation Gradients and Geometrically Necessary Dislocations in Ultrafine Grained Dual-Phase Steels Studied by 2D and 3D EBSD, Mater. Sci. Eng. A, 2010, 527, p 2738–2746. https://doi.org/10.1016/j.msea.2010.01.004

    Article  CAS  Google Scholar 

  42. Z. Wang, X. Liu, Q. Yuan, R. Chen, J. He, J. Qin, Y. Huang and H. Zhao, Warm Deformation and Dynamic Strain Aging of a Nb-Cr Microalloyed Low-Carbon Steel, Metall. Mater. Trans. A, 2020, 51, p 4623–4631. https://doi.org/10.1007/s11661-020-05855-5

    Article  CAS  Google Scholar 

  43. M. Wen, G. Liu, J.-F. Gu, W.-M. Guan and J. Lu, Dislocation Evolution in Titanium during Surface Severe Plastic Deformation, Appl. Surf. Sci., 2009, 255, p 6097–6102. https://doi.org/10.1016/j.apsusc.2009.01.048

    Article  CAS  Google Scholar 

  44. Y. Cao, S. Ni, X. Liao, M. Song and Y. Zhu, Structural Evolutions of Metallic Materials Processed by Severe Plastic Deformation, Mater. Sci. Eng. R-Rep., 2018, 133, p 1–59. https://doi.org/10.1016/j.mser.2018.06.001

    Article  Google Scholar 

  45. C. Liu, D. Liu, X. Zhang, G. He, X. Xu, N. Ao, A. Ma and D. Liu, On The Influence of Ultrasonic Surface Rolling Process on Surface Integrity and Fatigue Performance of Ti-6Al-4V Alloy, Surf. Coat. Technol., 2019, 370, p 24–34. https://doi.org/10.1016/j.surfcoat.2019.04.080

    Article  CAS  Google Scholar 

  46. H. Liu, J. Liu, P. Chen and H. Yang, Microstructure and High Temperature Wear Behaviour of in-Situ TiC Reinforced AlCoCrFeNi-Based High-Entropy Alloy Composite Coatings Fabricated by Laser Cladding, Opt. Laser Technol., 2019, 118, p 140–150. https://doi.org/10.1016/j.optlastec.2019.05.006

    Article  CAS  Google Scholar 

  47. F. Wang, X. Yan, L. Liu, M. Nastasi, Y. Lu and B. Cui, Surface Strengthening of Single-Crystal Alumina by High-Temperature Laser Shock Peening, Mater. Res. Lett., 2020, 9, p 155–161. https://doi.org/10.1080/21663831.2020.1862933

    Article  CAS  Google Scholar 

  48. Y.S. Li, N.R. Tao and K. Lu, Microstructural Evolution and Nanostructure Formation in Copper during Dynamic Plastic Deformation at Cryogenic Temperatures, Acta Mater., 2008, 56, p 230–241. https://doi.org/10.1016/j.actamat.2007.09.020

    Article  CAS  Google Scholar 

  49. A. Barari, H.A. Kishawy, F. Kaji and M.A. Elbestawi, On The Surface Quality of Additive Manufactured Parts, Int. J. Adv. Manuf. Technol., 2016, 89, p 1969–1974. https://doi.org/10.1007/s00170-016-9215-y

    Article  Google Scholar 

  50. S. Qu, Z. Wu, Y. Zhang, T. Wang, X. Li, J. Geng and Y. Deng, Effect of Ultrasonic Surface Rolling on Friction and Wear Properties of 20CrMoH Stell, Surf. Technol., 2022, 51, p 211–222. https://doi.org/10.16490/j.cnki.issn.1001-3660.2022.02.020

    Article  Google Scholar 

  51. A.F. Yetim, H. Tekdir, K. Turalioglu, M. Taftali and T. Yetim, Tribological Behavior of Plasma-sprayed Yttria-Stabilized Zirconia Thermal Barrier Coatings on 316L Stainless Steel under High-Temperature Conditions, Materials Letters., 2023 https://doi.org/10.1016/j.matlet.2023.133873

    Article  Google Scholar 

  52. H.X. Zhang, J.J. Dai, C.X. Sun and S.Y. Li, Microstructure and Wear Resistance of TiAlNiSiV High-Entropy Laser Cladding Coating on Ti-6Al-4V, J. Mater. Process. Technol., 2020 https://doi.org/10.1016/j.jmatprotec.2020.116671

    Article  Google Scholar 

  53. P.K. Rai, S. Shekhar and K. Mondal, Effects of Grain Size Gradients on The Fretting Wear of A Specially-Processed Low Carbon Steel Against AISI E52100 Bearing Steel, Wear, 2018, 412–413, p 1–13. https://doi.org/10.1016/j.wear.2018.07.014

    Article  CAS  Google Scholar 

  54. P. Zhang and Z. Liu, On Sustainable Manufacturing of Cr-Ni alloy Coatings by Laser Cladding and High-Efficiency Turning Process Chain and Consequent Corrosion Resistance, J. Clean. Prod., 2017, 161, p 676–687. https://doi.org/10.1016/j.jclepro.2017.05.169

    Article  CAS  Google Scholar 

  55. Z. Xu, H. Zhang, X. Du, Y. He, H. Luo, G. Song, L. Mao, T. Zhou and L. Wang, Corrosion Resistance Enhancement of CoCrFeMnNi High-Entropy Alloy Fabricated by Additive Manufacturing, Corrosion Sci., 2020 https://doi.org/10.1016/j.corsci.2020.108954

    Article  Google Scholar 

  56. T. Yetim, H. Tekdir, M. Taftalı, K. Turalıoğlu and A.F. Yetim, Synthesis and Characterisation of Single and Duplex ZnO/TiO2 Ceramic Films on Additively Manufactured Bimetallic Material of 316L Stainless Steel and Ti6Al4V, Surf. Topogr. Metrol. Prop., 2023 https://doi.org/10.1088/2051-672X/accf6c

    Article  Google Scholar 

  57. W. Zhang, K. Fang, Y. Hu, S. Wang and X. Wang, Effect of Machining-Induced Surface Residual Stress on Initiation of Stress Corrosion Cracking in 316 Austenitic Stainless Steel, Corrosion Sci., 2016, 108, p 173–184. https://doi.org/10.1016/j.corsci.2016.03.008

    Article  CAS  Google Scholar 

  58. P. Qin, L.Y. Chen, Y.J. Liu, Z. Jia, S.X. Liang, C.H. Zhao, H. Sun and L.C. Zhang, Corrosion and Passivation Behavior of Laser Powder Bed Fusion Produced Ti-6Al-4V in Static/Dynamic NaCl Solutions with Different Concentrations, Corrosion Sci., 2021 https://doi.org/10.1016/j.corsci.2021.109728

    Article  Google Scholar 

  59. Q. Xu, D. Jiang, J. Zhou, Z. Qiu and X. Yang, Enhanced Corrosion Resistance of Laser Additive Manufactured 316L Stainless Steel by Ultrasonic Surface Rolling Process, Surf. Coat. Technol., 2023 https://doi.org/10.1016/j.surfcoat.2022.129187

    Article  Google Scholar 

  60. Q. Xu, X. Yang, J. Liu, D. Jiang and Z. Qiu, Improved Corrosion Resistance of 42CrMo4 Steel by Reconstructing Surface Integrity Using Ultrasonic Surface Rolling Process, Mater. Today Commun., 2023 https://doi.org/10.1016/j.mtcomm.2023.105932

    Article  Google Scholar 

Download references

Acknowledgments

This study was supported by the National Natural Science Foundation of China (No.52001048).

Author information

Authors and Affiliations

  1. Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian, 116026, People’s Republic of China

    Qingzhong Xu, Zhihao Qiu, Dewen Jiang, Gangjun Cai, **ao Yang, Junjie Liu & Gen Li

Authors
  1. Qingzhong Xu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Zhihao Qiu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Dewen Jiang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Gangjun Cai
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. **ao Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Junjie Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Gen Li
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Qingzhong Xu.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Xu, Q., Qiu, Z., Jiang, D. et al. Surface Properties of Additively Manufactured 316L Steel Subjected to Ultrasonic Rolling. J. of Materi Eng and Perform (2024). https://doi.org/10.1007/s11665-024-09173-4

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s11665-024-09173-4

Keywords

Search

Navigation