SpringerLink
Log in

Ultrasonic Impact Treatment Effect on Lcr Wave Acoustoelastic Coefficient for Stress Evaluation of Low Carbon Steel

  • Technical Article
  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

Abstract

Surface stress is very important for the performances of metals, but there is still no one suitable method for forecasting surface stress as needed, so a combined method including ultrasonic impact treatment (UIT) and critically refracted longitudinal (Lcr) wave was proposed. Based on that reason, the influence of repetition rate of UIT on Lcr wave acoustoelastic coefficient was discussed in this study. The Lcr waves of Q235 steel under different values of stress were collected by using Lcr wave experimental system, and then the difference in time of flight between Lcr waves was calculated based on the cross correlation theory, at last the relationship between Lcr wave acoustoelastic coefficient and repetition rate of UIT was discussed. Results show that although repetition rates of UIT are different, the relationship between difference in time of flight and stress is well agreed with the Lcr wave acoustoelastic theory. As repetition rate of UIT increases, Lcr wave acoustoelastic coefficient becomes higher gradually, until repetition rate of UIT is reached 600%, Lcr wave acoustoelastic coefficient is decreased. It was analyzed that the influences of repetition rate of UIT on microstructure and deformation state of Q235 steel, which were changed from microstructural fragmentation to plastic deformation, were the main reasons for the above experimental.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12

Similar content being viewed by others

References

  1. J.X. Fang, S.Y. Dong, S.B. Li, Y.J. Wang, B.S. Xu, J. Liu, B. Liu, and Y.L. Jiang, Direct Laser Deposition as Repair Technology for a Low Transformation Temperature Alloy: Microstructure, Residual Stress, and Properties, Mater. Sci. Eng. A, 2019, 748, p 119–127.

    Article  CAS  Google Scholar 

  2. A. Arabi-Hashemia, Y. Guo, J. Michler, D. Casari, C. Leinenbach, and X. Maeder, Stress Induced Martensite Variants Revealed by In Situ High Resolution Electron Backscatter Diffraction (HR-EBSD), Mater. Des., 2018, 151(8), p 83–88.

    Article  Google Scholar 

  3. J.X. Fang, S.B. Li, S.Y. Dong, Y.J. Wang, H.S. Huang, Y.L. Jiang, and B. Liu, Effects of Phase Transition Temperature and Preheating on Residual Stress in Multi-pass & Multi-layer Laser Metal Deposition, J. Alloys Compd., 2019, 792, p 928–937.

    Article  CAS  Google Scholar 

  4. C. Liu, Y. Yan, X.H. Cheng, C.J. Wang, and Y. Zhao, Residual Stress in a Restrained Specimen Processed by Post-weld Ultrasonic Impact Treatment, Sci. Technol. Weld Join., 2019, 24(3), p 193–199.

    Article  Google Scholar 

  5. B. Liu, Y.M. Yu, R.F. Li, J.Y. Gu, and P. He, Effect of Ultrasonic Impact Treatment on Surface Stress Evaluation of Laser Cladding Coating by Using Critically Refracted Longitudinal Wave, Surf. Coat. Technol., 2021 https://doi.org/10.1016/j.surfcoat.2021.127484

    Article  PubMed  Google Scholar 

  6. B. Liu, P. Fu, R.F. Li, P. He, and S.Y. Dong, Influence of crack size on stress evaluation of ferromagnetic low alloy steel with metal magnetic memory technology, Materials, 2019, 12(24), p 4028–4039.

    Article  ADS  CAS  PubMed  PubMed Central  Google Scholar 

  7. B. Liu, X.M. Xue, R.F. Li, S.J. Chen, S.Y. Dong, and F.Y. Shu, Effect of defect depth on stress evaluation of carbon steel using the metal magnetic memory technique, Mater. Eval., 2019, 77(11), p 1347–1354.

    Google Scholar 

  8. B. Liu, Z.H. Zeng, and H.P. Wang, Study on the Early Fatigue Damage Evaluation of High Strength Steel by Using Three Components of Metal Magnetic Memory Signal, NDT E Int., 2021, 117, p 102380–102385.

    Article  CAS  Google Scholar 

  9. A. Baczmański, M. Wroński, P. Kot, S. Wroński, A. Łabaza, K. Wierzbanowski, A. Ludwik and M. Marciszko-Wiąckowska, The Role of Basal Slip in the Generation of Intergranular Stresses in Magnesium Alloy Studied Using X-ray Diffraction and Modeling, Mater. Des., 2021 https://doi.org/10.1016/j.matdes.2021.109543

    Article  Google Scholar 

  10. P. Schoderbock and H. Kostenbauer, Residual Stress Determination in Thin Films by X-ray Diffraction and the Widespread Analytical Practice Applying a Biaxial Stress Model: An Outdated Oversimplification, Appl. Surf. Sci., 2021, 541, p 148531–148538.

    Article  Google Scholar 

  11. W.R. Wang, L.H. Yuan, Y. Li, M.Y. Yang, H. Zhang, and W.F. Zhang, Test Method for Residual Stress Analysis of the Inner Surface of Small Caliber Ti-3Al-2.5V Tubing by X-ray Diffraction, Vacuum, 2020, 177, p 109371–109375.

    Article  ADS  CAS  Google Scholar 

  12. J. Yang, C.B. Wan, G.M. Fu, L.T. Mao, and F.P. Chiang, Optical Method for Identification and Quantification of Full-Field Stress Distributions and Evolution in Assembled Lining Structures Based on Additively Printed Models and Phase-Shifting Methods, Tunn. Undergr. Space Technol., 2020, 119, p 104228–104238.

    Google Scholar 

  13. Q. Hatte, M. Richard-Plouet, P.Y. Jouan, P. Casari and P.A. Dubos, Simple, and Versatile Analytical Method for Monitoring the Deposition of Thin Layers by Optical Measurement, and Calculation of Residual Stress, Thin Solid Films, 2021, 725, p 138635–138642.

    Article  ADS  CAS  Google Scholar 

  14. Y. Peng, J. Zhao, L.S. Chen, and J. Dong, Residual Stress Measurement Combining Blind-Hole Drilling and Digital Image Correlation Approach, J. Constr. Steel Res., 2021, 176, p 106346–106354.

    Article  Google Scholar 

  15. W. Wang, C.H. Xu, Y.M. Zhang, Y.F. Zhou, S.H. Meng and Y. Deng, An Improved Ultrasonic Method for Plane Stress Measurement Using Critically Refracted Longitudinal Waves, NDT E Int., 2018, 99, p 117–122.

    Article  CAS  Google Scholar 

  16. C.G. Xu, W.T. Song, X.Q. Pan, H.X. Li, and S. Liu, Nondestructive Testing Residual Stress Using Ultrasonic Critical Refracted Longitudinal Wave, Phys. Proc., 2015, 70, p 594–598.

    Article  ADS  Google Scholar 

  17. D. Husson, A Perturbation Theory for the Acoustoelastic Effect of Surface Waves, Am. Inst. Phys., 1985, 57, p 1562–1568.

    Google Scholar 

  18. J. Ditri, Determination of Nonuniform Stresses in an Isotropic Elastic Half Space from Measurements of the Dispersion of Surface Waves, J Mech. Phys. Sol., 1997, 45, p 51–66.

    Article  ADS  Google Scholar 

  19. B. Liu, J.M. Li, S.Y. Dong, and F.Y. Shu, Correction for Microstructure Effect on Residual Stress Measurement of SR-FSW Joint with Lcr Wave, Russ. J. Nnodestruct., 2020, 56(2), p 131–140.

    Article  CAS  Google Scholar 

  20. E.Y. Hu, Y.M. He, and Y.M. Chen, Experimental Study on the Surface Measurement with Rayleigh wave detection technique, Appl. Acoust., 2009, 70, p 356–360.

    Article  Google Scholar 

  21. M. Duquennoy, M. Ouaftouh, and M. Qurak, Ultrasonic Evaluation of Stress in Orthotropic Materials Using Rayleigh Waves, NDT E Int., 1999, 32, p 189–199.

    Article  Google Scholar 

  22. W. Zhi, X.J. Zhou, and Y.D. Cheng, Acoustoelastic Determination of Local Surface Stresses in Polymethymethacrylate, Appl. Acoust., 2000, 61, p 477–485.

    Article  Google Scholar 

  23. B. Liu and S.Y. Dong, Stress Evaluation of Laser Cladding Coating with Critically Refracted Longitudinal Wave Based on Cross Correlation Function, Appl. Acoust., 2016, 101, p 98–103.

    Article  Google Scholar 

  24. M. Duquennoy, M. Ouaftouh, and M. Ourak, Determination of Stresses in Aluminium Alloy Using Optical Detection of Rayleigh Waves, Ultrasonics, 1999, 37, p 365–372.

    Article  Google Scholar 

  25. B. Liu, W.B. Miao, S.Y. Dong, and P. He, Grain Size Correction of Welding Residual Stress Measurement in a Carbon Steel Plate Using the Critical Refraction of Longitudinal Waves, Res. Nondestruct. Eval., 2019, 30(2), p 112–126.

    Article  ADS  Google Scholar 

  26. B. Liu, Z.H. Zeng, J.Y. Gu, S.J. Chen, P. He, and J.X. Fang, Burial Depth Effect of Crack on the Lcr Wave Acoustoelastic Coefficient for Stress Measurement of Laser Cladding Coating, Materials, 2020, 6(13), p 2823–2833.

    Article  ADS  Google Scholar 

  27. D.S. Hugues, and J.L. Kelly, Second-Order Elastic Deformation of Solid, Phys. Rev., 1951, 92, p 1145–1149.

    Article  ADS  Google Scholar 

  28. R.B. Thompson, W.Y. Lu, and A.V. Clark, Ultrasonic Methods, Handbook of Measurement of Residual Stresses. J. Lu Ed., Society of Experimental Mechanics, Bethel (CT), 1996, p 149–178

    Google Scholar 

  29. O. **nxin, L. Laiyuan, and X. **yu, Time Delay Estimation Using Windowed Differential Magnitude of Cross Correlation and its Hilbert Transform, Proc. Eng., 2012, 29, p 2033–2038.

    Article  Google Scholar 

  30. B. Liu, W.B. Miao, S.Y. Dong and P. He, Grain Size Effect on Lcr Elastic Wave for Surface Stress Measurement of Carbon Steel, Nondestruct. Test Eval., 2018, 33(2), p 139–153.

    Article  ADS  CAS  Google Scholar 

Download references

Acknowledgments

This project was supported by the National Natural Science Foundation of China (Grant Number 52275193); the Key Project (2021-JCJQ-JJ-0184); the Key Project (2022-JCJQ-ZD-302); the Jiangsu University “Qinglan Project” (Grant Number 2019); Jiangsu Province “Liudarencaigaofeng” (Grant Number GDZB-088).

Author information

Authors and Affiliations

  1. Material Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang, 212003, China

    Shichang Jiang, Bin Liu, **yu Zhang & **gyong Li

  2. National Key Laboratory for Remanufacturing, Army Academy of Armored Forces, Bei**g, 100072, China

    Lihong Dong

  3. School of Mechanical and Electrical Engineering, Jiangxi University of Science and Technology, Ganzhou, 341000, China

    Huipeng Wang

Authors
  1. Shichang Jiang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Bin Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. **yu Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Lihong Dong
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. **gyong Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Huipeng Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to Bin Liu or **gyong Li.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Jiang, S., Liu, B., Zhang, J. et al. Ultrasonic Impact Treatment Effect on Lcr Wave Acoustoelastic Coefficient for Stress Evaluation of Low Carbon Steel. J. of Materi Eng and Perform 33, 2392–2402 (2024). https://doi.org/10.1007/s11665-023-08152-5

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11665-023-08152-5

Keywords

Search

Navigation