Abstract
In this paper, synthesis and physical properties of activated carbon modified with zeolite as hybrid nanocomposites have been studied for drinking water treatment applications. To study structural and chemical absorption characteristics, samples of activated carbon/zeolite nanocomposite with different concentrations were synthesized including the following: four sample-based activated carbon/zeolite nanocomposite with 20, 40, 60, and 80 percent zeolite and four samples-based zeolite nanocomposites with 20, 40, 60, and 80 percent activated carbon. The physical properties of the nanocomposites have been characterized by XRD, FESEM, UV-Vis spectroscopy, BET, hardness, and total dissolved solids (TDS) measurements. The study of structural properties by X-ray diffraction (XRD) showed the existence of the crystalline phase of zeolite and the porous activated carbon. Field emission scanning electron microscopy (FESEM) images clearly show the porosity and the presence of pores in composites. The optical absorption coefficient and band gap were studied by UV-Vis spectroscopy. The bandgap calculation showed that the addition of zeolite to activated carbon-based nanocomposite leads to increasing the bandgap (1.98 eV to 2.36 eV) and with addition of activated carbon in zeolite-based composites, the bandgap is decreased (2.23 eV to 2.19 eV). By effective surface area (BET) analysis, the hole diameter changes from 16 to 50 nm. For nanocomposites of activated carbon/zeolite, deletion of NaCl and ionic pollutants from Caspian seawater and non-drinkable water of Damghan desert region in Iran were tested. The measurement of point zero charge (PZC) experiments and adsorption capacity (qe) showed satisfactory results from the separation of Na+ and Cl- ions and the decrease in hardness of salty water and ion conductivity of the samples of seawater and non-drinkable water of desert up to 70%.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Data Availability
The datasets generated during and/or analyzed during the current study are available from the corresponding author on reasonable request.
References
Anis, S. F., Hashaikeh, R., & Hilal, N. (2019). Reverse osmosis pretreatment technologies and future trends: A comprehensive review. Desalination, 452(February), 159–195. https://doi.org/10.1016/j.desal.2018.11.006
Ceyhan, A. A., Şahin, Ö., Baytar, O., & Saka, C. (2013). Surface and Porous characterization of activated carbon prepared from pyrolysis of biomass by two-stage procedure at low activation temperature and it’s the adsorption of iodine. Journal of Analytical and Applied Pyrolysis, 104(November), 378–383. https://doi.org/10.1016/j.jaap.2013.06.009
Ceyhan, A. A., Şahin, Ö., Saka, C., & Yalçın, A. (2013). A novel thermal process for activated carbon production from the vetch biomass with air at low temperature by two-stage procedure. Journal of Analytical and Applied Pyrolysis, 104(November), 170–175. https://doi.org/10.1016/j.jaap.2013.08.007
Cheng, H. N., Wartelle, L. H., Thomas Klasson, K., & Edwards, J. C. (2010). Solid-state NMR and ESR studies of activated carbons produced from pecan shells. Carbon, 48(9), 2455–2469. https://doi.org/10.1016/j.carbon.2010.03.016
Chmiola, J., Yushin, G., Gogotsi, Y., Portet, C., Simon, P., & Taberna, P. L. (2006). Anomalous increase in carbon capacitance at pore sizes less than 1 nanometer. Science, 313(5794), 1760–1763. https://doi.org/10.1126/science.1132195
Cho, S., Lim, J., Cho, H., Yoo, Y., Kang, D., & Kim, J. (2022). Novel process design of desalination wastewater recovery for CO2 and SOX utilization. Chemical Engineering Journal, 433, 133602. https://doi.org/10.1016/j.cej.2021.133602
Czárán, E. (1991). Introduction to zeolite science and practice. Reaction Kinetics & Catalysis Letters, 45(1), 161–163. https://doi.org/10.1007/BF02078624
Czárán, E. (1992). Catalysis and adsorption by zeolities. Reaction Kinetics & Catalysis Letters, 46(1), 241–243. https://doi.org/10.1007/BF02096703
Darre, N. C., & Toor, G. S. (2018). Desalination of water: A review. Current Pollution Reports, 4(2), 104–111. https://doi.org/10.1007/s40726-018-0085-9
de Ridder, D. J., Verliefde, A. R. D., Schoutteten, K., van der Linden, B., Heijman, S. G. J., Beurroies, I., Denoyel, R., Amy, G. L., & van Dijk, J. C. (2013). Relation between interfacial energy and adsorption of organic micropollutants onto activated carbon. Carbon, 53(March), 153–160. https://doi.org/10.1016/j.carbon.2012.10.042
Dedet, A., Mulyono, A., Putra, R. D., & Syakti, A. D. (2023). Analysis of heavy metal contents (Cu. Pb and Zn) of coral annual band (Porites lutea) in the Eastern Part of Bintan Island. IOP Conference Series: Earth and Environmental Science, 1148(1), 012019. https://doi.org/10.1088/1755-1315/1148/1/012019
Elmouwahidi, A., Zapata-Benabithe, Z., Carrasco-Marín, F., & Moreno-Castilla, C. (2012). Activated carbons from KOH-activation of argan (Argania spinosa) seed shells as supercapacitor electrodes. Bioresource Technology, 111(May), 185–190. https://doi.org/10.1016/j.biortech.2012.02.010
Eveloy, V., Rodgers, P., & Qiu, L. (2015). Hybrid gas turbine–organic rankine cycle for seawater desalination by reverse osmosis in a hydrocarbon production facility. Energy Conversion and Management, 106(December), 1134–1148. https://doi.org/10.1016/j.enconman.2015.10.019
Fan, S., Liang, W., Wang, G., Zhang, Y., & Cao, S. (2022). A novel water-free cleaning robot for dust removal from distributed photovoltaic (PV) in water-scarce areas. Solar Energy, 241(July), 553–563. https://doi.org/10.1016/j.solener.2022.06.024
Fattahi, B., & Dekamin, M. G. (2023). Cu(II)/citric acid grafted to chitosan by dendritic units of melamine as a novel and highly efficient heterogeneous catalyst for the synthesis of 2-aminobenzothiazole derivatives. Colloid and Interface Science Communications, 54(May), 100711. https://doi.org/10.1016/j.colcom.2023.100711
Fu, J., Kang, Q., Ao, W., Wahab, N., Mao, X., Ran, C., Yang, L., Liu, G., Ellis, N., & Dai, J. (2023). Comparison and analysis of one- and two-step activation for preparation of activated carbon from furfural residues. Biomass Conversion and Biorefinery, 13(6), 4681–4694. https://doi.org/10.1007/s13399-021-01439-4
Gkika, D. A., Mitropoulos, A. C., & Kyzas, G. Z. (2022). Why reuse spent adsorbents? The latest challenges and limitations. Science of the Total Environment, 822, 153612.
González-Domínguez, J. M., Alexandre-Franco, M., Fernández-González, C., Ansón-Casaos, A., & Gómez-Serrano, V. (2017). Activated carbon from cherry stones by chemical activation: Influence of the impregnation method on porous structure. Journal of Wood Chemistry and Technology, 37(2), 148–162. https://doi.org/10.1080/02773813.2016.1253101
González-García, P., Centeno, T. A., Urones-Garrote, E., Ávila-Brande, D., & Otero-Díaz, L. C. (2013). Microstructure and surface properties of lignocellulosic-based activated carbons. Applied Surface Science, 265(January), 731–737. https://doi.org/10.1016/j.apsusc.2012.11.092
Ibrahim, A. G. M., Rashad, A. M., & Dincer, I. (2017). Exergoeconomic analysis for cost optimization of a solar distillation system. Solar Energy, 151(July), 22–32. https://doi.org/10.1016/j.solener.2017.05.020
Ioannidou, O., & Zabaniotou, A. (2007). Agricultural residues as precursors for activated carbon production—A review. Renewable and Sustainable Energy Reviews, 11(9), 1966–2005. https://doi.org/10.1016/j.rser.2006.03.013
Islam, M. A., Ahmed, M. J., Khanday, W. A., Asif, M., & Hameed, B. H. (2017). Mesoporous activated coconut shell-derived hydrochar prepared via hydrothermal carbonization-NaOH activation for methylene blue adsorption. Journal of Environmental Management, 203(December), 237–244. https://doi.org/10.1016/j.jenvman.2017.07.029
Jurado-Sánchez, B., Sattayasamitsathit, S., Gao, W., Santos, L., Fedorak, Y., Singh, V. V., Orozco, J., Galarnyk, M., & Wang, J. (2015). Self-propelled activated carbon janus micromotors for efficient water purification. Small, 11(4), 499–506. https://doi.org/10.1002/smll.201402215
Kim, M., Hong, J., Lee, J., Hong, C. K., & Shim, S. E. (2008). Fabrication of silica nanotubes using silica coated multi-walled carbon nanotubes as the template. Journal of Colloid and Interface Science, 322(1), 321–326. https://doi.org/10.1016/j.jcis.2008.03.045
Kirti, S. K., & Agarwal, V. (2023). Review on synthesis of plant-mediated green iron nanoparticles and their application for decolorization of dyes. Materials Today: Proceedings, 78, 99–107. https://doi.org/10.1016/j.matpr.2022.11.308
Li, H., Li, M., Zheng, F., Wang, J., Chen, L., Hu, P., Zhen, Q., Bashir, S., & Liu, J. L. (2021). Efficient removal of water pollutants by hierarchical porous zeolite-activated carbon prepared from coal gangue and bamboo. Journal of Cleaner Production, 325(November), 129322. https://doi.org/10.1016/j.jclepro.2021.129322
Li, H., Zheng, F., Wang, J., Zhou, J., Huang, X., Chen, L., Hu, P., et al. (2020). Facile Preparation of zeolite-activated carbon composite from coal gangue with enhanced adsorption performance. Chemical Engineering Journal, 390(June), 124513. https://doi.org/10.1016/j.cej.2020.124513
Li, Q., Wang, Y., Yu, J., Yi, B., Yang, J., & Guang-wen, X. (2013). Preparation and characterization of activated carbons from spirit lees by physical activation. Carbon, 55(April), 376. https://doi.org/10.1016/j.carbon.2012.12.054
Lim, W. C., Srinivasakannan, C., & Balasubramanian, N. (2010). Activation of palm shells by phosphoric acid impregnation for high yielding activated carbon. Journal of Analytical and Applied Pyrolysis, 88(2), 181–186. https://doi.org/10.1016/j.jaap.2010.04.004
Liu, H., Zhang, J., Zhang, C., Bao, N., & Cheng, C. (2013). Activated carbons with well-developed microporosity and high surface acidity prepared from lotus stalks by organophosphorus compounds activations. Carbon, 60(August), 289–291. https://doi.org/10.1016/j.carbon.2013.04.039
Ma, X., Li, Y., Xu, D., Tian, H., & Yang, H. (2022). Simultaneous adsorption of ammonia and phosphate using ferric sulfate modified carbon/zeolite composite from coal gasification slag. Journal of Environmental Management, 305(March), 114404. https://doi.org/10.1016/j.jenvman.2021.114404
Mahmood, T., Saddique, M. T., Naeem, A., Westerhoff, P., Mustafa, S., & Alum, A. (2011). Comparison of different methods for the point of zero charge determination of NiO. Industrial & Engineering Chemistry Research, 50(17), 10017–10023. https://doi.org/10.1021/ie200271d
Naat, J. N., Neolaka, Y. A., Lapailaka, T., Tj, R. T., Sabarudin, A., Darmokoesoemo, H., & Kusuma, H. S. (2021). Adsorption of Cu (II) and Pb (II) using silica@ mercapto (hs@ m) hybrid adsorbent synthesized from silica of Takari sand: optimization of parameters and kinetics. Rasayan Journal of Chemistry, 14(1), 550–560.
Neolaka, Y. A., Supriyanto, G., & Kusuma, H. S. (2018). Adsorption performance of Cr (VI)-imprinted poly (4-VP-co-MMA) supported on activated Indonesia (Ende-Flores) natural zeolite structure for Cr (VI) removal from aqueous solution. Journal of Environmental Chemical Engineering, 6(2), 3436–3443.
Olivares-Marín, M., Fernández-González, C., Macías-García, A., & Gómez-Serrano, V. (2007). Porous structure of activated carbon prepared from cherry stones by chemical activation with phosphoric acid. Energy & Fuels, 21(5), 2942–2949. https://doi.org/10.1021/ef060652u
Oviedo, L. R., Oviedo, V. R., Nora, L. D. D., & da Silva, W. L. (2023). Adsorption of organic dyes onto nanozeolites: A machine learning study. Separation and Purification Technology, 315(June), 123712. https://doi.org/10.1016/j.seppur.2023.123712
Puziy, A. M., Poddubnaya, O. I., Gawdzik, B., & Tascón, J. M. D. (2020). Phosphorus-containing carbons: preparation, properties and utilization. Carbon, 157(February), 796–846. https://doi.org/10.1016/j.carbon.2019.10.018
Qiu, B., Gorgojo, P., & Fan, X. (2022). Adsorption desalination: Advances in porous adsorbents. Chinese Journal of Chemical Engineering, 42(February), 151–169. https://doi.org/10.1016/j.cjche.2021.08.032
Raninga, M., Mudgal, A., Patel, V. K., Patel, J., & Sinha, M. K. (2023). Modification of activated carbon-based adsorbent for removal of industrial dyes and heavy metals: A review. Materials Today: Proceedings, 77, 286–294. https://doi.org/10.1016/j.matpr.2022.11.358
Rolf, J., Cao, T., Huang, X., Boo, C., Li, Q., & Elimelech, M. (2022). Inorganic scaling in membrane desalination: models, mechanisms, and characterization methods. Environmental Science & Technology, 56(12), 7484–7511. https://doi.org/10.1021/acs.est.2c01858
Ruiz-Fernández, M., Alexandre-Franco, M., Fernández-González, C., & Gómez-Serrano, V. (2011). Development of activated carbon from vine shoots by physical and chemical activation methods. Some insight into activation mechanisms. Adsorption, 17(3), 621–629. https://doi.org/10.1007/s10450-011-9347-1
Saka, C. (2012). BET, TG–DTG, FT-IR, SEM, Iodine number analysis and preparation of activated carbon from acorn shell by chemical activation with ZnCl2. Journal of Analytical and Applied Pyrolysis, 95(May), 21–24. https://doi.org/10.1016/j.jaap.2011.12.020
Saravanan, A., Senthil Kumar, P., Karthiga Devi, G., & Arumugam, T. (2016). Synthesis and characterization of metallic nanoparticles impregnated onto activated carbon using leaf extract of Mukia Maderasapatna: Evaluation of antimicrobial activities. Microbial Pathogenesis, 97(August), 198–203. https://doi.org/10.1016/j.micpath.2016.06.019
Sim, K. M., Kim, K. H., Hwang, G. B., Seo, S. C., Bae, G. N., & Jung, J. H. (2014). Development and evaluation of antimicrobial activated carbon fiber filters using Sophora flavescens nanoparticles. Science of The Total Environment, 493(September), 291–297. https://doi.org/10.1016/j.scitotenv.2014.06.002
Song, M., **, B., **ao, R., Yang, L., Wu, Y., Zhong, Z., & Huang, Y. (2013). The comparison of two activation techniques to prepare activated carbon from corn cob. Biomass and Bioenergy, 48(January), 250–256. https://doi.org/10.1016/j.biombioe.2012.11.007
Sych, N. V., Trofymenko, S. I., Poddubnaya, O. I., Tsyba, M. M., Sapsay, V. I., Klymchuk, D. O., & Puziy, A. M. (2012). Porous structure and surface chemistry of phosphoric acid activated carbon from corncob. Applied Surface Science, 261(November), 75–82. https://doi.org/10.1016/j.apsusc.2012.07.084
Taer, E., Deraman, M., Talib, I. A., Umar, A. A., Oyama, M., & Yunus, R. M. (2010). Physical, electrochemical and supercapacitive properties of activated carbon pellets from pre-carbonized rubber wood sawdust by CO2 activation. Current Applied Physics, 10(4), 1071–1075. https://doi.org/10.1016/j.cap.2009.12.044
Treviño-Cordero, H., Juárez-Aguilar, L. G., Mendoza-Castillo, D. I., Hernández-Montoya, V., Bonilla-Petriciolet, A., & Montes-Morán, M. A. (2013). Synthesis and adsorption properties of activated carbons from biomass of Prunus domestica and Jacaranda mimosifolia for the removal of heavy metals and dyes from water. Industrial Crops and Products, 42(March), 315–323. https://doi.org/10.1016/j.indcrop.2012.05.029
Wang, J., Zhou, Y., & **aotian, H. (2022). Adsorption of CO2 by a novel zeolite doped amine modified ternary aerogels. Environmental Research, 214(November), 113855. https://doi.org/10.1016/j.envres.2022.113855
Yang, C., Donglei, B., & Huang, S. (2022). Solvent-Free synthesis of highly porous boron carbon nitride for effective water cleaning. Ceramics International, 48(19), 27658–27663. https://doi.org/10.1016/j.ceramint.2022.06.063
Yang, K., **hui, P., Srinivasakannan, C., Zhang, L., **a, H., & Duan, X. (2010). Preparation of high surface area activated carbon from coconut shells using microwave heating. Bioresource Technology, 101(15), 6163–6169. https://doi.org/10.1016/j.biortech.2010.03.001
Zhang, S., Yu, Y., **e, M., Cheng, D., Chen, J., Wan, L., & Zhang, Y. (2022). Clean production of N, O-doped activated carbon by water vapor carbonization/activation of expired coffee for high-volumetric supercapacitor. Applied Surface Science, 589(July), 153011. https://doi.org/10.1016/j.apsusc.2022.153011
Author information
Authors and Affiliations
Contributions
All authors contributed to the study conception and design. Material preparation, data collection, and analysis were performed by A. Kazempour and M. M. Bagheri-Mohagheghi. The first draft of the manuscript was written by M. M. Bagheri-Mohagheghi, and all authors commented on previous versions of the manuscript. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethical Approval
Not applicable
Conflict of Interest
The authors declare no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Kazempour, A., Bagheri-Mohagheghi, M.M. Activated Carbon/Zeolite Hybrid Nanocomposite for Drinking Water Treatment Applications: Structural, Optical, and Surface Adsorption Properties. Water Air Soil Pollut 234, 669 (2023). https://doi.org/10.1007/s11270-023-06676-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11270-023-06676-z