Abstract
The drying properties and the performance of the chia oil (CO) as a novel healing agent for self-healing coatings are reported in this work, in comparison with linseed oil (LO). The drying properties of both oils were estimated by their respective drying rates (D.R.) between 0 and 500 h by Fourier-transform infrared spectroscopy. The D.R. of CO at 216 h was 47% higher than LO, which was attributed to its higher polyunsaturated fatty acids content. CO and LO were encapsulated in poly(urea–formaldehyde) microcapsules by in situ polymerization in oil-in-water emulsion, showing mean diameters of 20 and 23 µm, respectively. Coatings loaded with 10 wt% of microcapsules were applied onto AISI 1020 steel surfaces. The effect of these drying oils as healing agents for self-healing coatings was evaluated by artificial scratches and measured by potentiodynamic polarization test (PPT) and electrochemical impedance spectroscopy (EIS) techniques. Scratched samples showed an increasing corrosion potential of only 4 h after the scratch simulation, according to the PPT. EIS results showed that coatings containing CO as a healing agent had lower double-layer capacitance (QPE2-Q), suggesting a slight improved self-healing effect compared to LO.
Graphic abstract
Similar content being viewed by others
References
Lazzari M, Chiantore O (1999) Drying and oxidative degradation of linseed oil. Polym Degrad Stab 65(2):303–313. https://doi.org/10.1016/s0141-3910(99)00020-8
Rosu L, Varganici CD, Mustata F, Rosu D, Rosca I, Rusu T (2020) Epoxy coatings based on modified vegetable oils for wood surface protection against fungal degradation. ACS Appl Mater Interfaces 12(12):14443–14458. https://doi.org/10.1021/acsami.0c00682
Mallégol J, Lemaire J, Gardette JL (2000) Drier influence on the curing of linseed oil. Prog Org Coat 39(2–4):107–113. https://doi.org/10.1016/S0300-9440(00)00126-0
Giakoumis EG (2018) Analysis of 22 vegetable oils’ physico-chemical properties and fatty acid composition on a statistical basis, and correlation with the degree of unsaturation. Renew Energy 126:403–419. https://doi.org/10.1016/j.renene.2018.03.057
Santos JCO, Dos Santos IMG, De Souza AG, Prasad S, Dos Santos AV (2002) Thermal stability and kinetic study on thermal decomposition of commercial edible oils by thermogravimetry. J Food Sci 67(4):1393–1398. https://doi.org/10.1111/j.1365-2621.2002.tb10296.x
Arminger B, Gindl-Altmutter W, Keckes J, Hansmann C (2019) Facile preparation of superhydrophobic wood surfaces via spraying of aqueous alkyl ketene dimer dispersions. RSC Adv 9(42):24357–24367. https://doi.org/10.1039/C9RA03700D
Janesch J, Czabany I, Hansmann C, Mautner A, Rosenau T, Gindl-Altmutter W (2020) Transparent layer-by-layer coatings based on biopolymers and CeO2 to protect wood from UV light. Prog Org Coat 138:105409. https://doi.org/10.1016/j.porgcoat.2019.105409
Silva ACM, Moghadam AD, Singh P, Rohatgi PK (2017) Self-healing composite coatings based on in situ micro–nanoencapsulation process for corrosion protection. J Coat Technol Res. https://doi.org/10.1007/s11998-016-9879-0
Lima GES, Nunes EV, Dantas RC, Meneghetti MR, Meneghetti SMP (2015) Systematic investigation of the oxidative polymerization of linseed oil catalyzed by Co (II), Mn (II), and Fe (II) complexes with chelating nitrogen ligands. Eur J Lipid Sci Technol 117(2):229–234. https://doi.org/10.1002/ejlt.201400091
Soucek MD, Khattab T, Wu J (2012) Review of autoxidation and driers. Prog Org Coat 73(4):435–454. https://doi.org/10.1016/j.porgcoat.2011.08.021
Soliman H, Qian J, Tang S, Chen Y, Makhlouf AS, Wan G (2020) Hydroxyquinoline/nano-graphene oxide composite coating of self-healing functionality on treated Mg alloys AZ31. Surf Coat Technol 385:125395. https://doi.org/10.1016/j.surfcoat.2020.125395
Ataei S, Khorasani SN, Neisiany RE (2019) Biofriendly vegetable oil healing agents used for develo** self-healing coatings: a review. Prog Org Coat 129:77–95. https://doi.org/10.1016/j.porgcoat.2019.01.012
White SR, Sottos NR, Geubelle PH, Moore JS, Kessler MR, Sriram SR, Viswanathan S (2001) Autonomic healing of polymer composites. Nature 409(6822):794–797. https://doi.org/10.1038/35057232
Cairns LK, Forbes PB (2020) Insights into the yellowing of drying oils using fluorescence spectroscopy. Herit Sci 8(1):1–11. https://doi.org/10.1186/s40494-020-00403-1
Silva ACM, Renzetti RA, Andrada ADS, Singh P, Rohatgi PK, da Silva MC (2020) Adapted synthesis routes and healing evaluation of a self-healing anticorrosive coating. J Coat Technol Res 17:1351–1361
Boura SH, Peikari M, Ashrafi A, Samadzadeh M (2012) Self-healing ability and adhesion strength of capsule embedded coatings: micro and nano sized capsules containing linseed oil. Prog Org Coat 75(4):292–300. https://doi.org/10.1016/j.porgcoat.2012.08.006
Behzadnasab M, Esfandeh M, Mirabedini SM, Zohuriaan-Mehr MJ, Farnood RR (2014) Preparation and characterization of linseed oil-filled urea–formaldehyde microcapsules and their effect on mechanical properties of an epoxy-based coating. Colloids Surf, A 457:16–26. https://doi.org/10.1016/j.colsurfa.2014.05.033
Shisode PS, Patil CB, Mahulikar PP (2018) Preparation and characterization of microcapsules containing soybean oil and their application in self-healing anticorrosive coatings. Polym-Plast Technol Eng 57(13):1334–1343. https://doi.org/10.1080/03602559.2017.1381248
Ataei S, Hassan A, Azari P, **guan-Murphy B, Yahya R, Basirun WJ, Shahabudin N (2020) Electrosprayed PMMA microcapsules containing green soybean oil-based acrylated epoxy and a thiol: a novel resin for smart self-healing coatings. Smart Mater Struct. https://doi.org/10.1088/1361-665X/ab9754
Baharom Z, Idris MI, Lee TC, Abdullah HZ (2020) Comparative study on microencapsulated of natural and waste sunflower oil as self-healing agent. Mater Sci Forum 1010:439–444
Li J, Shi H, Liu F, Han EH (2021) Self-healing epoxy coating based on tung oil-containing microcapsules for corrosion protection. Prog Coat 156:106236
Feng Y, Cui Y, Zhang M, Li M, Li H (2021) Preparation of tung oil-loaded PU/PANI microcapsules and synergetic anti-corrosion properties of self-healing epoxy coatings. Macromol Mater Eng 306(2):2000581
Piva GS, Weschenfelder TA, Franceschi E, Cansian RL, Paroul N, Steffens C (2018) Extraction and modeling of flaxseed (Linnum usitatissimum) oil using subcritical propane. J Food Eng 228:50–56. https://doi.org/10.1016/j.jfoodeng.2018.02.012
Sande D, Colen G, dos Santos GF, Ferraz VP, Takahashi JA (2018) Production of omega 3, 6, and 9 fatty acids from hydrolysis of vegetable oils and animal fat with Colletotrichum gloeosporioides lipase. Food Sci Biotechnol 27(2):537–545. https://doi.org/10.1007/s10068-017-0249-1
Yan M, Frank EM, Cochran EW (2018) Effects of vegetable oil composition on epoxidation kinetics and physical properties. J Am Oil Chem Soc 95(2):209–216. https://doi.org/10.1002/aocs.12014
Grimes SJ, Phillips TD, Hahn V, Capezzone F, Graeff-Hönninger S (2018) Growth, yield performance, and quality parameters of three early flowering Chia (Salvia hispanica L.) genotypes cultivated in Southwestern Germany. Agriculture 8(10):154. https://doi.org/10.3390/agriculture8100154
De Falco B, Amato M, Lanzotti V (2017) Chia seeds products: an overview. Phytochem Rev 16(4):745–760. https://doi.org/10.1007/s11101-017-9511-7
Larios-Galvez AK, Porcayo-Calderon J, Salinas-Bravo VM, Chacon-Nava JG, Gonzalez-Rodriguez JG, Martinez-Gomez L (2017) Use of Salvia hispanica as an eco-friendly corrosion inhibitor for bronze in acid rain. Anti-Corrosion Methods Mater. https://doi.org/10.1108/ACMM-02-2017-1760
Hermoso-Diaz IA, Velázquez-González MA, Lucio-Garcia MA, Gonzalez-Rodriguez JG (2014) A study of Salvia hispanica as green corrosion inhibitor for carbon steel in sulfuric acid. Chem Sci Rev Lett 3:685–697
Dąbrowski G, Konopka I, Czaplicki S, Tańska M (2017) Composition and oxidative stability of oil from Salvia hispanica L. seeds in relation to extraction method. Eur J Lipid Sci Technol 119(5):1600209. https://doi.org/10.1002/ejlt.201600209
Timilsena YP, Vongsvivut J, Adhikari R, Adhikari B (2017) Physicochemical and thermal characteristics of Australian chia seed oil. Food Chem 228:394–402. https://doi.org/10.1016/j.foodchem.2017.02.021
González MG, Cabanelas JC, Baselga J (2012) Applications of FTIR on epoxy resins-identification, monitoring the curing process, phase separation and water uptake. Infrared Spectroscopy-Mater Sci Eng Technol 2:261–284
Mansfeld F, Lin S, Chen YC, Shih H (1988) Minimization of high-frequency phase shifts in impedance measurements. J Electrochem Soc 135(4):906
de la Paz Miguel M, Ollier R, Alvarez V, Vallo C (2016) Effect of the preparation method on the structure of linseed oil-filled poly (urea-formaldehyde) microcapsules. Prog Org Coat 97:194–202. https://doi.org/10.1016/j.porgcoat.2016.04.026
Leal DA, Riegel-Vidotti IC, Ferreira MGS, Marino CEB (2018) Smart coating based on double stimuli-responsive microcapsules containing linseed oil and benzotriazole for active corrosion protection. Corros Sci 130:56–63. https://doi.org/10.1016/j.corsci.2017.10.009
Nesterova T, Dam-Johansen K, Pedersen LT, Kiil S (2012) Microcapsule-based self-healing anticorrosive coatings: capsule size, coating formulation, and exposure testing. Prog Org Coat 75(4):309–318
Abdipour H, Rezaei M, Abbasi F (2018) Synthesis and characterization of high durable linseed oil-urea formaldehyde micro/nanocapsules and their self-healing behaviour in epoxy coating. Prog Org Coat 124:200–212. https://doi.org/10.1016/j.porgcoat.2018.08.019
Thanawala K, Mutneja N, Khanna AS, Raman RK (2014) Development of self-healing coatings based on linseed oil as autonomous repairing agent for corrosion resistance. Materials 7(11):7324–7338. https://doi.org/10.3390/ma7117324
Suryanarayana C, Rao KC, Kumar D (2008) Preparation and characterization of microcapsules containing linseed oil and its use in self-healing coatings. Prog Org Coat 63(1):72–78. https://doi.org/10.1016/j.porgcoat.2008.04.008
Wolynec, S. (2003). Técnicas eletroquímicas em corrosão Vol. 49. Edusp
Hamadou L, Kadri A, Benbrahim N (2005) Characterization of passive films formed on low carbon steel in borate buffer solution (pH 9.2) by electrochemical impedance spectroscopy. Appl Surf Sci 252(5):1510–1519. https://doi.org/10.1016/j.apsusc.2005.02.135
Acknowledgements
The authors are grateful to company POLIKINI Ind. & Comércio for providing AISI 1020 steel samples and for the support from the Materials Engineering and Mechanical Engineering laboratories at the UNIFEI-Campus Itabira. R.L.Lavall would like to thank the Brazilian Institute of Science and Technology (INCT) in Carbon Nanomaterials. A. M. P. Sakita also acknowledges the scholarships received from CAPES and CNPq. R.L. Lavall is a recipient of a fellowship from CNPq (Grant Number 315179/2020-1).
Author information
Authors and Affiliations
Corresponding authors
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
About this article
Cite this article
Silva, A.C.M., Renzetti, R.A., Sakita, A.M.P. et al. Chia oil performance as healing agent for epoxy resin-based smart coatings. Polym. Bull. 79, 8517–8533 (2022). https://doi.org/10.1007/s00289-021-03924-2
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00289-021-03924-2