Abstract
Additive manufacturing (AM) of biomedical materials provides enormous opportunities to fabricate multifunctional and structurally designed frameworks for tissue engineering, such as dental implants and bone substitutes. Despite several advantages of the binder jet 3D printing technology over other AM methods, for example, no limitations in materials selection, high materials recycling efficiency, no thermal stress development, no need to support materials, and the possibility of fabrication of printing functionally graded materials, the fabrication of biomedical-grade titanium alloys with high-density, fine microstructure, and low pickup of impurities is still challenging. This work presents the effects of powder particle size and 3D printing conditions on the microstructural features and mechanical properties of Ti-6Al-4V alloy. The formation of large and inter-aggregate pores during binder jetting is demonstrated and discussed. Design and selection of particle size distribution with a mean diameter of ~20 μm and large span and positive skewness are proposed to minimize binder-induced powder aggregation and fabricate green parts with a density of 65±1% PFD (pore-free density). Dilatometric studies under a partial pressure of argon (0.1 bar) determine that sintering just above the α/β transus temperature (~980 °C) provides a high strain rate to remove pores, but high-temperature sintering (≥1250 °C) is required to attain 97% PFD. The successful fabrication of high-density Ti-6Al-4V parts (≥96% PFD) with the microstructure comparable to metal injection molding (MIM) titanium parts (≈100 μm α grains + β lattes) is demonstrated. The tensile strength and elongation values fall in the range of 880±50 MPa and 6±2% (depending on the processing condition), which is comparable with metal injection molded parts and superior to the laser powder bed fusion technology concerning ductility. The content of carbon (<0.02 wt.%) and nitrogen (0.01 wt.%) also falls in the standard region of metal injection molding. However, oxygen pickup during sintering moderately increases the oxygen content (for 30–50%) over the standard level. The concentration of interstitials entrapped in the metal is comparable to that of parts manufactured by the powder bed fusion process, but the mechanical properties are better matched with the commercial titanium alloy. The fabrication of the titanium alloy as per the ASTM F2885 standard provides an excellent opportunity for the binder jetting process to develop custom-made biomaterials.
Similar content being viewed by others
References
Gibson I, Rosen D, Stucker B (2015) Additive manufacturing technologies: 3D printing, rapid prototy**, and direct digital manufacturing, second edition. Johnson Matthey Technol Rev 59:193–198. https://doi.org/10.1007/978-1-4939-2113-3
Parab ND, Barnes JE, Zhao C et al (2019) Real time observation of binder jetting printing process using high-speed X-ray imaging. Sci Rep 9:2499. https://doi.org/10.1038/s41598-019-38862-7
Zuo X, Zhang W, Chen Y et al (2022) Wire-based directed energy deposition of NiTiTa shape memory alloys: microstructure, phase transformation, electrochemistry, X-ray visibility and mechanical properties. Addit Manuf 59:103115. https://doi.org/10.1016/j.addma.2022.103115
Li B, Wang L, Wang B et al (2022) Electron beam freeform fabrication of NiTi shape memory alloys: crystallography, martensitic transformation, and functional response. Mater Sci Eng A 843:143135. https://doi.org/10.1016/j.msea.2022.143135
Mostafaei A, Elliott AM, Barnes JE et al (2021) Binder jet 3D printing—process parameters, materials, properties, modeling, and challenges. Prog Mater Sci 119:100707. https://doi.org/10.1016/j.pmatsci.2020.100707
Moon J, Caballero AC, Hozer L et al (2001) Fabrication of functionally graded reaction infiltrated SiC-Si composite by three-dimensional printing (3DPTM) process. Mater Sci Eng A 298:110–119. https://doi.org/10.1016/s0921-5093(00)01282-x
Barthel B, Hein SD, Aumund-Kopp C, Petzoldt F (2019) Influence of particle size distribution in metal binder jetting – Effects on the properties of green and sintered parts. In: Euro PM2019 Congress & Exhibition. Maastricht, Netherlands
Rishmawi I, Salarian M, Vlasea M (2018) Tailoring green and sintered density of pure iron parts using binder jetting additive manufacturing. Addit Manuf 24:508–520. https://doi.org/10.1016/j.addma.2018.10.015
Ziaee M, Tridas EM, Crane NB (2017) Binder-jet printing of fine stainless steel powder with varied final density. JOM 69:592–596. https://doi.org/10.1007/s11837-016-2177-6
Verlee B, Dormal T, Lecomte-Beckers J (2012) Density and porosity control of sintered 316l stainless steel parts produced by additive manufacturing. Powder Metall 55:260–267. https://doi.org/10.1179/0032589912Z.00000000082
Kumar A, Bai Y, Eklund A, Williams CB (2017) Effects of hot isostatic pressing on copper parts fabricated via binder jetting. Procedia Manufacturing, pp 935–944
Bai Y, Wagner G, Williams CB (2017) Effect of particle size distribution on powder packing and sintering in binder jetting additive manufacturing of metals. J Manuf Sci Eng Trans ASME 139:1–15. https://doi.org/10.1115/1.4036640
Nandwana P, Elliott AM, Siddel D et al (2017) Powder bed binder jet 3D printing of Inconel 718: densification, microstructural evolution and challenges☆. Curr Opin Solid State Mater Sci 21:207–218. https://doi.org/10.1016/j.cossms.2016.12.002
Mostafaei A, Behnamian Y, Krimer YL et al (2016) Effect of solutionizing and aging on the microstructure and mechanical properties of powder bed binder jet printed nickel-based superalloy 625. Mater Des 111:482–491. https://doi.org/10.1016/j.matdes.2016.08.083
Sheydaeian E, Fishman Z, Vlasea M, Toyserkani E (2017) On the effect of throughout layer thickness variation on properties of additively manufactured cellular titanium structures. Addit Manuf 18:40–47. https://doi.org/10.1016/j.addma.2017.08.017
Wiria FE, Shyan JYM, Lim PN et al (2010) Printing of titanium implant prototype. Mater Des 31:S101–S105. https://doi.org/10.1016/j.matdes.2009.12.050
Dourandish M, Simchi A, Godlinski D (2008) Rapid manufacturing of Co-Cr-Mo implants by three- dimentional printing process for orthopedic applications. Iran J Pharm Sci 4:31–36
Dourandish M, Godlinski D, Simchi A (2007) 3D printing of biocompatible PM-materials. Mater Sci Forum 534–536:453–456. https://doi.org/10.4028/www.scientific.net/msf.534-536.453
Mostafaei A, Rodriguez De Vecchis P, Buckenmeyer MJ et al (2019) Microstructural evolution and resulting properties of differently sintered and heat-treated binder-jet 3D-printed Stellite 6. Mater Sci Eng C 102:276–288. https://doi.org/10.1016/j.msec.2019.04.011
Paranthaman MP, Shafer CS, Elliott AM et al (2016) Binder jetting: a novel NdFeB bonded magnet fabrication process. JOM 68:1978–1982. https://doi.org/10.1007/s11837-016-1883-4
Caputo MP, Berkowitz AE, Armstrong A et al (2018) 4D printing of net shape parts made from Ni-Mn-Ga magnetic shape-memory alloys. Addit Manuf 21:579–588. https://doi.org/10.1016/j.addma.2018.03.028
Cramer CL, Nandwana P, Yan J et al (2019) Binder jet additive manufacturing method to fabricate near net shape crack-free highly dense Fe-6.5 wt.% Si soft magnets. Heliyon 5:e02804. https://doi.org/10.1016/j.heliyon.2019.e02804
Khorasani AM, Goldberg M, Doeven EH, Littlefair G (2015) Titanium in biomedical applications—properties and fabrication: a review. J Biomater Tissue Eng 5:593–619. https://doi.org/10.1166/jbt.2015.1361
Salvador CAF, Maia EL, Costa FH et al (2022) A compilation of experimental data on the mechanical properties and microstructural features of Ti-alloys. Sci Data 9:188. https://doi.org/10.1038/s41597-022-01283-9
Callegari B, Oliveira JP, Aristizabal K et al (2020) In-situ synchrotron radiation study of the aging response of Ti-6Al-4V alloy with different starting microstructures. Mater Charact 165:110400. https://doi.org/10.1016/j.matchar.2020.110400
Olin C (2001) Titanium in cardiac and cardiovascular applications. In: Titanium in medicine: Material Science, Surface Science, Engineering, Biological Responses and Medical Applications. Springer-Verlag, Berlin Heidelberg GmbH, Berlin, pp 889–908
Tamayo JA, Riascos M, Vargas CA, Baena LM (2021) Additive manufacturing of Ti6Al4V alloy via electron beam melting for the development of implants for the biomedical industry. Heliyon 7:e06892. https://doi.org/10.1016/j.heliyon.2021.e06892
Zhang LC, Chen LY (2019) A review on biomedical titanium alloys: recent progress and prospect. Adv Eng Mater 21:1801215. https://doi.org/10.1002/adem.201801215
Qian M, Xu W, Brandt M, Tang HP (2016) Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties. MRS Bull 41:775–783. https://doi.org/10.1557/mrs.2016.215
Nichols MR (2020) The pros & cons of powder bed fusion. Met Powder Rep 76:1–2. https://doi.org/10.1016/j.mprp.2020.04.004
Osman İ, Gepek E (2021) Characterization of CP-titanium produced via binder jetting and conventional powder metallurgy. Rev Metal 57:e205. https://doi.org/10.3989/revmetalm.205
Basalah A, Esmaeili S, Toyserkani E (2016) On the influence of sintering protocols and layer thickness on the physical and mechanical properties of additive manufactured titanium porous bio-structures. J Mater Process Technol 238:341–351. https://doi.org/10.1016/j.jmatprotec.2016.07.037
Basalah A, Shanjani Y, Esmaeili S, Toyserkani E (2012) Characterizations of additive manufactured porous titanium implants. J Biomed Mater Res - Part B Appl Biomater 100(B):1970–1979. https://doi.org/10.1002/jbm.b.32764
Wheat E, Vlasea M, Hinebaugh J, Metcalfe C (2018) Data related to the sinter structure analysis of titanium structures fabricated via binder jetting additive manufacturing. Data Br 20:1029–1038. https://doi.org/10.1016/j.dib.2018.08.135
Polozov I, Sufiiarov V, Shamshurin A (2019) Synthesis of titanium orthorhombic alloy using binder jetting additive manufacturing. Mater Lett 243:88–91. https://doi.org/10.1016/j.matlet.2019.02.027
Miyanaji H, Zhang S, Yang L (2018) A new physics-based model for equilibrium saturation determination in binder jetting additive manufacturing process. Int J Mach Tools Manuf 124:1–11. https://doi.org/10.1016/j.ijmachtools.2017.09.001
Stevens E, Schloder S, Bono E et al (2018) Density variation in binder jetting 3D-printed and sintered Ti-6Al-4V. Addit Manuf 22:746–752. https://doi.org/10.1016/j.addma.2018.06.017
Dilip JJS, Miyanaji H, Lassell A et al (2017) A novel method to fabricate TiAl intermetallic alloy 3D parts using additive manufacturing. Def Technol 13:72–76. https://doi.org/10.1016/j.dt.2016.08.001
Yadav P, Bock T, Fu Z et al (2019) Novel hybrid printing of porous TiC/Ti6Al4V composites. Adv Eng Mater 21:1900336. https://doi.org/10.1002/adem.201900336
Yadav P, Fu Z, Knorr M, Travitzky N (2020) Binder jetting 3D printing of titanium aluminides based materials: a feasibility study. Adv Eng Mater 22:2000408. https://doi.org/10.1002/adem.202000408
Sheydaeian E, Toyserkani E (2018) Additive manufacturing functionally graded titanium structures with selective closed cell layout and controlled morphology. Int J Adv Manuf Technol 96:3459–3469. https://doi.org/10.1007/s00170-018-1815-2
Merkus HG (2009) Particle size measurements: fundamentals, practice, quality. Springer Science+Business Media B.V
Chen H, Wei Q, Zhang Y et al (2019) Powder-spreading mechanisms in powder-bed-based additive manufacturing: experiments and computational modeling. Acta Mater 179:158–171. https://doi.org/10.1016/j.actamat.2019.08.030
Nor NHM, Muhamad N, Ihsan AKAM, Jamaludin KR (2013) Sintering parameter optimization of Ti-6Al-4V metal injection molding for highest strength using palm stearin binder. In: Procedia Engineering. Elsevier B V, pp 359–364
Liu S, Shin YC (2019) Additive manufacturing of Ti6Al4V alloy: a review. Mater Des 164:107552. https://doi.org/10.1016/j.matdes.2018.107552
Composition C, Properties P (2020) ATI 6-4: Ti-6Al-4V alloy. Alloy Dig 69:Ti-171. https://doi.org/10.31399/asm.ad.ti171
Nakajima H, Koiwa M (1991) Diffusion in titanium. ISIJ Int 31:757–766. https://doi.org/10.2355/isi**ternational.31.757
German RM (1996) Sintering: theory and practice, 1st edn. Wiley-Interscience
Benzing J, Hrabe N, Quinn T et al (2019) Hot isostatic pressing (HIP) to achieve isotropic microstructure and retain as-built strength in an additive manufacturing titanium alloy (Ti-6Al-4V). Mater Lett 257:126690. https://doi.org/10.1016/j.matlet.2019.126690
Bolzoni L, Ruiz-Navas EM, Zhang D, Gordo E (2012) Modification of sintered titanium alloys by hot isostatic pressing. Key Eng Mater 520:63–69. https://doi.org/10.4028/www.scientific.net/KEM.520.63
German RM (2013) Progress in titanium metal powder injection molding. Materials (Basel) 6:3641–3662. https://doi.org/10.3390/ma6083641
Murray JL, Wriedt HA (1987) The O-Ti (oxygen-titanium) system. J Phase Equilibria 8:148–165. https://doi.org/10.1007/BF02873201
Bignolas JB, Bujor M, Bardolle J (1981) A study of the early stages of the kinetics of titanium oxidation by auger electron spectroscopy and mirror electron microscopy. Surf Sci 108:L453–L459. https://doi.org/10.1016/0039-6028(81)90442-8
Nikiel P, Wróbel M, Szczepanik S et al (2021) Microstructure and mechanical properties of titanium grade 23 produced by selective laser melting. Arch Civ Mech Eng 21:152. https://doi.org/10.1007/s43452-021-00304-5
Merkushev A, Ilyinikh M, State F et al (2017) Effect of oxygen and nitrogen contents on the structure of the ti-6al-4v alloy manufactured by selective laser melting. In: Proceedings III International Scientific Conference: Material Science. Nonequilibrium Phase Transformations, pp 101–103
Ogden HR, Jaffee RI (1955) The effects of carbon, oxygen and nitrogen on the mechanical properties of titanium and titanium alloys. Titan Metall Lab 20:101
Zhang XC, Zhong F, Shao JB et al (2016) Failure mechanism and mode of Ti-6Al-4V alloy under uniaxial tensile loading: experiments and micromechanical modeling. Mater Sci Eng A 676:536–545. https://doi.org/10.1016/j.msea.2016.09.019
Moridi A, Demir AG, Caprio L et al (2019) Deformation and failure mechanisms of Ti–6Al–4V as built by selective laser melting. Mater Sci Eng A 768:138456. https://doi.org/10.1016/j.msea.2019.138456
do Prado RF, Esteves GC, ELDS S et al (2018) In vitro and in vivo biological performance of porous Ti alloys prepared by powder metallurgy. PLoS One 13:e0196169. https://doi.org/10.1371/journal.pone.0196169
Funding
AS acknowledges the Alexander von Humboldt Foundation for granting a research fellowship to carry out this study at the Fraunhofer IFAM institute. He also thanks Sharif University of Technology for providing facilities to perform complementary analyses (QA970816). The authors certify that they have no affiliations with or involvement in any organization or entity with any financial or non-financial interest in the subject matter or materials discussed in this manuscript.
Author information
Authors and Affiliations
Contributions
Abdolreza Simchi: conceptualization, methodology, investigation, formal analysis, data curing, validation, writing—original draft, and writing—review and editing. Frank Petzoldt: conceptualization, resources, project administration, and financial acquisition. Thomas Hartwig: formal analysis and data curation. Sebastian Boris Hein: visualization, data curation, and writing—review and editing. Bastian Barthel: visualization and software.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
ESM 1
(PDF 363 kb)
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Simchi, A., Petzoldt, F., Hartwig, T. et al. Microstructural development during additive manufacturing of biomedical grade Ti-6Al-4V alloy by three-dimensional binder jetting: material aspects and mechanical properties. Int J Adv Manuf Technol 127, 1541–1558 (2023). https://doi.org/10.1007/s00170-023-11661-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-023-11661-1