Abstract
Laser welding processes offer significant advantages such as high welding speed, narrow heat affected zone and quality of the welding joint. In this study, the process parameters of laser power and welding speed were modified for AISI 1018 steel plates of 8 mm thickness and compared using finite element method. The results of cross-section microstructure, heat affected zone and fusion zone were characterized. The grain refinement was affected as the parameters were modified. Tensile and microhardness tests were performed to determine the mechanical properties of the welding joints. Microhardness increased in fusion zone and decreased in heat affected zone. Tensile test showed ductile fracture in heat affected zone of the welding joints. The simulated profiles were compared with the experimental observations showing a reasonable agreement.
Similar content being viewed by others
References
M. R. D. K. S. Qian, D. Hong-Shuang, L. Jun-Chen, W. Bao-Qiang, “A comparative study of the microstructure and properties of 800MPa microalloyed C-Mn steel welded joints by laser and gas metal arc welding,” Mater. Sci. Eng. A, vol. 669, pp. 150–158, 2016.
J. A. Alcock and B. Baufeld, “Diode laser welding of stainless steel 304L,” J. Mater. Process. Technol., vol. 240, pp. 138–144, 2016.
M. N. Esfahani, J. Coupland, and S. Marimuthu, “Microstructure and mechanical properties of a laser welded low carbon-stainless steel joint,” J. Mater. Process. Technol., vol. 214, pp. 2941–2948, 2014.
R. Wang, Y. Lei, and Y. Shi, “Numerical simulation of transient temperature field during laser keyhole welding of 304 stainless steel sheet,” Opt. Laser Technol., vol. 43, pp. 870– 873, 2011.
L. J. Zhang, J. X. Zhang, A. Gumenyuk, M. Rethmeier, and S. J. Na, “Numerical simulation of full penetration laser welding of thick steel plate with high power high brightness laser,” J. Mater. Process. Technol., vol. 214, pp. 1710–1720, 2014.
C. Fang, Y. T. Song, W. Y. Wu, J. Wei, J. J. **n, H. P. Wu, and A. Salminen, “Thermal analysis of laser welding for ITER correction coil case,” Fusion Eng. Des., vol. 100, pp. 357–363, 2015.
J. Ma, F. Kong, and R. Kovacevic, “Finite-element thermal analysis of laser welding of galvanized high-strength steel in a zero-gap lap joint configuration and its experimental verification,” Mater. Des., vol. 36, pp. 348–358, 2012.
J. J. Xu, P. Gilles, Y. G. Duan, and C. Yu, “Temperature and residual stress simulations of the NeT single-bead-on-plate specimen using SYSWELD,” Int. J. Press. Vessel. Pip., vol. 99–100, pp. 51–60, 2012.
J. Rahman Chukkan, M. Vasudevan, S. Muthukumaran, R. Ravi Kumar, and N. Chandrasekhar, “Simulation of laser butt welding of AISI 316L stainless steel sheet using various heat sources and experimental validation,” J. Mater. Process. Technol., vol. 219, pp. 48–59, 2015.
P. Jiang, C. Wang, Q. Zhou, X. Shao, L. Shu, and X. Li, “Optimization of laser welding process parameters of stainless steel 316L using FEM, Kriging and NSGA-II,” Adv. Eng. Softw., vol. 99, pp. 147–160, 2016.
P. Ã. Sathiya and M. Y. A. Jaleel, “Measurement of the bead profile and microstructural characterization of a CO2 laser welded AISI 904 L super austenitic stainless steel,” Opt. Laser Technol., 2010.
J. Wang, L. Yang, M. Sun, T. Liu, and H. Li, “A study of the softening mechanisms of laser-welded DP1000 steel butt joints,” Mater. Des., vol. 97, pp. 118–125, 2016.
D. Benasciutti, A. Lanzutti, G. Rupil, and E. F. Haeberle, “Microstructural and mechanical characterisation of laser-welded lap joints with linear and circular beads in thin low carbon steel sheets,” Mater. Des., vol. 62, pp. 205–216, 2014.
H. Bhadeshia and R. Honeycombe, “Steels: Microstructure and Properties,” Third., Elsevier Ltd., 2006, pp. 10.
D. A. Porter and K. E. Easterling, “Phase Transformations in Metals and Alloys,” Second., Chapman & Hall, 1992, pp. 347.
Z. P. **ong, A. G. Kostryzhev, N. E. Stanford, and E. V. Pereloma, “Microstructures and mechanical properties of dual phase steel produced by laboratory simulated strip casting,” Mater. Des., vol. 88, pp. 537–549, 2015.
M. Hazratinezhad, N. B. Mostafa Arab, A. R. Sufizadeh, and M. J. Torkamany, “Mechanical and metallurgical properties of pulsed neodymium-doped yttrium aluminum garnet laser welding of dual phase steels,” Mater. Des., vol. 33, pp. 83–87, 2012.
Y. Z. D. C. Saha, D. Westerbaan, S. S. Nayak, E. Biro, A. P. Gerlich, “Microstructure-properties correlation in fiber laser welding of dual-phase and HSLA steels,” Mater. Sci. Eng. A, vol. 607, pp. 445–453, 2014.
N. Farabi, D. L. Chen, and Y. Zhou, “Microstructure and mechanical properties of laser welded dissimilar DP600 / DP980 dual-phase steel joints,” J. Alloys Compd., vol. 509, pp. 982–989, 2011.
M. Mazar Atabaki, J. Ma, G. Yang, and R. Kovacevic, “Hybrid laser/arc welding of advanced high strength steel in different butt joint configurations,” Mater. Des., vol. 64, pp. 573–587, 2014.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Carrizalez-Vazquez, M.A., Alvarez-Vera, M., Hernández-Rodríguez, A. et al. Effect of Laser Welding on the Mechanical Properties AISI 1018 Steel. MRS Advances 2, 4031–4039 (2017). https://doi.org/10.1557/adv.2017.599
Published:
Issue Date:
DOI: https://doi.org/10.1557/adv.2017.599