Abstract
Continuous ultrasonic atomization in a closed chamber is expected to generate a mist with an equilibrium droplet concentration and size distribution. Such a mist of microdroplets with controllable mist density has been used for Aerosol Jet® printing in the fabrication of a variety of additively manufactured microscale devices. Despite many unique capabilities demonstrated with the Aerosol Jet® printing technology, its ultrasonic atomization behavior appears to be rather sensitive to the ink properties with gaps in our understanding of the fundamental physics underlying its operation. In this work, we investigate some basic mechanisms in the Aerosol Jet® ultrasonic atomizer with a lumped-parameter kinetic coagulation model for highly concentrated mist. To mitigate the difficulty with unavailable knowledge about the complex turbulent flow inside the atomizer chamber, we present results for several orders of magnitude of the turbulent energy dissipation rates to examine a range of possibilities. The same approach is taken for analyzing the scavenging effect of the swirling bulk liquid. Our results also demonstrate the theoretical possibility for achieving a mist saturation condition where the mist output from the atomizer can become insensitive to process variables. As observed in experiments, such a saturated mist is highly desirable for Aerosol Jet® printing with maximized and well-controlled throughput in additive manufacturing.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Binder S, Glatthaar M, Raddlein E (2014) Analytical investigation of aerosol jet printing. Aerosol Sci Technol 48(9):924–929
Christenson KK, Paulsen JA, Renn MJ, McDonald K, Bourassa J (2011) Direct printing of circuit boards using Aerosol Jet®. Proc Digit Fabr. 27:433–436
Collins DJ, Manor O, Winkler A, Schmidt H, Friend JR (2012) Atomization off thin water films generated by high-frequency substrate wave vibrations. Phys Rev E 86:056312
Donnelly TD, Hogan J, Mugler A, Schubmehl M, Schommer N, Bernoff AJ, Dasnerkkar S, Ditmire T (2005) Using ultrasonic atomization to produce an aerosol of micron-scale particles. Rev Sci Instrum 76:113301
Feng JQ, Renn MJ (2019) Aerosol Jet® direct-write for microscale additive manufacturing. J Micro-Nano-Manuf 7(1):011004
Feng JQ, Loveland A, Renn MJ (2019) Aerosol Jet® direct writing polymer-thick-film resistors for printed electronics. J Surf Mount Technol 34(1):24–31
Feng JQ (2023) OpenFOAM simulations for development of a mist flow diverter in aerosol jet printing. Proceedings of The 18th OpenFOAM Workshop (OFW18, 11–14 July, Genoa, Italy) https://oxford-abstracts.s3.amazonaws.com/3d98bc36-038b-4694-9af2-644b45457294.pdf
Fogler HS, Timmerhaus KD (1966) Ultrasonic atomization studies. J Acoust Soc Am 39:515–518
Friedlander SK (1962) The similarity theory of the particle size distribution of the atmospheric aerosol. Proc. First National Symposium on Aerosols, Oct. 8–13, Prague, pp 115–130
Geng J, Park H, Sajo E (2013) Simulation of aerosol coagulation and deposition under multiple flow regimes with arbitrary computational precision. Aerosol Sci Technol 47:530–542
Germann B, Ramm A, Herault F, Hamre J, Feng J (2023) Aerosol Jet® printed interconnects for millimeter-wave components. J Surf Mount Technol 36(1):20–26
Hedges M, King B, Renn M (2007) Direct writing for advanced electronics packaging. www.onboard-technology.com/pdf_giugno2007/060706.pdf
Kahn BE (2007) The M3D aerosol jet system, an alternative to inkjet printing for printed electronics. Org Print Electr 1:14–17
Klett JD (1975) A class of solutions to the steady-state, source-enhanced, kinetic coagulation equation. J Atmos Sci 32:380–389
Kruis FE, Kusters KA (1997) The collision rate of particles in turbulent flow. Chem Eng Comm 158:201–230
Lang RJ (1962) Ultrasonic atomization of liquids. J Acoust Soc Am 34:4–8
Lozano A, Garcia JA, Alconchel J, Barreras F, Calvo E, Santolaya JL (2017) Influence of liquid properties on ultrasonic atomization. 28 Conference on Liquid Atomization and Spray Systems, 6–8 September, Valencia, Spain ( https://doi.org/10.4995/ILASS2017.2017.4588 )
Miller CJ (2009) Aerosolized medications. in small animal crtical care medicine, Ed. D. C. Silverstein and K. Hopper, Elsevier, Chapter 192:814–817
Otto E, Fissan H, Park SH, Lee KW (1999) The log-normal size distribution theory of Brownian aerosol coagulation for the entire particle size range: Part II—Analytical solution using Dahneke’s coagulation kernel. J Aerosol Sci 30(1):17–34
Park SH, Kruis FE, Lee KW, Fissan H (2002) Evolution of particle size distributions due to turbulent and Brownian coagulation. Aerosol Sci Technol 36:419–432
Paulsen JA, Renn M, Christenson K, Plourde R (2012) Printing conformal electronics on 3D structures with Aerosol Jet technology. In Proceeding of Future of Instrumentation International Workshop (FIIW)
Pruppacher HR, Klett JD (1978) Microphysics of clouds and precipitation. Reidel, Dordrecht
Renn MJ, Marquez GH, King BH, Essien M, Miller WD (2002) Flow- and laser-guided direct write of electronic and biological components. In: Pique A, Chrisey DB (eds) Direct-write technologies for rapid prototy** applications: sensors, electronics, and integrated power sources. Academic Press, San Diego, pp 475–492
Renn MJ, Schrandt M, Renn J, Feng JQ (2017) Localized laser sintering of metal nanoparticle inks printed with Aerosol Jet® technology for flexible electronics. J Microelectron Electron Packag 14:132–139
Riemer N, Wexler AS (2005) Droplets to drops by turbulent coagulation. J Atoms Sci 62:1962–1975
Saffman PG, Turner JS (1956) On the collision of drops in turbulent clouds. J Fluid Mech 1:16–30
Topp MN (1973) Ultrasonic atomization—a photographic study of the mechanism of disintegration. J Aerosol Sci 4:17–25
Wang L-P, Wexler AS, Zhou Y (2000) Statistical mechanical description and modelling of turbulent collision of inertial particles. J Fluid Mech 415:117–153
Wilkinson NJ, Smith MAA, Kay RW, Harris RA (2019) A review of aerosol jet printing—a non-tranditional hybrid process for micro-manufacturing. Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-019-03438-2
Williams MMR (1988) A unified theory of aerosol coagulation. J Phys D Appl Phys 21:875–886
Zaichik LI, Alipchenkov VM (2008) The coagulation of aerosol particles in turbulent flow. High Temp 46:666–674
Zollmer V, Muller M, Renn M, Busse M, Wirth I, Godlinski D, Kardos M (2006) Printing with aerosols: a maskless deposition technique allows high definition printing of a variety of functional materials. Euro Coating J 07–08:46–55
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors have no competing interests to declare.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Feng, J., Klett, J.D. & Renn, M.J. Mist Generation Behavior in Ultrasonic Atomizer for Aerosol Jet® Printing. Aerosol Sci Eng 8, 77–86 (2024). https://doi.org/10.1007/s41810-023-00207-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41810-023-00207-3