Abstract
Failure mode and effect analysis (FMEA) is a risk analysis tool widely used in the manufacturing industry. However, traditional FMEA has limitations such as the inability to deal with uncertain failure data including subjective evaluations of experts, the absence of weight values of risk parameters, and not considering the conditionality between failure events. In this paper, we propose a holistic FMEA to overcome these limitations. The proposed approach uses the fuzzy best–worst (FBWM) method in weighting three risk parameters of FMEA, which are severity (S), occurrence (O), and detection (D), and to find the preference values of the failure modes according to parameters S and D. On the other side, it uses the fuzzy Bayesian network (FBN) to determine occurrence probabilities of the failure modes. Experts use a procedure using linguistic variables whose corresponding values are expressed in trapezoidal fuzzy numbers, and determine the preference values of the failure modes according to parameter O in the constructed BN. Thus, the FBN including expert judgments and fuzzy set theory addresses uncertainty in failure data and includes a robust probabilistic risk analysis logic to capture the dependence between failure events. As a demonstration of the approach, a case study was conducted in an industrial kitchen equipment manufacturing facility. The results of the approach have also been compared with existed methods demonstrating its robustness.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Failure is a state or condition of not meeting a desired or intended objective. For production environments, this concept is defined as the component that causes damage to engineering equipment, manufactured products or plant infrastructure, affecting operation, production and performance as well as the company's brand and reputation [21]. Planning of failure analysis within the context of risk and reliability is a strategy that contributes to minimizing the total cost, increasing the number of production, and producing higher quality products [28]. In addition, failure analysis is very effective in determining the price policies of companies [6].
Faulty product is one of the main problems faced by companies. This problem does not only result in financial loss but also causes loss of prestige (Boral et al. 2020). To continue the activities of the companies in a healthy and to make profit in today’s overwhelming competitive environment, they must increase their production quality and decrease the number of faulty products [39].
The demand for commercial cooking equipment is increasing day by day, especially due to the developments in the hotel industry. Commercial cooking equipment has a wide range of products for the preparation of large-scale dishes. The development of new cooking techniques and the differentiation of existing cooking techniques by reinterpreting increase the importance of cooking equipment day by day. In addition, this equipment is used in the training of chefs. As the quality of these equipment has a direct impact on human health, production requires special care and precision. Due to the factors mentioned above, commercial cooking equipment demands in the global market are expected to increase day by day and reach new heights (URL-1). The global commercial kitchen equipment market size is expected to grow by 6.7% annually in 2020–2027 (URL-2). Although the production process of industrial kitchen equipment is relatively simple, inevitably, the failure analysis and control attempts to be made for this sector will contribute economically to the enterprises since high volume production is realized.
To evaluate failures and comment regarding their possible effects, some systematic techniques are required such as the Bow–tie method (BT), event-tree analysis (ETA), fault tree analysis (FTA) and failure mode and effects analysis (FMEA) [7]. FMEA is one of the methods used to specify and sort failure modes (FMs). FMEA was applied for the first time in 1960 to solve problems in the space and automobile industry [8]. Thanks to the FMEA analysis, the effects of the FMs on the system performance can be determined so that necessary measures can be taken [9, 35]. The risk priority number (RPN) is used as the prioritization index in FMEA analysis. The three factors used in the calculation of RPN as product failure severity, probability of failure occurrence and the probability of failure detection. RPN is calculated by multiplying S, O, and D parameters [47]. It is integrated with many multi-criteria decision-making (MCDM) methods, data analytics methods, and sophisticated methods. Since its traditional version has limitations such as the inability to deal with uncertain failure data including subjective expert judgments, the absence of weight values for risk parameters, and not taking into account the conditionality between failure events, it has extended by incorporating BWM, BN and fuzzy set theory [11, 64].
Fuzzy best–worst method (FBWM) has many drawbacks compared to pairwise comparison-based MCDM methods like fuzzy analytical hierarchy process (FAHP). This method determines the importance weights of the criteria by providing fewer pairwise comparisons and more consistent comparison matrices. The best criterion has the most vital role in decision making, while the worst criterion has the opposite role. Moreover, this method not only obtains the weights independently, but can also be integrated with other MCDM methods. In this study, we use this method under an FMEA study.
On the other hand, the Bayesian Networks (BNs) are visual tools based on probability theory. The use of this method in failure analysis is possible by showing the relationships of failure events and the conditional probability structure between them. It is frequently used to explain uncertainty. In this study, the fuzzy version of this method “fuzzy Bayesian Network-FBN” is used in the context of an FMEA study. The evaluator role of experts in failure analysis problems requires the use of fuzzy logic theory in the face of various uncertainties. Subjectivity and uncertainty in the judgments of the evaluators about the FMs is an important and difficult problem that also occurs in the solution of the problem addressed in this study. The fuzzy set theory presented by Zadeh [61] has been previously applied to the solution of many decision problems. This theory has been developed over time and transformed into different versions and these versions have been effectively applied to many decision problems. Triangular and trapezoidal fuzzy sets are among these extensions which are widely used by scholars.
In this paper, we propose a holistic FMEA study including FBWM and FBN. The FBWM is used in the holistic approach:
-
(1)
to determine weights for three risk parameters of FMEA (S, O and D),
-
(2)
to find the preference values of the FMs with respect to two parameters (S and D).
On the other side, FBN is used to determine the occurrence probabilities (the remaining parameter of FMEA and indicated as “O”) of FMs in BN structure. Experts use a procedure adapted from Aliabadi et al. [3] using linguistic variables whose corresponding values are expressed in trapezoidal fuzzy numbers, and determine the occurrence probability of each FM in the constructed BN. As a case study application of the approach, a risk assessment was performed in an industrial kitchen equipment manufacturing facility. The results of the approach have also been compared with an FMEA-based FBWM method without including a BN to provide its robustness.
In the lights of abovementioned short comments on the aims of the study, the contributions may be shortened as follows:
-
(1)
FBWM is utilized to eliminate a drawback of FMEA which is related to the absence of weight values of risk parameters. At the same time, evaluations of each FM are performed with respect to S and D parameters by the aid of FBWM computation logic to obtain preference values.
-
(2)
A BN is designed to demonstrate conditionality between main FMs and auxiliary FMs for the studied industrial kitchen equipment manufacturing facility.
-
(3)
Using an adapted FBN procedure of Aliabadi et al. [3], final occurrence probabilities (preference values of FMs with respect to parameter “O”) of each FM are computed.
-
(4)
Obtained preference values of FMs with respect to FMEA risk parameters from both FBWM (for parameters S and D) and FBN (for parameter O) are then merged to determine final RPN of each FM. To the best of authors’ knowledge, this is the initial attempt that merges FBN and FBW as performed in this study.
Literature review
In the literature, many scholars have dealt with FMEA extensions (with BN and BWM) and applied it to risk analysis problems. For a detailed view, Table 1 presents a comprehensive review of previous FMEA studies integrating FMEA, (F)BWM and/or (F)BN. In addition, in Table 1, novelty of each study is explained with details. BWM (either in fuzzy form) and BWM (either in fuzzy form) are used together with FMEA concept in an equal number of studies (see Table 1). Moreover, some studies [12, 14, 17, 18, 20, 24, 34, 36, 42, 43, 46, 54, 56, 57, 62] use an auxiliary concept such as fuzzy MOORA, MULTIMOORA, Z-MOORA, Markov chain, GRA, VIKOR, TOPSIS, multi-objective mathematical programming, WASPAS, COPRAS, Bow-tie analysis, FTA and case-based reasoning. Lee [27] integrated FMEA and BN in the modeling of an inkjet printer. Yang et al. [58] applied fuzzy rule-based Bayesian reasoning with FMEA in the maritime industry. Yang et al. [57] demonstrated a Bayesian-based FTA and FMEA methods in software industry failure assessment. García and Gılabert (2011) created a BN in FMEA analysis of marine diesel engine systems. Ma et al. [36] designed an FMEA and FTA integrated model for BN. Zarei et al. [62] performed a risk assessment model for natural gas stations by FMEA, Bow–Tie and BN. Yang et al. [56] used case-based reasoning and FMEA together and applied for software failure assessment. Rastayesh et al. [48] performed an FMEA–BN integrated model for risk analysis in telecommunication. Nie et al. [43] proposed a novel FMEA method with FBWM, GRA, TOPSIS, and performed an implementation in an aero-engine turbine. Huang et al. [23] present a systematic review of FMEA during the years between 1998 and 2018. They analyzed 236 papers on FMEA. Interested readers and researchers can look at this useful review paper.
Methodology
Failure mode and effect analysis (FMEA)
FMEA is an old risk assessment method implemented in different application areas from manufacturing to service. It originated in the field of aerospace as a design tool by NASA in 1960s. Since then, various improvements are provided on the base version. Various sector-based types are developed such as manufacturing, service of design FMEA [52]. It contains three factors of S, O, and D. A RPN by multiplying these parameters is obtained. Each parameter takes values between 1 and 10 (1 refers to the lowest and 10 refers to the highest) [9]. Failures result in high RPN are critical and are ranked of first priority. Failures with low RPN are vice versa [45]. At the final stage, control measure suggestion is considered. Although this traditional FMEA has a strong ability in system safety assessment, there exist lots of drawbacks that are stated in the literature [4, 21], [9, 30, 33, 44, 45]. Some of those are summarized in Table 2.
More shortcoming can be found in Liu et al. [33], which is a comprehensive review of previous FMEA literature.
Fuzzy best–worst method (FBWM)
The best–worst method (BWM) is initially proposed by Rezaei [49]. It is used to obtain the importance weights of criteria in a multi-criteria decision problem. The method is based on evaluations considering the best and the worst of criterion among others [50]. Then, the model is solved as a max–min optimization problem. It is applied to various fields from manufacturing to service [37]. After its initial development and applying to various areas, it has also been extended methodologically by fuzzy sets [41]. Guo and Zhang [22] developed triangular FBWM and applied it in the logistics industry. In the following, we provide a summarization of the steps of FBWM in Fig. 1.
In determining the fuzzy weights via the FBWM method, an optimization model is required. The best-to-others (\(\tilde{w}_{B} /\tilde{w}_{j}\)) and the worst-to-others (\(\tilde{w}_{j} /\tilde{w}_{W}\)) should have \(\tilde{w}_{B} /\tilde{w}_{j} = \tilde{a}_{Bj}\) and \(\tilde{w}_{j} /\tilde{w}_{W} = \tilde{a}_{jW}\). \(\left| {\tilde{w}_{B} /\tilde{w}_{j} - \tilde{a}_{Bj} } \right|\) and \(\left| {\tilde{w}_{j} /\tilde{w}_{W} - \tilde{a}_{jW} } \right|\) for each criterion are minimized. The demonstration of any criterion matrix in TFNs is as \(\tilde{w}_{j} = (l_{j}^{w} ,m_{j}^{w} ,u_{j}^{w} )\). The model to obtain fuzzy weights is constructed as follows:
Here, \(\tilde{w}_{B} = (l_{B}^{w} ,m_{B}^{w} ,u_{B}^{w} )\),\(\tilde{w}_{j} = (l_{j}^{w} ,m_{j}^{w} ,u_{j}^{w} )\),\(\tilde{w}_{W} = (l_{W}^{w} ,m_{W}^{w} ,u_{W}^{w} )\),\(\tilde{a}_{Bj} = (l_{Bj} ,m_{Bj} ,u_{Bj} )\)\(\tilde{a}_{jW} = (l_{jW} ,m_{jW} ,u_{jW} )\). The current version of the model is a constrained optimization problem. To satisfy the conditions given below the objective function statement in Eq. (1), a solution where the maximum absolute differences of \(\left| {\tilde{w}_{B} /\tilde{w}_{j} - \tilde{a}_{Bj} } \right|\) and \(\left| {\tilde{w}_{j} /\tilde{w}_{W} - \tilde{a}_{jW} } \right|\) for all j should be minimized. This state of the problem is a min–max problem. Then, Eq. (1) is remodeled as a nonlinearly constrained optimization problem as follows:
where \(\xi = (l^{\xi } ,m^{\xi } ,u^{\xi } )\), considering \(l^{\xi } \le m^{\xi } \le u^{\xi }\). \(\zeta^{*} = (k^{*} ,k^{*} ,k^{*} )\),\(k^{*} \le l^{\zeta }\), Eq. (2) is transformed as:
Equation (3) is solved for calculating the optimal fuzzy weights \((\tilde{w}_{1}^{*} ,\tilde{w}_{2}^{*} ,...,\tilde{w}_{n}^{*} )\). A consistency check is applied as in Guo and Zhang [22] after obtaining the optimal fuzzy weights.
Fuzzy Bayesian network (FBN)
The Bayesian network (BN) method is a visual tool that is based on probability theory. In this method, a directed acyclic graph is used for demonstrating the quantity of variables and their dependency relationships [16, 51]. This method is frequently used to explain uncertainty [5]. Its notions consist of nodes and arrows. While nodes show a random variable, arrows refer to the relationship between the variables [21, 59, 60]. In a BN, the nodes with arrows pointing towards them are called child nodes and the nodes with arrows pointing outwards from themselves are called parent nodes [32]. A node with child nodes but no parent nodes is called a root node. Figure 2 demonstrates the basic idea under BN concept.
In the example given by Fig. 2, both X1 and X2 are root nodes and they are the parent nodes of X3. X3 is a child of X1 and X2. Each node has two states: ‘state 0′ and ‘state 1′. A root node has only a marginal probability. Each child has a conditional probability table associated with it showing the states of its parent nodes (Liu et al. [34]) (Table 3).
In a usual BN demonstration, some formulas are used as in the following [60]. The formula in the following equation shows the joint probability value:
Here, \({\pi }_{i}\) is the set of parents of node \({X}_{i}\). The marginal probability of \({X}_{i}\) is
As an inferential tool, BN calculates the probability of an event given other evidences. The following formulae shows the calculation procedure for the posterior probability of evidence \(e\):
Here,
\(P\left(U\right)\): the prior probability of event \(U\),
\(P\left(e\right)\): the pre-defined posterior probability of the evidence,
\(P\left(\left.U\right|e\right)\): the posterior probability of evidence \(e\),
\(P\left(\left.e\right|U\right)\): the evidence likelihood of event \(U\), and.
\(\sum_{U}P\left(\left.e\right|\mathrm{U}\right)P(\mathrm{U})\): the joint probability distribution of \(e\).
Besides the traditional form of BN modeling, there is also a fuzzy form of BN which is called fuzzy Bayesian Network (FBN). It presents uncertain information and decreases information loss [63]. In the scope of the current study, experts evaluate main FMs and auxiliary FMs with the aid of a fuzzy linguistic scale. Following a procedure which suggested by Aliabadi et al. [3], final occurrence probabilities of each FMs are obtained. Hereafter this step, BN modeling is generated and crisp failure probabilities are gained.
The holistic approach
The holistic approach which is the basis for the methodology of this study consists of four main stages. The initial stage is about preparation for failure analysis and control. In this stage, experts were determined from the enterprise. In addition, the main and auxiliary FMs were identified that cause faulty products in the enterprise. The second stage concerns with assigning importance weights to the FMEA parameters via FBWM. In this stage, preference values of each main FM are computed with respect to two of the FMEA parameters which are S and D. The values regarding the remained risk parameter “O” are calculated via a different way as presented in the third stage in details. This way concerns a probabilistic approach including BN and fuzzy logic. When viewed from the probability perspective, each preference value of the failure event that may occur randomly can be evaluated as the probability of these events occurring. For this reason, FMs can be considered as random events and their preference values as probability functions [38]. In the third stage, first, each expert was evaluated considering their characteristics, and a weighting coefficient for each expert was calculated. Then, the BN was created considering the top event, main FMs, and auxiliary FMs which affects them. The linguistic assessments of experts in fuzzy environment that are used in BN modeling were collected and converted into actual failure occurrence probabilities according to the procedure of Aliabadi et al. [3]. The flowchart of this holistic approach is provided in Fig. 3. The detailed analysis of our case will be demonstrated in the following section.
Case study
Description of the production process
The production process regarding industrial kitchen equipment includes nine different steps as given in Fig. 4. The first step is measuring. In this section, the sheets to be cut are marked according to the order on the roll. The plates are then sent to the cutting section. The stainless-steel roll is placed on the unrolling machine. In this section, first, the rectangular and then the circular-shaped plates are obtained by laser cutting. Cut plates are brought to the hydraulic press section. The sheet metal is placed in the hydraulic press. The pressure is adjusted in the press. Oil is used in order not to tear the metal in the press and to distribute the heat and pressure homogeneously. The sheets shaped in the press are brought to the washing section to remove dirt and oil residue. The plates are taken into the washing tank containing solvents to prevent any oil residue on the metal. The products are dried after washing. The outer surface becomes matte due to the processes performed. To remove this matting, the polishing process is applied to the outer surface. The hydraulic press is used again to connect the bottom of the operating pot with the side surfaces. Until these stages have been finalized, other parts of the pot, except for the handle part, have been completed. The handles of the pot are prepared and made ready for resistance welding. In the resistance welding section, the welding surfaces are cleaned by the operator. The current and welding time is adjusted by the operator. The welding surfaces are melted, and adhered to each other. It is packaged to protect ready products from external influences.
Identification of failure modes and their effects
As a result of the evaluations made in the enterprise, five main FMs were identified. These FMs are stain on the product (FM1), polishing color difference on product (FM2), scratch on the product (FM3), cracking on the product (FM4), and failure in welding of pot handles properly (FM5). In addition, eight auxiliary FMs have been determined. These are as follows: Mismeasurement (X1), Wrong cutting (X2), Unsuitable mold (X3), Usage of unsuitable oil (X4), Overloading the hydraulic press (X5), Not choosing the proper brush (X6), Improper polishing (X7) and Unsuitable raw material (X8). Failures in industrial kitchen production cause the product to be scrapped or to be sold as a low-quality product, selling them below the sales price.
Stain on the product (FM1), usually takes place in the press section. If suitable oil is not selected during pressing, the material temperature cannot be lowered by distributing the heat throughout the plastic shape change of the material. In this case, it causes a permanent stain on the product. In addition, the resistance of the raw material to the deformation of plastic, in other words, its hardness, causes stains on the product. In addition, oil-raw material compatibility must be checked before production in large batches. Polishing color difference on the product (FM2) is directly related to the raw material and polishing application. In this section, the outer surface of the product is abraded with abrasive solutions, the product contact time with the solution should be adjusted very well. The fact that the materials sent by the suppliers do not always have the same characteristics, this requires a re-evaluation of the material-solution contact time. All products produced must be of the same color. When the consumer sees products of different colors, she/he thinks this is a manufacturing failure. Polishing failure does not cause any negative function of the product. However, this situation reduces the sales price of the product. Products with polishing failures are transferred to different sales channels. Scratch on the product (FM3), is closely related to brush selection. Scratches on the product may occur if a hard brush is selected. If a soft brush is chosen, the product will not be polished to the desired level. Cracking on the product (FM4) is closely related to overloading on the hydraulic press and wrong plate cutting. Wrong cut is due to wrong measurement and inappropriate mold usage. Overloading and wrong oil selection in the hydraulic press also causes the product to crack. Unlike the others, this failure makes the product completely unusable. If the product is cracked, the product is scrapped. Failure to weld pot handles properly (FM5), the reliability of this weld depends on the cleanliness of the weld surfaces, the electrode tips not oxidized and the correct electrode selection, and the good adjustment of the welding current and time.
Implementation of FBWM
The FBWM implementation stage (second stage) concerns with assigning importance weights to the FMEA parameters. In this stage, the preference values of each main FM are also computed with respect to two of the FMEA parameters which are severity (S) and detection (D).
Determination of importance weights of FMEA parameters
In the second stage of the holistic approach, evaluations were made by six experts to determine importance weights for S, O and D parameters. FBWM was used to make calculations. As an example, the evaluation of an expert is presented in Fig. 5.
The optimal fuzzy weights of three FMEA parameters assessed by one expert are calculated as follows: \(w_{S}^{*} = (0.391, \, 0.463, \, 0.520)\),\(w_{O}^{*} = (0.300, \, 0.374, \, 0.435)\),\(w_{D}^{*} = (0.160, \, 0.168, \, 0.173)\). Then, the crisp weights are determined as follows: \(w_{S}^{{}} = (0.460)\),\(w_{O}^{{}} = (0.372)\),\(w_{D}^{{}} = (0.167)\). Similarly, the evaluations made by other experts were calculated and presented in Table 4. By averaging these values, the weight values for each parameter are computed as in Fig. 6.
Determination of priority values of FMs in terms of severity and detection parameters
Similarly, all FMs were evaluated with respect to S and D parameters. As an example, the evaluation of Expert 1 with respect to S parameter is presented in Fig. 7. Other evaluations cannot be included in the paper due to space limitations. The preference values of each main FM are computed with respect to two of the FMEA parameters which are S and D. The obtained results are presented in Table 5. By averaging the values in Table 5, the preference values of five FMs according to S and D parameters are presented in Fig. 8.
Implementation of FBN
The values regarding the remained risk parameter “occurrence (O)” are calculated via a different way as presented by Aliabadi et al. [3]. This procedure and its computational steps are given in this stage. The BN structure of main failures and auxiliary failures is presented in Fig. 9. As seen from the Fig. 9, the top event concerns with scrap** the product or designating it as a low-quality product. This will probably cause a selling below the sales price. There are seven root nodes (basic events) in the BN. These are X1, X3, X4, X6, X7, X8 and FM5. The remaining are child nodes and they have their own conditional probability table associated with its parent nodes.
We used GeNle commercial software (version 3.0) which was developed by Decision Systems Laboratory, University of Pittsburgh. Failure probability of basic events can be calculated by expert evaluation. In our case, the evaluations of six experts are considered. These experts are working as engineer, operator and technician. Their years of experience are varied between 4 and 15 years. While Expert 2 and Expert 5 have bachelor degree, Expert 1 has a Ph.D. degree on engineering. The weight factor is the sum of the coefficient of job title, years of experience, and educational level. The weighting coefficient is calculated by giving a grade to each feature (job title, year of experience, education level) between 1 to 5. For example, the weight factor of Expert 1 is 13 and the total weight factor is 45. Then, by dividing these two values, a weighting coefficient of Expert 1 is calculated as \((13/45=0.29)\). The weighting coefficients of all experts are presented in the last column of Table 6.
To obtain crisp failure occurrence probabilities using FBN, a procedure suggested by Aliabadi et al. [3] is followed. This procedure can easily aggregate the linguistic evaluations of experts and reach a consensus in finding crisp failure probabilities of main FMs. The steps in this procedure are given in Fig. 10. In the first step of this procedure, the degree of agreement between two experts among a group of experts is computed using the corresponding formulae. In the formulae, \({A}_{i}\) and \({A}_{j}\) refer to two different linguistic variables that are presented in trapezoidal fuzzy numbers style. \({A}_{i}=({a}_{1},{a}_{2},{a}_{3},{a}_{4})\) and \({A}_{j}=({b}_{1},{b}_{2},{b}_{3},{b}_{4})\). In the second and third steps, the average agreement degrees (AA values) and relative agreement degrees (RA values) are computed, respectively. In the fourth step, consensus coefficient degrees (C values) of experts are calculated using the related formulae. Here, \(\beta \) is a factor which shows the importance of weight coefficients of experts over \(RA\left({Expert}_{i}\right)\). Its values vary between 0 and 1. In the fifth step, the aggregated results of the experts are obtained. Here, \({R}_{i}\) refers to the fuzzy probability assigned by an expert. In the sixth step, the fuzzy probability of the basic and conditional events is crispified. Finally, the crisp failure occurrence probability (CFP) values are transformed into actual failure occurrence probability (FP) values using the formulae in Fig. 10. At the end of the implementation of this procedure, all calculations related to the occurrence probability values have been made. Due to space limitations in this study, we have attached them as a Supplementary file. These values cover evaluations of just one parameter of FMEA (“occurrence” parameter). Expert assessments on the other two parameters (severity and detection) of FMEA have been made via FBWM method in “Determination of priority values of FMs in terms of severity and detection parameters”. In addition, parameter weights of FMEA are assessed by experts and a weight matrix for them has been gained in “Determination of importance weights of FMEA parameters”. Then, merging of both matrices, final RPN values of each failure mode can be computed. This will be explained in the next section (“Determination of FM scores”).
In this procedure, the linguistic variables which the experts used for evaluation of basic events and their corresponding trapezoidal fuzzy numbers are presented in Table 7.
The evaluation of experts for each basic event in the constructed BN (shown in Fig. 9) is presented in Table 8. These evaluations are considered as input in the aggregation procedure. Then, the aggregation operator is applied for each basic event. We presented the details of aggregation for basic events X1 in Table 9.
In addition, the conditional probabilities of the nodes are also calculated. For example, if the basic events of X1 and X3 have occurred, the occurrence probability of conditional event X2 is calculated as 0.902. In the same manner, all possible situations are presented in Table 10.
The occurrence probabilities of FMs are then calculated, and they are given in Table 11. FM3 is determined as FM with the highest occurrence probability. Then, occurrence probabilities obtained using FBN were normalized to become suitable for matrix multiplication and comparative study.
Determination of FM scores
Two matrices are used in the RPN calculation of five FMs. The first matrix consists of three columns. The first and third columns consist of averaged preference values of FMs according to S and D parameters as presented in Fig. 7. The second column contains the normalized occurrence probabilities as given in Table 10. The second matrix includes the importance weights of FMEA parameters obtained from FBWM implementation as given in Fig. 5. By multiplying these two matrices, RPNs are obtained as follows:
Scratch on the product (FM3) has been calculated with the highest risk value of 0.276. The occurrence of this risk does not make the product scrapped, but service sectors such as hotels and restaurants avoid buying such faulty products. Therefore, the price of products with this defect drops dramatically. Cracking on the product (FM4) has been calculated as the second-highest risk value 0.204. In this case, the product is no longer usable in any way and is sent for scrap. The third highest risk has been calculated 0.183 stain on the product (FM1). Although FM1 causes a decrease in the price of the product due to cosmetic reasons similar to FM3, its effect is more limited than FM3. The fourth highest risk has been calculated 0.204 polishing color difference on the product (FM4). This risk is similar to FM1 and FM3. However, its effect is much more limited than others. This color difference can only be evaluated by experts. Generally, this situation is noticed during and after product delivery, negatively affects the brand image in the long term. The lowest risk was calculated as Failure to weld pot handles properly (FM5) with 0.157. The occurrence of this risk makes the product unusable and unsold, but it is easy to detect. In addition, technological developments in resistance welding, especially in recent years, have considerably reduced the possibility of faulty welding.
Comparative study
In our proposed approach, preference values of FMs with respect to parameters S and D were obtained via FBWM. Then, the preference values of FMs with respect to parameter O were obtained via FBN-based procedure. To test the validity of the proposed holistic approach, a benchmarking approach which considers evaluations of FMs with respect to all of the three parameters via FBWM is demonstrated. Table 12 shows the preference values of five FMs according to parameter O assessed by each expert. Preference values of FMs with respect to parameters S and D are given in Table 5.
By combining Tables 12 and (the averaged values), the first matrix is gained as in the following. Then, new RPNs were obtained by multiplying these two matrices. In the obtained results, it starts with RPN for FM1 in the first row of the matrix (a value of 0.202) and ends with RPN value for FM5 in the 5th row (a value of 0.185):
As a result of the calculation, FM ranks are as follows: \(\mathrm{RPN}3>\mathrm{ PRN}1>\mathrm{RPN}2>\mathrm{ PRN}4>\mathrm{ RPN}5.\) When the values of this RPN calculation procedure and the proposed holistic approach are compared, it is observed that the ranks are similar. The comparison results are provided in Table 13. Pearson correlation coefficient regarding ranks in both approaches was determined as 0.998. In this case, it can be said that there is a very strong relationship between the two rankings.
Conclusion
Industrial kitchen equipment is used in many commercial and non-commercial organizations such as hotels, airports, universities, shop** malls, and laboratories. The service industry plays the most important role in the rise of industrial kitchen equipment. In parallel with the development of the service industry, industrial kitchen equipment production is also develo**. Companies need to increase their quality and reduce their sales prices in order to compete in the market. For this reason, the failure analysis can be a guide in reducing the number of scrap products and increasing product quality. FMEA is one of the most frequently used failure analysis tools in the decision-making process of different industry types and operations, and it enables decision-makers to make critical decisions easier.
In this study, a failure analysis is performed for the industrial kitchen equipment production. Failures in the manufacturing process have not been easily predictable, and the complexity required a change in the traditional FMEA concept. While this traditional RPN logic may seem like a methodical way to rank failures in system safety assessment, it has many disadvantages handled in the literature up to now. Therefore, in this study, an FMEA with a holistic FBN and FBWM approach is proposed. FBWM has been injected into the proposed holistic approach to assign importance weights to the three risk parameters of FMEA and to obtain preference values of FMs with respect to S and D parameters. In addition, the FBN is used to find the actual occurrence probability values of FMs. Finally, obtained preference values of FMs with respect to all three risk parameters from both FBWM and FBN are then merged to determine final RPN of each FM.
This study has revealed a general risk analysis of the production process for the observed production facility considering all product types. In this industry, dozens of product types are produced and the production process of each product changes slightly. For future studies, a separate BN can be created for each product type. This constructed BN should include main and auxiliary FMs of each product type. Thus, it will be possible to generate a more representative FMEA for the facility, as each product type is produced in different quantities.
Another limitation of the study is that the company have not analyzed the causes of failures in the previous period and not kept the records systematically. The availability of past records would allow a more efficient computation with precise data on the FMEA parameters. Another suggestion for future studies is that the weights of the risk parameters as well as each FM can be calculated with other MCDM methods. Thus, the results obtained not only with FBWM but also from other methods will guide decision-makers.
References
(URL-1) https://www.transparencymarketresearch.com/commercial-cooking-equipment-market.html Commercial Cooking Equipment Market- Global Industry Analysis, Size, Share, Growth, Trends and Forecast 2018–2026.
(URL-2) https://www.grandviewresearch.com/industry-analysis/commercial-kitchen-equipment-appliances-market
Aliabadi MM, Pourhasan A, Mohammadfam I (2020) Risk modelling of a hydrogen gasholder using Fuzzy Bayesian Network (FBN). Int J Hydrogen Energy 45(1):1177–1186
Başhan, V., Demirel, H., & Gul, M. (2020). An FMEA-based TOPSIS approach under single valued neutrosophic sets for maritime risk evaluation: the case of ship navigation safety. Soft Computing, 1–16.
Ben‐Gal I. (2008). Bayesian networks. Encyclopedia of statistics in quality and reliability, 1.
Boodhun N, Jayabalan M (2018) Risk prediction in life insurance industry using supervised learning algorithms. Complex Intell Syst 4(2):145–154
Boral S, Howard I, Chaturvedi SK, McKee K, Naikan VNA (2020) An integrated approach for fuzzy failure modes and effects analysis using fuzzy AHP and fuzzy MAIRCA. Eng Fail Anal 108:104195
Bowles JB, Peláez CE (1995) Fuzzy logic prioritization of failures in a system failure mode, effects and criticality analysis. Reliabil Eng Syst Saf 50(2):203–213
Bozdag E, Asan U, Soyer A, Serdarasan S (2015) Risk prioritization in failure mode and effects analysis using interval type-2 fuzzy sets. Expert Syst Appl 42(8):4000–4015
Calori IC, & Stalhane T (2007) FMEA and BBN for robustness analysis in web-based applications. In European Safety and Reliability Conference.
Chang KH, Chang YC, Tsai IT (2013) Enhancing FMEA assessment by integrating grey relational analysis and the decision making trial and evaluation laboratory approach. Eng Fail Anal 31:211–224
Chang TW, Lo HW, Chen KY, Liou JJ (2019) A novel FMEA model based on rough BWM and rough TOPSIS-AL for risk assessment. Mathematics 7(10):874
Chen C, Zhang L, Tiong RLK (2020) A novel learning cloud Bayesian network for risk measurement. Appl Soft Comput 87:105947
Cheng PF, Li DP, He JQ, Zhou XH, Wang JQ, Zhang HY (2020) Evaluating surgical risk using FMEA and MULTIMOORA methods under a single-valued trapezoidal neutrosophic environment. Risk Manage Healthcare Policy 13:865
Commercial Kitchen Appliances Market Size, Share & Trends Analysis Report By Product (Refrigerator, Cooking Appliance, Dishwasher, Other Specialized Appliance), By End Use, By Region, And Segment Forecasts, 2020–2027.
Corriveau G, Guilbault R, Tahan A, Sabourin R (2016) Bayesian network as an adaptive parameter setting approach for genetic algorithms. Complex Intell Syst 2(1):1–22
Dezan C, Zermani S, Hireche C (2020) Embedded Bayesian network contribution for a safe missing planning of autonomous vehicles. Algorithms 13(7):155
Dorosti S, Fathi M, Ghoushchi SJ, Khakifirooz M, Khazaeili M (2020) Patient waiting time management through fuzzy based failure mode and effect analysis. J Intell Fuzzy Syst (Preprint) pp 1–12
García A, Gilabert EDUARDO (2011) Map** FMEA into Bayesian networks. Int J Perform Eng 7(6):525–537
Ghoushchi SJ, Yousefi S, Khazaeili M (2019) An extended FMEA approach based on the Z-MOORA and fuzzy BWM for prioritization of failures. Appl Soft Comput 81:105505
Gul M, Yucesan M, Celik E (2020) A manufacturing failure mode and effect analysis based on fuzzy and probabilistic risk analysis. Appl Soft Comput 96:106689
Guo S, Zhao H (2017) Fuzzy best-worst multi-criteria decision-making method and its applications. Knowl-Based Syst 121:23–31
Huang J, You JX, Liu HC, Song MS (2020) Failure mode and effect analysis improvement: s systematic literature review and future research agenda. Reliabil Eng Syst Saf. https://doi.org/10.1016/j.ress.2020.106885
Khalilzadeh M, Balafshan R, Hafezalkotob A (2020) Multi-objective mathematical model based on fuzzy hybrid multi-criteria decision-making and FMEA approach for the risks of oil and gas projects. J Eng Des Technol. https://doi.org/10.1108/JEDT-01-2020-0020
Kirchhof M, Haas K, Kornas T, Thiede S, Hirz M, Hermann C (2020) Root Cause Analysis in Lithium-Ion Battery Production with FMEA-Based Large-Scale Bayesian Network. ar**v Preprint. https://doi.org/10.20944/preprints202012.0312.v1
Kolagar M, Hosseini SMH, Felegari R (2020) Develo** a new BWM-based GMAFMA approach for evaluation of potential risks and failure modes in production processes. Int J Qual Reliabil Manage. https://doi.org/10.1108/IJQRM-09-2018-0230
Lee, B. H. (2001). Using Bayes belief networks in industrial FMEA modeling and analysis. In Annual Reliability and Maintainability Symposium. 2001 Proceedings. International Symposium on Product Quality and Integrity (Cat. No. 01CH37179) (pp. 7–15). IEEE.
Lee D, Choi D (2020) Analysis of the reliability of a starter-generator using a dynamic Bayesian network. Reliabil Eng Syst Saf 195:106628
Lian P, Ning N, Ai** C, Yaobin T (2010). Fault diagnosis of the blast furnace based on the Bayesian network model. In 2010 International Conference on Electrical and Control Engineering (pp. 990–993). IEEE.
Liu, H. C. (2016). FMEA using uncertainty theories and MCDM methods. In FMEA using uncertainty theories and MCDM methods (pp. 13–27). Springer, Singapore.
Liu HC, Hu YP, Wang JJ, Sun M (2018) Failure mode and effects analysis using two-dimensional uncertain linguistic variables and alternative queuing method. IEEE Trans Reliab 68(2):554–565
Liu Z, Liu Y (2019) A Bayesian network based method for reliability analysis of subsea blowout preventer control system. J Loss Prev Process Ind 59:44–53
Liu HC, Liu L, Liu N (2013) Risk evaluation approaches in failure mode and effects analysis: a literature review. Expert Syst Appl 40(2):828–838
Lo HW, Liou JJ (2018) A novel multiple-criteria decision-making-based FMEA model for risk assessment. Applied Soft Computing 73:684–696
Lo HW, Shiue W, Liou JJ, Tzeng GH (2020) A hybrid MCDM-based FMEA model for identification of critical failure modes in manufacturing. Soft Comput 24:15733–15745
Ma D, Zhou Z, Jiang Y, Ding W (2014) Constructing bayesian network by integrating fmea with fta. In 2014 Fourth International Conference on Instrumentation and Measurement, Computer, Communication and Control (pp. 696–700). IEEE.
Mi X, Tang M, Liao H, Shen W, Lev B (2019) The state-of-the-art survey on integrations and applications of the best worst method in decision making: Why, what, what for and what’s next? Omega 87:205–225
Mohammadi M, Rezaei J (2020) Bayesian best-worst method: A probabilistic group decision making model. Omega 96:102075
Moktadir MA, Ali SM, Kusi-Sarpong S, Shaikh MAA (2018) Assessing challenges for implementing Industry 4.0: Implications for process safety and environmental protection. Process Saf Environ Prot 117:730–741
Momen S, Tavakkoli-Moghaddam R, Ghasemkhani A, Shahnejat-Bushehri S, Tavakkoli-Moghaddam H (2019) Prioritizing Surgical Cancellation Factors Based on a Fuzzy Best-Worst Method: A Case Study. IFAC-PapersOnLine 52(13):112–117
Moslem S, Gul M, Farooq D, Celik E, Ghorbanzadeh O, Blaschke T (2020) An integrated approach of best-worst method (BWM) and triangular fuzzy sets for evaluating driver behavior factors related to road safety. Mathematics 8(3):414
Nie RX, Tian ZP, Wang XK, Wang JQ, Wang TL (2018) Risk evaluation by FMEA of supercritical water gasification system using multi-granular linguistic distribution assessment. Knowl-Based Syst 162:185–201
Nie W, Liu W, Wu Z, Chen B, Wu L (2019) Failure mode and effects analysis by integrating Bayesian fuzzy assessment number and extended gray relational analysis-technique for order preference by similarity to ideal solution method. Quality and Reliability Engineering International 35(6):1676–1697
Ozdemir Y, Gul M, Celik E (2017) Assessment of occupational hazards and associated risks in fuzzy environment: a case study of a university chemical laboratory. Human and Ecol Risk Assess 23(4):895–924
Park J, Park C, Ahn S (2018) Assessment of structural risks using the fuzzy weighted Euclidean FMEA and block diagram analysis. Int J Adv Manufact Technol 99(9–12):2071–2080
Peko M, Komatina N, Banduka N, Crnjac M (2018) The assessment and ranking of failures in the information technology industry based on FMEA and MCDM. Ekonomski horizonti 20(3):257–268
Qin J, ** Y, Pedrycz W (2020) Failure mode and effects analysis (FMEA) for risk assessment based on interval type-2 fuzzy evidential reasoning method. Appl Soft Comput 89:106134
Rastayesh S, Bahrebar S, Blaabjerg F, Zhou D, Wang H, Sørensen JD (2019) A system engineering approach using FMEA and Bayesian network for risk analysis—a case study. Sustainability 12(1):1–18
Rezaei J (2015) Best-worst multi-criteria decision-making method. Omega 53:49–57
Rezaei J (2016) Best-worst multi-criteria decision-making method: Some properties and a linear model. Omega 64:126–130
Song G, Khan F, Yang M (2019) Integrated risk management of hazardous processing facilities. Process Saf Prog 38(1):42–51
Stamatis, D. H. (2003). Failure mode and effect analysis: FMEA from theory to execution. Quality Press.
Taleb-Berrouane M, Khan F, Amyotte P (2020) Bayesian Stochastic Petri Nets (BSPN)-A new modelling tool for dynamic safety and reliability analysis. Reliabil Eng Syst Saf 193:106587
Tian ZP, Wang JQ, Zhang HY (2018) An integrated approach for failure mode and effects analysis based on fuzzy best-worst, relative entropy, and VIKOR methods. Appl Soft Comput 72:636–646
Wan C, Yan X, Zhang D, Qu Z, Yang Z (2019) An advanced fuzzy Bayesian-based FMEA approach for assessing maritime supply chain risks. Transport Res E 125:222–240
Yang S, Bian C, Li X, Tan L, Tang D (2018) Optimized fault diagnosis based on FMEA-style CBR and BN for embedded software system. The Int J Adv Manufact Technol 94(9–12):3441–3453
Yang S, Lu M, Liu B, Hao B (2009) A fault diagnosis model for embedded software based on FMEA/FTA and bayesian network. In: 2009 8th International Conference on Reliability, Maintainability and Safety, IEEE, pp 778–782
Yang Z, Bonsall S, Wang J (2008) Fuzzy rule-based Bayesian reasoning approach for prioritization of failures in FMEA. IEEE Trans Reliab 57(3):517–528
Yucesan M, Gul M (2019) Failure prioritization and control using the neutrosophic best and worst method. Gran Comput p 1–15.
Yucesan M, Gul M, Guneri AF (2021) A Bayesian network-based approach for failure analysis in weapon industry. J Therm Eng 7(2):222–229
Zadeh LA (1965) Fuzzy sets. Inform Control 8(3):338–353
Zarei E, Azadeh A, Khakzad N, Aliabadi MM, Mohammadfam I (2017) Dynamic safety assessment of natural gas stations using Bayesian network. J Hazard Mater 321:830–840
Zarei E, Khakzad N, Cozzani V, Reniers G (2019) Safety analysis of process systems using Fuzzy Bayesian Network (FBN). J Loss Prev Process Ind 57:7–16
Zhou Q, Thai VV (2016) Fuzzy and grey theories in failure mode and effect analysis for tanker equipment failure prediction. Saf Sci 83:74–79
Huang J, Li ZS, Liu HC (2017) New approach for failure mode and effect analysis using linguistic distribution assessments and TODIM method. Reliab Eng Syst Saf 167:302–309
Catelani M, Ciani, L, Venzi M (2018) Failure modes, mechanisms and effect analysis on temperature redundant sensor stage. Reliab Eng Syst Saf 180:425–433
Du Y, Lu X, Su X, Hu Y, Deng Y (2016) New failure mode and effects analysis: an evidential downscaling method. Qual Reliab Eng Int 32(2):737–746
Safari H, Faraji Z, Majidian S (2016) Identifying and evaluatinf enterprise architecture risks using FMEA and fuzzy VIKOR. J Intell Manuf 27(2):475–486
Lo HW, Liou JJ, Huang CN, Chuang YC (219) A novel failure mode and efect analysis model for machine tool risk analysis. Reliab Eng Syst Saf 183:173–183
Seiti H, Fathi M, Hafezalkotob A, Herrera-Viedma E, Hameed IA (2020) Develo** the modified R-numbers for risk-based fuzzy information fusion and its application to failure modes, effects, and system resilience analysis (FMESRA). ISA Trans
Zhao H, You JX, Liu HC (2017) Failure mode and effect analysis using MULTIMOORA method with continuous weighted entropy under interval-valued intuitionistic fuzzy environment. Soft Comput 21(18):5355–5367
Kutlu AC, Ekmekcioglu M (2012) Fuzzy failure modes and effects analysis by using fuzzy TOPSIS-based fuzzy AHP. Expert Syst Appl 39(1):61–67
Zhang H, Dong Y, **ao J, Chiclana F, Herrera-Viedma E (2020) Personalized individual semantics-based approach for linguistic failure modes and effects analysis with incomplete preference information. IISE Trans 52(11):1275–1296
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all the authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Yucesan, M., Gul, M. & Celik, E. A holistic FMEA approach by fuzzy-based Bayesian network and best–worst method. Complex Intell. Syst. 7, 1547–1564 (2021). https://doi.org/10.1007/s40747-021-00279-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40747-021-00279-z