Abstract
The effect of pre-existing precipitates on microstructure evolution, mechanical properties, and fracture behavior of Al-2 wt.%Cu alloy during accumulative roll-bonding (ARB) process was investigated. Aging treatment was done on Al-2 wt.%Cu alloy in order to produce the nano-particle size precipitates. The microstructure evolution was studied using transmission electron microscope and electron backscattering diffraction (EBSD), and mechanical properties were investigated using tensile test and Vickers microhardness measurements. The fine precipitates were formed after the aging process and improved the mechanical properties in the Aged-specimen compared to the solution-treated (ST) specimen. The EBSD analysis showed that the grain size after 6-cycle ARB process has decreased down to 650 and 420 nm for the ST-ARB and the Aged-ARB specimens, respectively. Also, with increasing the number of the ARB cycles, the fraction of HAGBs is increased in both the ST and Aged-specimens. It was found that as the number of cycles increased, the Vickers microhardness value and the yield strength and the tensile strength increased. The scanning electron microscope (SEM) images showed that as the number of the ARB cycles increased, the dimple size became smaller.
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig1_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig2_HTML.jpg)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig3_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig4_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig5_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig6_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig7_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig8_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig9_HTML.gif)
![](http://media.springernature.com/m312/springer-static/image/art%3A10.1007%2Fs11665-015-1800-y/MediaObjects/11665_2015_1800_Fig10_HTML.jpg)
Similar content being viewed by others
References
A. Azushima, R. Kopp, A. Korhonen, D.Y. Yang, F. Micari, G.D. Lahoti, P. Groche, J. Yanagimoto, N. Tsuji, A. Rosochowski, and A. Yanagida, Severe Plastic Deformation (SPD) Processes for Metals, Manuf. Technol., 2008, 57, p 716–735
R.B. Figueiredo and T.G. Langdon, Using Severe Plastic Deformation for the Processing of Advanced Engineering Materials, Mater. Trans., 2009, 50, p 1613–1619
R.Z. Valiev and T.G. Langdon, Principles of Equal-Channel Angular Pressing as a Processing Tool for Grain Refinement, Prog. Mater. Sci., 2006, 51, p 881–981
R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov, Bulk Nanostructured Materials from Severe Plastic Deformation, Prog. Mater. Sci., 2000, 45, p 103–189
M. Richert, Q. Liu, and N. Hansen, Microstructural Evolution Over a Large Strain Range in Aluminum Deformed by Cyclic-Extrusion–Compression, Mater. Sci. Eng. A, 1999, 260, p 275–283
Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai, Novel Ultra-high Straining Process for Bulk Materials-Development of the Accumulative Roll-Bonding (ARB) Process, Acta Mater., 1999, 47, p 579–583
E. Borhani, H. Jafarian, A. Shibata, and N. Tsuji, Texture Evolution in Al-0.2 mass% Sc Alloy during ARB Process and Subsequent Annealing, Mater. Trans., 2012, 53, p 1863–1869
P. Hidalgo-Manrique, C.M. Cepeda-Jiménez, A. Orozco-Caballero, O.A. Ruano, and F. Carreño, Evolution of the Microstructure, Texture and Creep Properties of the 7075 Aluminum Alloy During Hot Accumulative Roll Bonding, Mater. Sci. Eng. A, 2014, 606, p 434–442
E. Borhani, H. Jafarian, H. Adachi, D. Terada, and N. Tsuji, Annealing Behavior of Solution Treated and Aged Al-0.2wt% Sc Deformed by ARB, Mater. Sci. Forum., 2010, 667, p 211–216
E. Borhani, H. Jafarian, T. Sato, D. Terada, N. Miyajima, and N. Tsuji, Proceedings of 12th International Conference on Aluminum Alloys (Japan), 2010, p 2168
E. Borhani, H. Jafarian, D. Terada, H. Adachi, and N. Tsuji, Microstructural Evolution During ARB Process of Al-0.2 mass% Sc Alloy Containing Al3Sc Precipitates in Starting Structures, Mater. Trans., 2011, 53, p 72–80
H. Pirgazi, A. Akbarzadeh, R. Petrov, and L. Kestens, Microstructure Evolution and Mechanical Properties of AA1100 Aluminum Sheet Processed by Accumulative Roll Bonding, Mater. Sci. Eng. A, 2008, 497, p 132–138
S.H. Lee, Y. Saito, T. Sakai, and H. Utsunomiya, Microstructure and Mechanical Properties 6061 Aluminum Alloy Processed by Accumulative Roll Bonding, Mater. Sci. Eng. A, 2002, 325, p 228–235
N. Tsuji, T. Toyoda, Y. Minamino, Y. Koizumi, T. Yamane, M. Komatsu, and M. Kiritani, Microstructural Change of Ultrafine-Grained Aluminum During High-Speed Plastic Deformation, Mater. Sci. Eng. A, 2003, 350, p 108–116
J.M. Silcock, T.J. Heal, and H.K. Hardy, Structural Aging Characteristics of Binary Aluminium–Copper Alloys. J. Inst. Met. 1953–1954, 82, p 239–248
M. Murayama, Z. Horita, and K. Hono, Microstructure of Two-Phase Al-1.7 at% Cu Alloy Deformed by Equal-Channel Angular Pressing, Acta Mater., 2001, 49, p 21–29
X. Huang, N. Tsuji, N. Hansen, and Y. Minamino, Microstructural Evolution During Accumulative Roll-Bonding of Commercial Purity Aluminum, Mater. Sci. Eng. A, 2003, 340, p 265–271
B.G. Clark, I.M. Robertson, L.M. Dougherty, D.C. Ahn, and P. Sofronis, High-Temperature Dislocation-Precipitate Interactions in Al Alloys: An In Situ Transmission Electron Microscopy Deformation Study, Mater. Res., 2005, 20, p 1792–1801
F.J. Humphreys and P.B. Hirsch, Work-Hardening and Recovery of Dispersion Hardened Alloys, Philos. Mag., 1976, 34, p 373–390
F.J. Humphreys, Local Lattice Rotations at Second Phase Particles in Deformed Metals, Acta Metal., 1979, 27, p 1801–1814
P.J. Apps, J.R. Bowen, P.B. Prangnell, Nanomaterials by Severe Plastic Deformation-NANSPD2, M. Zehetbauer, R.Z. Valiev, Eds., Vienna, Austria, 2002, p 138
P.J. Apps, J.R. Bowen, and P.B. Prangnell, The Effect of Coarse Second-Phase Particles on the Rate of Grain Refinement During Severe Deformation Processing, Acta Mater., 2003, 51, p 2811–2822
B.K. Min, H.W. Kim, and S.B. Kang, Effect of Al3Sc Precipitate on the Microstructural Evolution During Accumulative Roll Bonding in Al–0.2 wt.% Sc Alloy, J. Mater. Process. Technol., 2005, 162–163, p 355–361
S.G. Jia, M.S. Zheng, P. Liu, F.Z. Ren, B.H. Tian, G.S. Zhou, and H.F. Lou, Aging Properties Studies in a Cu–Ag–Cr Alloy, Mater. Sci. Eng. A, 2006, 419, p 8–11
R.E. Smallman and R.J. Bishop, Metals and Materials: Science, Processes, Applications, Butterworth-Heinemann, Oxford, 1995
S.Y. Hu, M.I. Baskes, M. Stan, and L.Q. Chen, Atomistic calculations of interfacial energies, nucleus shape and size of θ′ precipitates in Al–Cu alloys, Acta Mater., 2006, 54, p 4699–4707
I. Gutierrez-Urrutia, M.A. Mu˜noz-Morris, and D.G. Morris, The Effect of Coarse Second-Phase Particles and Fine Precipitates on Microstructure Refinement and Mechanical Properties of Severely Deformed Al Alloy, Mater. Sci. Eng. A, 2005, 394, p 399–410
Z. Horita, K. Oh-ishi, and K. Kaneko, Microstructure control using severe plastic deformation, Sci. Tech. Adv. Mater., 2006, 7, p 649–654
J. Rosler, H. Harders, and M. Baker, Mechanical Behaviour of Engineering Materials: Metals, Ceramics, Polymers and Composites, Springer, Berlin, 2007
J. Wang, I.J. Beyerlein, A. Misra, S.M. Valone, and T.C. Germann, Atomistic Modeling of Dislocation-Interface Interaction, 3rd International Conference on Heterogeneous Material Mechanics, May 22–26 (Shanghai, China), 2011
ASM, ASM Metals Handbook Fractography, Vol 12, ASM, Metals Park, 1987
R.W. Hertzberg, Deformation and Fracture Mechanics of Engineering Materials, 3rd ed., John Wiley & Sons Inc., Singapore, 1989
B. Azad, E. Borhani, and H.R. Mohammadian Semnani, Fracture Behavior of Al-0.2wt%Zr Alloy Processed by Accumulative Roll Bonding (ARB) Process, Kovove Mater., 2015 (in press)
ChVA Narasayya, P. Rambabu, M.K. Mohan, R. Mitra, and N.E. Prasad, Tensile Deformation and Fracture Behaviour of an Aerospace Aluminium Alloy AA2219 in Different Ageing Conditions, Proc. Mater. Sci., 2014, 6, p 322–330
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Azad, B., Borhani, E. The Effect of Al2Cu Precipitate Size on Microstructure and Mechanical Properties of Al-2 wt.%Cu Alloys Fabricated by ARB. J. of Materi Eng and Perform 24, 4789–4796 (2015). https://doi.org/10.1007/s11665-015-1800-y
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-015-1800-y