Abstract
The human hands represent an intricate engineering, exquisitely to carry out a variety of tasks. Mimicking human hand is the most challenging task due to the complex structure while, considering the tasks performed by hand. Develo** hand prosthesis requires modeling of human hand and the study of its motion capabilities. A human hand model presented in this paper resembles anatomical hand, considering its restrictions and similar motions of the human hand. A 3D model of prosthetic hand that is similar to structure of an adult hand is created using CATIA software. The trajectories and motion of hand model are derived by Simscape toolbox in MATLAB environment. The deformation and strain distribution is obtained using ANSYS software to ensure that hand model will be able to withstand the load it is intended to. Thus the model ratifies for the maximum load and the deformation it would experience on the application of load.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Schwarz, R.J., Taylor, C.L.: The anatomy and mechanics of the human hand. Artif. Limbs 2(2), 22–35 (1955)
Ungureanu, L., Dragulescu, D.: Modeling a human finger as an automatic system. In: 11th International Conference on Vibration Engineering, Timisoara, Romania, 27–30 September 2005
Yang, J., Pitarch, E.P., Abdel-Malek, K., Patrik, A., Lindkvist, L.: A multi-fingered hand prosthesis. Mech. Mach. Theory 39, 555–581 (2004)
Rakibul, H., Vepar, S.H., Hujijbert, H.: Modeling and control of the Barrett hand for gras**. In: 15th International Conference on Computer Modelling and Simulation. Cambridge University, Cambridge, 10–12 April 2013
Vavrinčíková V., Hroncová D.: Modeling of robot dynamics in the SimMechanics environment. ATP J. Plus Intell. Motion Syst. 60–64 (2009). ISSN 1336-5010 (in Slovak)
Dung, L.T., Kang, H.-J., Ro, Y.-S.: Robot manipulator modeling in matlab-SimMechanics with PD control and online gravity compensation. In: Proceedings of the 5th IEEE International Forum on Strategic Technology, IFOST 2010, 13–15 October 2010
Boros, T., Lamár, K.: Six-axis educational robot workcell with integrated vision system. In: Proceedings of 4th IEEE International Symposium on Logistics and Industrial Informatics LINDI 2012, Smolenice, Slovakia, pp. 239–244 (2012). ISBN 978-1-4673-4518-7
Fedák, V., Ďurovský, F., Üveges, R.: Analysis of robotic system motion in SimMechanics and MATLAB GUI environment. In: MATLAB Applications for the Practical Engineer. InTech (2014). https://doi.org/10.5772/58371
Ungureanu, L., Drăgulescu, D.: Modeling a human finger as an automatic system. In: Proceedings of SACI, pp. 69–75 (2005)
Serbest, K., Cilli, M., Yildiz, M.Z., Eldogan, O.: Development of a human hand model for estimating joint torque using MATLAB tools. In: 2016 6th IEEE International Conference on Biomedical Robotics and Biomechatronics (BioRob), June, pp. 793–797. IEEE, New York (2016)
Tasar, B., Gulten, A., Yakut, O.: Modeling, simulation and control of prosthetic hand using SimMechanics. Int. J. Curr. Eng. Technol. 8(2), 206–212 (2018)
Bahadur, R., Mahmood, A.: Prosthetic hand module using electromechanical actuators: a simulation. In: 2016 19th International on Multi-topic Conference (INMIC), December, pp. 1–5. IEEE, New York (2016)
Hota, R.K., Korrapati, M., Kumar, C.S.: Kinematic design of a linkage driven robotic hand for prosthetics capable of achieving ten grips. In: 2016 International Conference on Robotics and Automation for Humanitarian Applications (RAHA), December, pp. 1–6. IEEE, New York (2016)
Lealndash, J.A., Torres-San Miguel, C.R., Carbajalndash, M.F., Martinez-Saez, L.: Structural numerical analysis of a three fingers prosthetic hand prototype. Int. J. Phys. Sci. 8(13), 526–536 (2013)
Stanciu L., Stanciu, A.: Designing and implementing a human hand prosthesis. In: Vlad S., Ciupa R.V., Nicu A.I. (eds) International Conference on Advancements of Medicine and Health Care through Technology. IFMBE Proceedings, vol 26. Springer, Berlin, Heidelberg (2009). https://doi.org/10.1007/978-3-642-04292-8_88
Human Anatomy Library: Anatomy of the left hand (2016). http://humananatomylibrary.com/anatomy-of-the-left-hand/anatomy-of-the-left-hand-3d-human-anatomy-model-human-anatomy-library/
Dragulescu, D., Ungureanu, L.: Human hand modeling. Al II-lea Simpozion Internaţional de Mecanică Teoretică şi Aplicată “Dimitrie Mageron”, Iasi, pp. 365–372 (2005)
Ungureanu, L., Stanciu, A.: Modeling the motion of the human hand. In: The 11th International Conference on Vibration Engineering, Timişoara, pp. 111–116 (2005)
Ungureanu, L., Stanciu, A., Menyhardt, K.: Actuating a human hand prosthesis: model study. In: 2nd WSEAS International Conference on Dynamical Systems and Control, Bucharest Romania (October 2006)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Savithri, C.N., Kevin, R., Priya, E. (2019). A Preliminary Study on Kinematic Analysis of Human Hand. In: Hemanth, J., Silva, T., Karunananda, A. (eds) Artificial Intelligence. SLAAI-ICAI 2018. Communications in Computer and Information Science, vol 890. Springer, Singapore. https://doi.org/10.1007/978-981-13-9129-3_1
Download citation
DOI: https://doi.org/10.1007/978-981-13-9129-3_1
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-9128-6
Online ISBN: 978-981-13-9129-3
eBook Packages: Computer ScienceComputer Science (R0)