Search
Search Results
-
Variation of Cutting Forces with Different Cutting Parameters and Tool Wear during Turning of 9442-Nickel-Aluminum Bronze
Nickel-aluminum bronze alloys are prone to tool surface bonding and wear on the tool substrate during the cutting process. The correlation between...
-
Optimization of Cutting Parameters for Cubic Boron Nitride Tool Wear in Hard Turning AISI M2
In the hard turning process of AISI M2, due to its high hardness and high strength, the tool wear is serious. Tool wear seriously restricts the...
-
Surface Integrity, Tool Wear, and Chip Morphology Studies in Spot Cooled Vibration Assisted Turning of Ti6Al4V Alloy
Surface integrity in the machining of Titanium alloys is of prime importance as they directly influence the service life of the machined component....
-
A systematic analysis of maximum tolerable tool wear in friction stir welding
Friction stir welding (FSW) is a solid-state joining process with a wide range of applications in the E-mobility, automotive, aerospace and energy...
-
Optimization of Residual Stresses, Tool Wear, and Material Removal Rate of Tempered EN-36C Alloy Steel in CNC Turning Using Response Surface Methodology
In the manufacturing industry, it is a great challenge to achieve residual stress-free products from hard metals and alloys. Optimum selection of...
-
Experimental Investigation and Optimizing of Turning Parameters for Machining of Al7075-T6 Aerospace Alloy for Reducing the Tool Wear and Surface Roughness
The current work presents an approach for the optimization of machining parameters on the turning of Al7075-T6 aerospace alloy. The alloy was turned...
-
Characterization and Modeling of Wear Behavior of AISI D3 Tool Steel under Dry Sliding Conditions
In this study, central composite design (CCD) and response surface methodology (RSM) were employed to model the wear behavior of AISI D3 tool steel....
-
Niobium Carbide Coatings Grown on Cold Work Tool Steel AISI D3 by Thermomechanical Processing: Characterization, Wear and Corrosion Behaviors
AbstractIn this study, niobium carbide (NbC) coatings were grown on AISI D3 cold work tool steel via thermoreactive diffusion (TRD) at 900, 1000 and...
-
Drilling of GFRP with Liquid Silicon Rubber Reinforced with fine Aluminium Powder on Hole Surface Quality and Tool Wear using DOE
The efforts are made to study the effect of machining parameters: speed, feed, tool tip angle, and tool material on hole quality: surface finish, and...
-
Influence of Heat and Cryogenic Treatments on the Abrasive Wear Behavior of H13 Tool Steel
This study analyzes the influence of cryogenic treatments, before the pre-tempering treatment on the microstructure, and the mechanical properties of...
-
Effects of Shallow and Deep Cryogenic Treatment on Tool Flank Wear and Surface Roughness in Machining 41Cr4 Steel
This study presents the affects of cryogenic treatment on flank wear (Vb) and surface roughness (Ra) in machining 41Cr4 steel with shallow (SCT (15 h...
-
Quantitative Evaluation of Tool Wear in Cold Stam** of Ultra-High-Strength Steel Sheets
The body of an automobile must be lightweight and crash-worthy. The use of advanced high-strength steel reduces the manufacturing cost for automobile...
-
Effects of the Ultrasonic Surface Rolling Process on the Surface Integrity, Wear Resistance, and Corrosion Resistance of 4Cr5MoSiV1 Tool Steel Before and After Quenching
Quenched 4Cr5MoSiV1 tool steel is commonly used as a material for tablet presser dies. However, it exhibits high sensitivity to temperature and...
-
Wear Mechanisms/Models
The surfaces are continuously damaged by wear. Friction always leads to wear. According to statistics, wear, fatigue, and corrosion are the three... -
Research on the friction and wear characteristics of V-groove unidirectional convergent gradient texture on carbide tool surface
The reverse fluid model of V-groove texture was established by SOLIDWORKS. The textures of bionic arrangement and symmetrical arrangement and 3°, 5°,...
-
The Wear
Understanding the approaches to wear degradation, forecasting, and reducing wear are some of the most challenging tasks for an engineer.... -
Elevated Temperature Plasma Nitriding of CrMoV Tool Steel for the Enhancement of Hardness and Wear Resistance
Elevated temperature plasma nitriding of Cr-Mo-V-based tool steel was performed by varying the treatment time to enhance hardness and wear...
-
Relative Tool Wear and Metal Removal Studies in Electric Discharge Machining of AISI D2 Die Steel Using Cu-Cr-Zr, Cu-Cd, and Cu-Be Electrode Materials
Performance evaluation of electrode material in terms of metal removal rate and relative electrode wear is very much essential to assess the quality...
-
Microstructure–Wear Resistance Relationship of Nitrogen-Containing High-Speed Tool Steel, AISIM41: Non-equilibrium Solidification
This research work highlights the influence of nitrogen as an alloying element on the morphology, type, and amount of phases and their turns on...
-
A PCA-Integrated OGM (1, N) Predictive Model for In-Process Tool Wear Prediction Based on Continuous Monitoring of Multi-Sensorial Information
In the modern machining process, catastrophic tool failure has become a significant problem because the machining quality and efficiency depend on...