Search
Search Results
-
An alternative approach for the determination of electromechanical parameters of a tubular linear induction motor and its experimental validation
This paper presents an alternative approach for offline parameter estimation of a 3-phase, 500 W, 2.5 m/s, 4-pole tubular linear induction motor...
-
Optimised design, analysis, fabrication and experiments on a tubular linear induction motor prototype
This paper presents optimised design, analysis and fabrication of a 500 W, 2.5 m/s, 4-pole tubular linear induction motor (TLIM) prototype with a...
-
Distributed velocity-free formation tracking control for clustered UAVs under virtual leader-follower framework
The collective formation control problem of a cluster of rotorcraft unmanned aerial vehicles (UAVs) is investigated in this article. The consensus...
-
Calculation of the Characteristics of a Two-Inductor Linear-Induction Motor (Asynchronous Motor)
AbstractA calculation model of a two-inductor linear asynchronous motor with two identical inductors located opposite each other and a secondary...
-
Probabilistic Assessment of the Performance of a Power Plant Equipment’s Emergency Conditions Early Detection Model Based on the Least Potentials Method
Abstract—This article is a continuation of the previously published paper [1], which describes a technique developed at OOO Incontrol on the basis of...
-
Box–Behnken based investigation of surface quality and tool wear rate and FEM analysis of tool wear in TiAlN/CrN coated carbide tool
The quantitative effects of cutting speed, feed and depth of cut on surface quality of the turned 316 LVM stainless steel work piece and tool wear of...
-
Develo** Systems of Manufacturing Tolerances
AbstractSystems of tolerances for different operating conditions of machine tools are presented for use in diagnostic assessment of the reliability...
-
Tracking controller design for air handling units with uncertainties
As an important component of the heating, ventilating and air conditioning (HVAC) systems, air handling units (AHUs) are responsible for regulating...
-
Mauerwerksbau
Die im Mauerwerksbau am häufigsten nachzuweisenden Bauteile sind Wände unter vertikaler Belastung, Schubwände und Kellerwände. Die beim Nachweis...
-
Subtransmission overhead lines mechanical monitoring for fast detection of damaging events
Different harmful events affecting high voltage overhead lines (OHLs) cause changes in the mechanical tension (tensile strength) of conductors. A...
-
Fire Behaviour of a Prestressed Thin-Walled Concrete V-Beam
The present work investigates the fire behaviour of a prestressed thin-walled concrete V-beam with variable cross section along its longitudinal...
-
A Multi-objective Two-sided Disassembly Line Balancing Optimization Based on Artificial Bee Colony Algorithm: A Case Study of an Automotive Engine
Disassembly is an important part of green manufacturing and remanufacturing. The disassembly line is an optimum form for mass and automatic...
-
Linear Control Gain for Synthetic Inertia of a PMSG-Based Wind Turbine Generator
This paper proposes a synthetic inertia control (SIC) scheme for a permanent-magnet synchronous generator-based wind turbine generator (WTG). The...
-
Static Properties of Plain Journal Bearing
The phenomenon of occurrence of a hydrodynamic oil film on the bearing system is analyzed. A theoretical model of the radial slide bearing system...
-
Utilization of Atlantic Salmon By-product Oil for Omega-3 Fatty Acids Rich 2-Monoacylglycerol Production: Optimization of Enzymatic Reaction Parameters
AbstractThe research work was aimed to produce 2-monoacylglycerol rich omega-3 polyunsaturated fatty acids from supercritical carbon dioxide (SC-CO 2 )...
-
7 Innovation Approach to Reduced Order Estimation
In this chapter we will rederive some of the results that have been previously obtained in Chapter three using a concept of “reduced order innovation...
-
Calculation of the Underground Structure at Limit States
The large number of heterogeneous factors that determine the design scheme, the construction of which should be based on a combination of...
-
Cracking Resistance of Glass in Terms of the Principles of Fracture Mechanics
The basic principles of subcritical crack growth (SCG) are developed based on linear elastic fracture mechanics (LEFM) and dynamic crack growth...
-
The Flow Boiling Crisis of Saturated Water in Pipes at High Pressures
AbstractThe procedures developed by the authors for calculating the distribution of the liquid over the channel cross section in the...
-
Research on LADRC strategy of PMSM for road-sensing simulation based on differential evolution algorithm
A linear active disturbance rejection control (LADRC) strategy for permanent magnet synchronous motor (PMSM) for road-sensing based on the...
