Abstract
The fault of power circuit breaker (PCB) can lead very serious problems, especially in high voltage–power grid. The structure of contacts may be composed of main contacts and arc contacts, and this structure can avoid ablation of main contacts efficiently. It is necessary to study the eroded state of the arc contacts and the dynamic contact resistance of arc contacts to estimate the operating state of the PCB. The wear of contacts contains arc ablation and mechanical wear through the characteristics of contacts. The arc ablation is caused by the high temperature of the arc and the mechanical wear is caused by the mechanical friction of static and movable contacts. Some experiments have been done under different size of contacts and different current through them. The results show that the mechanical wear increases, sometimes heavier, with the increase of the size of fixed contacts and the decrease of the size of movable ones because the force between fixed and movable contacts becomes larger. The results also show that the ablation of arc contacts increases with the increase of current, especially when the current is up to 20 kA. With the high temperature of arc reaching the hardness point of copper, the arc ablation and mechanical erosion are increasing obviously since the contacts become soft and easy to wear. Another result of the study shows it is important to choose the material of contacts and the force between movable and fixed contacts. The harder and less resistance the material of contacts, the better the operating situation. To monitor the operating situation of the breaker, the dynamic contact resistance was measured 25 times. As a result, the dynamic contact resistance is sensitive to the current and increasing with the increase of continuous experiment time because of the increasing of metal ions. Furthermore, if the SF6 in the PCB is changes, the dynamic contact resistance would be changed. The dynamic contact resistance in this experiment varies substantially within the range of 80–250 μΩ at the current of 20 kA.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Can D, **chao Y, Zhibing L (2014) Contact erosion characteristics in making process of SF6 circuit breakers. High Volt Eng 40(10):3228–3234
Baiming C, Zhengyu Z, **aobin L (2010) Effects of W content on tribological properties of Cu-based friction composites. J Mater Sci Eng 28(1):69–75
Shaoyi GUO, Bingliang YE, Yingqi TAO et al (2006) Tribological behavior of CuCr contact materials. Chin J Nonferrous Metals 16(12):2071–2076
de Souza RT, da Costa EG, Deliveira AC (2014) Characterization of contacts degradation in circuit breakers through the dynamic contact resistance. In: Transmission and distribution conference and exposition-latin America, Medellin, Colombia, IEEE, pp 1–5
de Souza RT, da Costa EG, de Araújo JF (2014) A system for dynamic contact resistance with arduino platform on MV and HV circuit breaker. In: Instrumentation and measurement technology conference (I2MTC) proceedings, Montevideo, Uruguay, IEEE, pp 369–373
Jeyaraj SG (2011) Effective and efficient circuit breaker analysis. IET conference on reliability of transmission and distribution networks (RTDN 2011), London, IET, pp 1–6
Greenwood JA (1966) Williamson JBP (1966) Contact of nominally flat surfaces. Proc R Soc Ser A Math Phys Sci 295:300–319
Michel L, Olivier T, Fouad B et al (2008) A complete strategy for conducting dynamic contact resistance measurements on HV circuit breakers. IEEE Trans Power Deliv 23(2):710–716
Landry M, Mercier A, Ouellert G et al (2006) A new measurement method of the dynamic contact resistance of HV circuit breakers. In: IEEE PES transmission and distribution conference and exposition Latin America. Venezuela, IEEE, pp 1002–1009
Simanand GJ (2011) Effective and efficient circuit breaker analysis. In: IET conference on reliability of transmission and distribution networks, IET, London, pp 1–6
Li L, Ding W, Shi Y (2002) Dynamic resistance measurement: a new method for online condition assessment of SF6 circuit breaker. High Volt Apparatus 2002-02:54–55
**nglei C, Xue Z, Guofu Z (2018) Electrical life span prediction of HVDC relay based on the accumulated arc erosion mass. IEEE Trans Compon Pack Manuf Technol 8(3):356-363
Gong C, Lei L, Zhuohong P (2017) Electrical erosion test and condition assessment of SF6 CB contact sets. IET Gen Trans Distrib 11:1901–1909
Yakui L, Guogang Z, Hao Q (2018) Prediction of the dynamic contact resistance of circuit breaker based on the kernel partial least squares. IET Gen Trans Distrib 12:1815
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
**ng, L., Zhang, X., Tong, Q. et al. Study of Ablation of Arc Contacts and Dynamic Contact Resistance in High Current Breaker. J. Electr. Eng. Technol. 15, 1015–1023 (2020). https://doi.org/10.1007/s42835-020-00381-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42835-020-00381-1