Abstract
A comprehensive study on Sn macrosegregation behavior in ternary Al-Sn-Cu alloys was carried out by comparative analysis between gravity casting and squeeze casting samples. The microstructure and Sn distribution of the castings were characterized by metallography, scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, and a direct reading spectrometer. Results show that there are obvious differences in Sn morphology between gravity casting and squeeze casting alloys. Under squeeze casting condition, the grain size of the casting is smaller and the distribution of β(Sn) is uniform. This effectively reduces the segregation of triangular grain boundary as well as the segregation of Sn. The segregation types of Sn in gravity casting and squeeze casting samples are obviously different. The upper surfaces of gravity casting samples show severe negative segregation, while all the lower surfaces have positive segregation. Compared with gravity casting, squeeze casting solidifies under isostatic pressure. Due to the direct contact between the upper surface of the casting and the mold, the casting solidifies faster under higher undercooling degree and pressure. Consequently, the uniform distribution of Sn reduces the segregation phenomenon on the surface of the casting.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ratke L, Diefenbach S. Liquid immiscible alloys. Materials Science and Engineering, 1995, 15R: 263–347.
Ratke L. Immiscible liquid metals and organic. Germany: DGM Informations GmbH, 1993: 199–258.
Davis J R. Aluminum and aluminum alloys. ASM International, 1993: 351–416.
Zhai W, Hu L, Geng D L, et al. Thermodynamic properties and microstructure evolution of ternary Al-10%Cu-x%Sn immiscible alloys. Journal of Alloys and Compounds, 2015, 627: 402–409.
Kaban, Curiotto I, Chatain S, et al. Surfaces, interfaces and phase transitions in Al-In monotectic alloys. Acta Materialia, 2010, 58: 3406–3414.
Fang X W, Fan Z Y. Rheo-diecasting of Al-Si-Pb immiscible alloy. Scripta Materialia, 2006, 54: 789–793.
Bertelli F, Brito C, Ferrdira I L, et al. Cooling thermal parameters, microstructure, segregation and hardness in directionally solidified Al-Sn-(Si, Cu) alloys. Materials and Design, 2015, 72: 31–42.
Yan Y J, Wei C, He Y X, et al. Effect of high magnetic field on solidification microstructure evolution of a Cu-Fe immiscible alloy. China Foundry, 2022, 19(4): 335–341.
Wang F, Choudhury A, Selzer M, et al. Effect of solutal Marangoni convection on motion, coarsening, and coalescence of droplets in a monotectic system. Physical Review E, 2012, 86(6–2): 066318.
Mirkovicć D, Grobner J, Schmid-Fetzer R. Liquid demixing and microstructure formation internary Al-Sn-Cu alloys. Materials Science and Engineering A, 2008, 487: 456–467.
Li W, Jiang H X, Zhang L L, et al. Solidification of Al-Bi-Sn immiscible alloy under microgravity conditions of space. Scripta Materialia, 2019, 162: 426–431.
Kotadia H R, Doernberg E, Patel J B, et al. Solidification of Al-Sn-Cu based immiscible alloys under intense shearing. Metallurgical and Materials Transactions A, 2009, 40: 2202–2211.
Zhai W, Wang B J, Hu L Z, et al. Three orthogonal ultrasounds fabricate uniform ternary Al-Sn-Cu immiscible alloy. Scientific Reports, 2016, 6(1): 36718.
Guo K L, ** Technology, 2010, 35(1): 70–74. (In Chinese)
Kim H H, Kang C G. Numerical simulation and experimental study for rheo-forged component using direct and indirect die system. Transactions of Nonferrous Metals Society of China (English), 2010, 20(9): 1799–1804.
Zhang H Y, **ng S M, Zhang Q H. Evaluation of the mold-filling ability of alloy melt in squeeze casting. Journal of University of Science and Technology Bei**g: Mineral Metallurgy Matenals (Eng. Ed.), 2006, 13(1): 60–66.
Zhang X L, Wang T M, Li T J, et al. Numerical study on rheocasting A356 alloy using cooling slope method. The 7th Pacific Rim International Conference on Modeling of Casting and Solidification Process (MCSP7-2007), Dalian, 2007: 643–648.
Yang X R, Xu X D, Liu P. Effect of vertical bending pouring channel on the microstructure of semisolid state A356 alloy feed stock. Shanxi Metallurgy, 2013, 36: 14–17. (In Chinese)
Yang X R, Sun B Y, Huang Q X, et al. Preparation of semisolid feedstock by reversed cone channel pouring. Advanced Materials Research, 2012, 535–537: 2606–2609.
Guo H M, Yang X J, Hu B. Low superheat pouring with a shear field in rheocasting of aluminum alloys. Journal of Wuhan University of Technology — Materials Science Edition, 2008, 23: 54–59.
Li X M, Wang Y, Bi Q C. Experimental study on gas bubble rising velocity in different liquids. Journal of **’an Jiaotong University, 2003, 37: 971–974.
Liu W, **ng S M, Bao P W. Energy dissipation and apparent viscosity of semisolid metal during rheological processes Part II: Apparent viscosity. Journal of Materials Science and Technology, 2007, 23: 801–805.
Liu W, **ng S M, Bao P W, et al. Energy dissipation and apparent viscosity of semisolid metal during rheological processes Part I: Energy dissipation. Journal of Materials Science & Technology, 2007, 23(3): 342–346.
Zhong Y, Yan D S, Su G Y, et al. Microsegregation and improvement of LYl2 alloy by squeeze casting. Acta Metallurgica Sinica, 2001, 37(1): 42–46. (In Chinese)
Chen F Y, Jie W Q. Experimental study on microstructure segregation of Al-Cu-Zn Alloy and Scheil Model. Acta Metallurgica Sinica, 2004, 40(6): 664–668.
Jie W Q, Zhou Y H. Formation of hot-top segregation in steel ingot and effect of steel compositions. Metallurgical and Materials Transactions B, 1989, 5(20): 723–730.
Liu J L, Zhao Y Q, Zhou L. Segregation of Ti-2.5Cu, Ti-3Fe and Ti-3Cr alloy ingot. Rare Metal Materials and Engineering, 2004, 33(7): 731–735.
Lee S G, Patel G R, Gokhale A M. Inverse surface macrosegregation in high-pressured die-cast AM60 magnesium alloy and its effects on fatigue behavior. Scripta Materialia, 2005, 52(10): 1063–1068.
Lappa M. Fluids, materials, and microgravity-numerical techniques and insights into physics. Oxford: Elsevier Ltd., 2004.
Young N O, Goldstein J S, Block M J. Journal of Fluid Mechanics, 1959, 6: 350–356.
Ghomashchi M R, Vikhrov A. Squeeze casting: An overview. Journal of Materials Processing Technology, 2000, 101(1–3): 1–9.
Wang F F, Ma Q X, Meng W, et al. Experimental study on the heat transfer behavior and contact pressure at the casting-mold interface in squeeze casting of aluminum alloy. International Journal of Heat and Mass Transfer, 2017, 112: 1032–1043.
Flemings M C. Our understanding of macrosegregation past and present. ISIJ International, 2000, 40(9): 833–841.
Acknowledgements
This research was financially supported by the National Natural Science Foundation of China (No. 51575151) and the Science and Technology Project of Anhui Province, China (No. 1501021006).
Author information
Authors and Affiliations
Corresponding author
Additional information
Conflict of interest
The authors declare that they have no conflict of interest.
Yan-guo Yin Male, Professor. Research interests: Lead-free environment-friendly self-lubricating materials, aviation lightweight materials, critical hydraulic friction pair components.
Rights and permissions
About this article
Cite this article
Xu, M., Yin, Yg., Li, Cm. et al. A comparative study on Sn macrosegregation behavior of ternary Al-Sn-Cu alloys prepared by gravity casting and squeeze casting. China Foundry 20, 63–70 (2023). https://doi.org/10.1007/s41230-023-2046-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41230-023-2046-1