Abstract
Compared to traditional plasma cladding technology, plasma spray melting technology is characterized by a small heat-affected zone and high processing speed, and has a high application value. However, the process still faces significant problems, such as inaccurate parameters and work points and feasibility that need to be investigated. This study discusses a two-dimensional (2D) model of the plasma spray melting process to provide a theoretical basis for determining the optimal process parameters. The spray melting process was studied in depth by considering the cooling effect of gas convection on the melting pool, as well as by the analysis of thermal cycling and thermal diffusion of the matrix. Finally, the reliability of the model was validated by a Ni60 coating with micro-metallurgical bonding characteristics, which was spray melted onto the surface of a Q235 steel matrix. Due to its characteristics of low power, fast heating, and fast cooling, plasma spray melting technology can be used to prepare various thin coatings with micro-metallurgical bonding on the die surface, so as to significantly improve the bonding strength of the coating and mitigate the influence of the heat of the spray melting process on the die, thereby improving the material performance.
Similar content being viewed by others
References
X. Binshi, Remanufacture Engineering and Its Development in China, China Surf. Eng., 2010, 23(2), p 6.
M. Lieder and A. Rashid, Towards Circular Economy Implementation: a Comprehensive Review in Context of Manufacturing Industry, J. Clean. Prod., 2016, 115, p 36-51.
J. Guo, L. Yang, X. Cui et al., Characterization of High-Temperature Mechanical Properties of Plasma-Cladded Coatings with Thermo-Mechanical Coupling, Mater. Charact., 2018, 145, p 196-204.
W. **feng, J. Zirun, Y. Wei et al., Effect of Laser Cladding and Plasma Cladding on Microstructure and Properties of Nickel-Based Alloy Cladding Layer, Mater. Protect., 2020, 53(1), p 80-83.
K. Simunovic, S. Havrlisan, T. Saric et al., Modeling and Optimization in Investigating Thermally Sprayed Ni-Based Self-Fluxing Alloy Coatings: A Review, Materials, 2020, 13(20), p 4584.
O.G. Devojno, E. Feldshtein, M.A. Kardapolava et al., On the Formation Features, Microstructure and Microhardness of Single Laser Tracks Formed by Laser Cladding of a NiCrBSi Self-Fluxing Alloy, Opt. Lasers Eng., 2018, 106, p 32-38.
A. Piasecki, M. Kulka and M. Kotkowiak, Wear Resistance Improvement of 100CrMnSi6-4 Bearing Steel by Laser Boriding using CaF2 Self-Lubricating Addition, Tribol. Int., 2016, 97, p 173-191.
A. Jh, A. By, A. Hji et al., Microstructural Evolution of the Heat Affected Zone of a Co-Ti-W Alloy Upon Laser Cladding with a CoNiCrAlY Coating-ScienceDirect, Mater. Charact., 2019, 158, p 109998.
Y.X. Zhou, J. Zhang, Z.G. **ng et al., Microstructure and Properties of NiCrBSi Coating by Plasma Cladding on Gray Cast Iron, Surf. Coat. Technol., 2018, 361, p 270-279.
V.G. Efremenko, Y.G. Chabak, K. Shimizu et al., Structure Refinement of High-Cr Cast Iron by Plasma Surface Melting and Post-heat Treatment, Mater. Des., 2017, 126, p 278-290.
T. Zhu, H. Wang, S. Sun, J. Geng and Y. Shen, Numerical Simulation of Constricted and Diffusive Arc–Anode Attachments in Wall-Stabilized Transferred Argon Arcs, Plasma Sci. Technol, 2019, 21(12), p 57-66.
J.A. Robert Jayachandran and N. Murugan, Investigations on the Influence of Surfacing Process Parameters Over Bead Properties During Stainless Steel Cladding, Mater. Manuf. Process., 2012, 27(1), p 69-77.
P. Fauchais, M. Vardelle and S. Goutier, Atmospheric Plasma Spraying Evolution Since the Sixties Through Modeling, Measurements and Sensors, Plasma Chem. Plasma Process., 2017, 37(3), p 1-26.
W.Y. Li, D.D. Zhang, C.J. Huang et al., Modelling of Impact Behaviour of Cold Spray Particles, Surf. Eng., 2014, 30(5), p 299-308.
T. DebRoy, H.L. Wei, J.S. Zuback et al., Additive Manufacturing of Metallic Components–Process, Structure and Properties, Prog. Mater Sci., 2018, 92, p 112-224.
T. Coors, F. Pape, J. Kruse et al., Simulation Assisted Process Chain Design for the Manufacturing of Bulk Hybrid Shafts with Tailored Properties, Int. J. Adv. Manuf. Technol., 2020, 108(7), p 2409-2417.
A. Douce, C. Delalondre, H. Biausser et al., Numerical Modelling of an Anodic Metal Bath Heated with an Argon Transferred Arc, ISIJ Int., 2003, 43(8), p 1128-1135.
P. Kumar, N.K. Jain and M.S. Sawant, Modeling of Dimensions and Investigations on Geometrical Deviations of Metallic Components Manufactured by μ-plasma Transferred Arc Additive Manufacturing Process, Int. J. Adv. Manuf. Technol., 2020, 107(7), p 3155-3168.
B. Song, T. Yu, X. Jiang et al., Numerical Model of Transient Convection Pattern and Forming Mechanism of Molten Pool in Laser Cladding, Num. Heat Trans. Part A Appl., 2019, 75(12), p 855-873.
Y. Wenyuan, J. **aofang, L. Li et al., Thermal Simulation Experiments on Scrap Melting, Iron Steel, 2017, 52(3), p 27-35.
W. Wang, J. Jia, C. **uquan et al., Numerical Simulation of Residual Stress and Deformation of Q235 Steel by Plasma Cladding, Special Cast. Nonferrous Alloys, 2020, 40(9), p 975-979.
G. Jianqiang, Numerical Simulation of Residual Stress in Laser Cladding, Zhejiang University of Technology, Zhejiang, 2010.
W. Wang, M. Rong, J. Yan et al., The Reactive Thermal Conductivity of Thermal Equilibrium and Nonequilibrium Plasmas: Application to Nitrogen, IEEE Trans. Plasma Sci., 2012, 40(4), p 980-989.
X. Wu, H. Yan and Y. **n, Study on Microstructure and Properties of Laser Cladding Al-Ti-C Coating on Aluminum Alloy Surface, J. Nanoelectron. Optoelectron., 2018, 13(8), p 1258-1264.
Y. Cai, L. Zhen, C. Yao et al., Influence of CeO2 on Tribological Behaviour of TiC/Fe-Based Composite Coating, Surf. Eng., 2017, 33(12), p 936-943.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (Grant Nos. 52075542 and 52130509), and 145 Project.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Liu, M., Peng, Qq., Zhu, Xw. et al. Development of an Alternative to the Plasma Cladding Process: the Plasma Spray Melting Technology. J Therm Spray Tech 32, 1362–1377 (2023). https://doi.org/10.1007/s11666-023-01574-6
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11666-023-01574-6