Abstract
We report a new failure phenomenon during flip-chip die attach. After reflow, flip-chip bumps were separated between the Al and Ti layers on the Si die side. This was mainly observed at the Si die corner. Transmission electron microscopy images revealed corrosion of the Al layer at the edge of the solder bump metallization. The corrosion at the metallization edge exhibited a notch shape with high stress concentration factor. The organic substrate had Cu metallization with an organic solderable preservative (OSP) coating layer, where a small amount of Cl ions were detected. A solder bump separation mechanism is suggested based on the reaction between Al and Cl, related to the flow of soldering flux. During reflow, the flux will dissolve the Cl-containing OSP layer and flow up to the Al layer on the Si die side. Then, the Cl-dissolved flux will actively react with Al, forming AlCl3. During cooling, solder bumps at the Si die corner will separate through the location of Al corrosion. This demonstrated that the chemistry of the substrate metallization can affect the thermomechanical reliability of flip-chip solder joints.
Similar content being viewed by others
References
H.C. Lu, C.C. Kuo, P.A. Lin, C.-F. Tai, Y.-L. Chang, Y.-S. Jiang, J.-H. Tsai, Y.-M. Hsin, and H. Wang, IEEE Trans. Microw. Theory Technol. 60, 766 (2012).
B. Banijamali, I. Mohammed, and P. Savalia, 59th Electronic Components and Technology Conference, San Diego, 26–29 May 2009, pp. 293–300.
J. Sutanto, S. Anand, A. Sridharan, R. Korb, L. Zhou, M.S. Baker, M. Okandan, and J. Muthuswamy, J. Microelectromech. Syst. 21, 882 (2012).
R. Pendse, B.S. Choi, B. Kim, K.M. Kim, Y.C. Kim, K. Lee, S. Park, and D.W. Yang, 57th Electronic Components and Technology Conference, Reno, 29 June 1 2007, pp. 1425–1430.
K. Gilleo, Area Array Packaging Technology: Manufacturing and Assembly, Chap. 7 (New York: McGraw Hill, 2002).
H.M. Tong, Y.S. Lai, and C.P. Wong, Advanced Flip Chip Packaging, Chap. 10 (New York: Springer, 2013).
J.W. Jang, C.Y. Liu, P.G. Kim, K.N. Tu, A.K. Mal, and D.R. Frear, J. Mater. Res. 15, 1679 (2000).
S. Michaelides and S.K. Sitaraman, IEEE Trans. Adv. Packag. 22, 602 (1999).
J.W. Jang, L. Li, P. Bowles, R. Bonda, and D.R. Frear, Micrelectron. Reliab. 52, 455 (2012).
M.-C. Paquet, J. Sylvestre, E. Gros, and N. Boyer, 59th Electronic Components and Technology Conference, San Diego, 26–29 May 2009, pp. 960–965.
M. Joshi, R. Pendse, V. Pandey, T.K. Lee, I.S. Yoon, J.S. Yun, Y.C. Kim, and H.R. Lee, 60th Electronic Components and Technology Conference, Las Vegas, 1–4 June 2010, pp. 1250–1257.
D.C. Joy, A.D. Romig Jr., and J. Goldstein, Principles of Analytical Electron Microscopy, Chap. 4 (New York: Plenum, 1986).
H.-S. Lee and M.-S. Yi, J. Microelectron. Packag. Soc. 14, 1 (2007).
H. Holden and M. Carano, The PCB Magazine, June 2013, pp. 12–22.
Z. Szklarska-Smialowska, Corros. Sci. 41, 1743 (1999).
I. Barin, Thermochemical Data of Pure Substances, Part I (New York: VCH, 1989), p. 31.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Jang, J.W., Yoo, S.J., Hwang, H.I. et al. New Failure Mode of Flip-Chip Solder Joints Related to the Metallization of an Organic Substrate. J. Electron. Mater. 44, 3957–3961 (2015). https://doi.org/10.1007/s11664-015-3817-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11664-015-3817-2