Abstract
Steel parts are a kind of high recovery value product for which de-rusting is the primary step in the recycling process. Laser cleaning is a popular and effective de-rusting technique at present. However, the rust on most end-of-life/used parts is very serious, and it is difficult for laser cleaning to remove it all. Therefore, a compound cleaning method was proposed in which molten salt was first used for the pretreatment of rust, followed by laser cleaning. It was shown that the rust layer after pretreatment was much easier to remove with low laser fluence. The cleaning efficiency could be improved by at least 1.34 times, and a cleaner surface without any damage could be obtained. This was the result of the inner-to-outer cleaning effect of molten salt. The penetration into the rust layer and the decomposition of the doped organics caused the contaminant layer to be destroyed in the interior and then peeled off sheet by sheet. The composition and structure analysis indicated that the remaining rust layer was oxidized, and it became looser after molten salt cleaning, which made it easier to clean. The application of molten salt to the cleaning of rusty parts will improve de-rusting efficiency and promote the development of de-rusting techniques effectively. It provides a feasible and high-efficiency choice for de-rusting.
Graphic abstract
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Anonymous (1996) Laser tech shows promise in getting rid of rust. R&D Mag 38:11–11
Atanassova V, Kostadinov I, Penkova P (2019) Selective laser cleaning of corroded metal objects. In: AIP conference proceedings 2075 https://doi.org/10.1063/1.5091160
Ayodele TR, Alao MA, Ogunjuyigbe ASO (2018) Recyclable resources from municipal solid waste: assessment of its energy, economic and environmental benefits in Nigeria Resources. Conserv Recycl 134:165–173. https://doi.org/10.1016/j.resconrec.2018.03.017
Bennett P (2019) Rust Mater Today 30:103–104. https://doi.org/10.1016/j.mattod.2019.09.019
Chaves IA, Jeffrey R, Melchers RE (2015) Technical note: rust removal from steel coupons after short-term marine immersion. Corrosion (Houston, Tex) 71:811–818. https://doi.org/10.5006/1649
Chen GX, Kwee TJ, Tan KP, Choo YS, Hong MH (2010) Laser cleaning of steel for paint removal. Appl Phys Mater Sci Process 101:249–253
Daurelio G, Chita G, Cinquepalmi M (1999) Laser surface cleaning, de-rusting, de-painting and de-oxidizing. Appl Phys A Mater Sci Process 69:S543–S546. https://doi.org/10.1007/s003390051467
Durkee JB (2014) Cleaning with solvents: science and technology. In: John B. Durkee (ed). vol Book, Whole. Elsevier Science, Oxford
Guan YC, Ng GKL, Zheng HY, Hong MH, Hong X, Zhang Z (2013) Laser surface cleaning of carbonaceous deposits on diesel engine piston. Appl Surf Sci 270:526–530
Guo S, Si R, Dai Q, You Z, Ma Y, Wang J (2019) A critical review of corrosion development and rust removal techniques on the structural/environmental performance of corroded steel bridges. J Clean Prod 233:126–146. https://doi.org/10.1016/j.jclepro.2019.06.023
Hatcher GD, Ijomah WL, Windmill JFC (2011) Design for remanufacture: a literature review and future research needs. J Clean Prod 19:2004–2014
Inman D, Lovering DG (1981) Ionic liquids, vol Book, Whole. Springer, US, Boston, MA. https://doi.org/10.1007/978-1-4757-0920-9
Jiawei et al (2019) Influence of parameters of a laser cleaning soil rust layer on the surface of ceramic artifacts. Appl Opt 58:2725–2730
**an L, Yanhe S, Yuan F, Jun T, Chunyu F, Hua Z, Chengbing Z (2020) Mechanism research and equipment development of laser cleaning rust. J Phys Conf Ser 1453:012041 (012044 pp)
Ke L, Zhu H, Lei W, Cheng Z (2009) Laser cleaning of rust on ship steel using TEA CO2 pulsed laser. In: Photonics and optoelectronics meetings (POEM) 2009: industry lasers and applications
Li MZ et al (2016) Feasibility study of a new approach to removal of paint coatings in remanufacturing. J Mater Process Tech 234:102–112
Liu WW, Zhang B, Li YZ, He YM, Zhang HC (2014) An environmentally friendly approach for contaminants removal using supercritical CO2 for remanufacturing industry. Appl Surf Sci 292:142–48
Liu WW, Li MZ, Short T, Qing XC, Zhang HC (2015) Supercritical carbon dioxide cleaning of metal parts for remanufacturing industry. J Clean Prod 93:339–346
Long Y, Li J, Timmer DH, Jones RE, Gonzalez MA (2014) Modeling and optimization of the molten salt cleaning process. J Clean Prod 68:243–251
Matsumoto M, Yang S, Martinsen K, Kainuma Y (2016) Trends and research challenges in remanufacturing. Int J Precis Eng Manufacturing-Green Technol 3:129–142. https://doi.org/10.1007/s40684-016-0016-4
Monnier J, Dillmann P, Legrand L, Guillot I (2010) Corrosion of iron from heritage buildings: proposal for degradation indexes based on rust layer composition and electrochemical reactivity. Corros Eng Sci Technol 45:375–380. https://doi.org/10.1179/147842210X12779093813740
Morcillo M, Chico B, Díaz I, Cano H, Fuente DDL (2013) Atmospheric corrosion data of weathering steels. A Rev Corros Sci 77:6–24
Narayanan V, Singh RK, Marla D (2018) Laser cleaning for rust removal on mild steel: an experimental study on surface characteristics. In: Chen LH, Kondo Y (eds) ICDME 2018. EDP Sciences, 221: 1007. https://doi.org/10.1051/matecconf/201822101007
Raabe D, Tasan CC, Olivetti EA (2019) Strategies for improving the sustainability of structural metals. Nature 575:64–74. https://doi.org/10.1038/s41586-019-1702-5
Reijnders L (2016) Conserving functionality of relatively rare metals associated with steel life cycles: a review. J Clean Prod 131:76–96. https://doi.org/10.1016/j.jclepro.2016.05.073
Ren Z, Wu C, Chen H, Lu Y, Qiao H, Hu T (2017) Mechanism of laser derusting and surface properties of low carbon steel. Guangdian Gongcheng/Opto-Electron Eng 44:1210–1216. https://doi.org/10.3969/j.issn.1003-501X.2017.12.009
Riedewald F, Sousa-Gallagher M (2015) Novel waste printed circuit board recycling process with molten salt. MethodsX 2:100–106. https://doi.org/10.1016/j.mex.2015.02.010
Saji VS (2019) Progress in rust converters. Prog Org Coat 127:88–99. https://doi.org/10.1016/j.porgcoat.2018.11.013
Smith GC, Hopwood AB, Titchener KJ (2002) Microcharacterization of heavy-duty diesel engine piston deposits. Surf Interface Anal 33:259–268. https://doi.org/10.1002/sia.1209
Spile S, Suzuki T, Bendix J, Simonsen KP (2016) Effective cleaning of rust stained marble. Herit Sci 4:12
Usman M et al (2018) Magnetite and green rust: synthesis, properties, and environmental applications of mixed-valent iron minerals. Chem Rev 118:3251–3304. https://doi.org/10.1021/acs.chemrev.7b00224
Wang Z, Zeng X, Huang W (2003) Parameters and surface performance of laser removal of rust layer on A3 steel. Surf Coat Technol 166:10–16
Wang CS, Chen KK, Tajima K, Nagamatsu Y, Kakigawa H, Kozono Y (2010) Effects of sandblasting media and steam cleaning on bond strength of titanium-porcelain. Dent Mater J 29:381–391
Wang Z, Fang S, Zhu F, Wang W, Li Y, Chen T, Wang J (2019) Design of hull ultra high-pressure water ejector derusting system. IOP Conf Ser Earth Environ Sci 300:32016. https://doi.org/10.1088/1755-1315/300/3/032016
Watkins KG, Chen X, Fujioka T, Matsunawa A (2000) Mechanisms of laser cleaning. Proc SPIE Int Soc Opt Eng 3888:165–174
Witjes S, Lozano R (2016) Towards a more circular economy: proposing a framework linking sustainable public procurement and sustainable business models Resources. Conserv Recycl 112:37–44. https://doi.org/10.1016/j.resconrec.2016.04.015
Yao Z, Li J, Zhao X (2011) Molten salt oxidation: a versatile and promising technology for the destruction of organic-containing wastes. Chemosphere 84:1167–1174. https://doi.org/10.1016/j.chemosphere.2011.05.061
Acknowledgements
This work is supported by the Major Project on Science and Technology Innovation of Shandong Province (2018CXGC0807) and the National Natural Science Foundation of China (NSFC51875324).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
About this article
Cite this article
Wang, X., Li, J., Wang, L. et al. A novel de-rusting method with molten salt precleaning and laser cleaning for the recycling of steel parts. Clean Techn Environ Policy 23, 1403–1414 (2021). https://doi.org/10.1007/s10098-020-02023-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10098-020-02023-6