Abstract
The spreading behaviour of cohesive sand powder is modelled by Discrete Element Method, and the spreadability and the mechanical jamming are focused. The empty patches and total particle volume of the spread layer are examined, followed by the analysis of the geometry force and jamming structure. The results show that several empty patches with different size and shapes could be observed within the spread layer along the spreading direction even when the gap height increases to 3.0D90. Large particles are more difficult to be spread onto the base due to jamming, although their size is smaller than the gap height. Size segregation of particles occurs before particles entering the gap between the blade and base. There are almost no particles on the smooth base when the gap height is small, due to the full-slip flow of particles. The difference of the spread layer and spreadability between the cases with rough and smooth base is reduced by the increase of the gap height. An interesting correlation between jamming effect and local defects (empty spaces) in the powder layer is identified. The resistance to particle rolling is important for the mechanical jamming reported in this work. The jammed particles with a larger size ratio tend to be more stable.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Yang, B., Wang, Y., Zhang, Y.: The 3-D spread of saltation sand over a flat bed surface in aeolian sand transport. Adv. Powder Technol. 20, 303–309 (2009)
Upadhyay, M., Sivarupan, T., El Mansori, M.: 3D printing for rapid sand casting—A review. J. Manuf. Process. 29, 211–220 (2017)
Sivarupan, T., Balasubramani, N., Saxena, P., Nagarajan, D., El Mansori, M., Salonitis, K., Jolly, M., Dargusch, M.S.: A review on the progress and challenges of binder jet 3D printing of sand moulds for advanced casting. Additive Manuf., 40 (2021)
Nasato, D., Pöschel, T.: Influence of particle shape in additive manufacturing: Discrete element simulations of polyamide 11 and polyamide 12, 36 101421. (2020)
Schiochet Nasato, D., Briesen, H., Pöschel, T.: Influence of vibrating recoating mechanism for the deposition of powders in additive manufacturing: Discrete element simulations of polyamide 12. Additive Manuf. 48, 102248 (2021)
Yao, D., An, X., Fu, H., Zhang, H., Yang, X., Zou, Q., Dong, K.: Dynamic investigation on the powder spreading during selective laser melting additive manufacturing. Additive Manuf. 37, 101707 (2021)
Phua, A., Doblin, C., Owen, P., Davies, C.H.J., Delaney, G.W.: The effect of recoater geometry and speed on granular convection and size segregation in powder bed fusion. Powder Technol. 394, 632–644 (2021)
Ruggi, D., Lupo, M., Sofia, D., Barrès, C., Barletta, D., Poletto, M.: Flow properties of polymeric powders for selective laser sintering. Powder Technol. 370, 288–297 (2020)
Parteli, E.J.R., Poschel, T.: Particle-based simulation of powder application in additive manufacturing. Powder Technol. 288, 96–102 (2016)
Haeri, S., Wang, Y., Ghita, O., Sun, J.: Discrete element simulation and experimental study of powder spreading process in additive manufacturing. Powder Technol. 306, 45–54 (2016)
Haeri, S.: Optimisation of blade type spreaders for powder bed preparation in Additive Manufacturing using DEM simulations. Powder Technol. 321, 94–104 (2017)
Desai, P.S., Mehta, A., Dougherty, P.S.M., Higgs, C.F.: A rheometry based calibration of a first-order DEM model to generate virtual avatars of metal Additive Manufacturing (AM) powders. Powder Technol. 342, 441–456 (2019)
Chen, H., Wei, Q.S., Wen, S.F., Li, Z.W., Shi, Y.S.: Flow behavior of powder particles in layering process of selective laser melting: Numerical modeling and experimental verification based on discrete element method. Int. J. Mach. Tool. Manu. 123, 146–159 (2017)
Nan, W., Pasha, M., Tina, B., Alejandro, L., Umair, Z., Sadegh, N., Ghadiri, M.: Jamming during particle spreading in additive manufacturing. Powder Technol. 338, 253–262 (2018)
Ghadiri, M., Pasha, M., Nan, W., Hare, C., Vivacqua, V., Zafar, U., Nezamabadi, S., Lopez, A., Pasha, M., Nadimi, S.: Cohesive powder Flow: Trends and challenges in Characterisation and Analysis. Kona Powder Part. J. 37, 3–18 (2020)
Snow, Z., Martukanitz, R., Joshi, S.: On the development of powder spreadability metrics and feedstock requirements for powder bed fusion additive manufacturing. Additive Manuf. 28, 78–86 (2019)
Nan, W., Gu, Y.: Experimental investigation on the spreadability of cohesive and frictional powder. Adv. Powder Technol. 33, 103466 (2022)
Lupo, M., Ajabshir, S.Z., Sofia, D., Barletta, D., Poletto, M.: Experimental metrics of the powder layer quality in the selective laser sintering process. Powder Technol. 419, 118346 (2023)
Shaheen, M.Y., Thornton, A.R., Luding, S., Weinhart, T.: The influence of material and process parameters on powder spreading in additive manufacturing. Powder Technol. 383, 564–583 (2021)
Xu, R., Nan, W.: Analysis of the metrics and mechanism of powder spreadability in powder-based additive manufacturing. Additive Manuf., 71 (2023)
Nan, W., Ge, L., Xuan, W., Gu, Y.: Transient jamming of granular flow by blade spreading. Powder Technol., 431 (2024)
Nan, W., Rahman, M.A., Ge, L., Sun, Z.: Effect of plastic deformation on the spreadability of cohesive powder in the spreading process. Powder Technol., 425 (2023)
Cundall, P.A., Strack, O.D.L.: A discrete numerical model for granular assemblies. Geotechnique. 29, 47–65 (1979)
Thornton, C., Dynamics, G.: Contact Mechanics and Particle System Simulations: A DEM Study, (2015)
Johnson, K.L., Kendall, K., Roberts, A.D., Tabor, D.: Surface energy and the contact of elastic solids. Proc. Royal Soc. Lond. Math. Phys. Sci. 324, 301–313 (1971)
Ai, J., Chen, J.-F., Rotter, J.M., Ooi, J.Y.: Assessment of rolling resistance models in discrete element simulations. Powder Technol. 206, 269–282 (2011)
Schindelin, J., Arganda-Carreras, I., Frise, E., Kaynig, V., Longair, M., Pietzsch, T., Preibisch, S., Rueden, C., Saalfeld, S., Schmid, B., Tinevez, J.Y., White, D.J., Hartenstein, V., Eliceiri, K., Tomancak, P., Cardona, A.: Fiji: An open-source platform for biological-image analysis. Nat. Methods. 9, 676–682 (2012)
Acknowledgements
The authors are grateful to the National Key Research and Development Program of China (Grant No. 2022YFB4602202) and National Natural Science Foundation of China (Grant No. 51806099). The second author is also thankful to Postgraduate Research & Practice Innovation Program of Jiangsu Province (Grant No. KYCX23_1440). The corresponding author is also thankful to Professor Mojtaba Ghadiri, University of Leeds, UK, for the inspiration on this work.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest that could have appeared to influence the work reported in this paper.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Xu, Y., Ge, L. & Nan, W. Investigation on the spreading behaviour of sand powder used in binder jet 3D printing. Granular Matter 26, 49 (2024). https://doi.org/10.1007/s10035-024-01420-8
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10035-024-01420-8