Abstract
The aim of this work is to study the influence of milling parameters on tool wear, surface residual stress, and corrosion resistance of a UNS S32750 super duplex stainless steel. Face milling tests were carried out varying cutting speed and feed rate both in two levels. Tool wear was monitored until they obtained flank wear values of 0.3 mm and after the tools reached maximum wear, they were analyzed by scanning electron microscopy to identify the wear phenomena. The machining conditions were repeated on new specimens that were subjected to residual stress tests by the blind hole drilling method and corrosion by potentiodynamic polarization. The main results obtained was that the predominant tool wear were flank and notch wear, with predominant wear mechanisms of adhesion and abrasion; lower cutting speeds and feeds provided a greater volume of removed material; when cutting using lower cutting speed, a decrease of 30% on feed per tooth generated an increase about 20% on tool life; the lower cutting conditions yields higher compressive stresses; with the lowest cutting speed and lowest feed, the compressive stress was 800 MPa; while in the highest feed and speed condition, we obtained a tensile stress of 30 MPa; and in the conditions tested, the variation of any cutting parameter did not have a significant influence on the corrosion resistance of the part. Summarizing, the lowest cutting speed at the lowest feed provided superior quality in terms of tool life, surface residual stress, and corrosion resistance for milling UNS S32750 steel.
Similar content being viewed by others
References
Gunn RN (1997) 1 - Developments, grades and specifications. In: Woodhead Publishing Series in Metals and Surface Engineering, Duplex Stainless Steels. Woodhead Publishing, pp 1–13. https://doi.org/10.1533/9781845698775.1
Nilsson JO (1992) Super duplex stainless steels. Mater Sci Technol 8(8):685–700. https://doi.org/10.1179/mst.1992.8.8.685
Davison RM, Redmond JD (1991) A guide to using duplex stainless steels. Mater Des 12(4):187–192. https://doi.org/10.1016/0261-3069(91)90162-W. (ISSN 0261-3069)
IMOA (2014) Practical guidelines for the fabrication of duplex stainless steel, 3rd edn. International Molybdenum Association, London, UK
Salvetr P, Školáková A, Melzer D, Brázda M, Duchoň J, Drahokoupil J, Svora P, Msallamová S, Novák P (2022) Characterization of super duplex stainless steel SAF2507 deposited by directed energy deposition. Mater Sci Eng: A 857:144084. https://doi.org/10.1016/j.msea.2022.144084. (ISSN 0921-5093)
Wu X-H, Song Z-G, Liu L-Z, He J-G, Zheng L (2022) Effect of secondary austenite on fatigue behavior of S32750 super duplex stainless steel. Mater Lett 322:132487. https://doi.org/10.1016/j.matlet.2022.132487. (ISSN 0167-577X)
Amiri E, Ostovan F, Toozandehjani M, Shafiei E, Mohamed IF (2021) Study and selection of most appropriate filler rod for GTAW of S32750 super duplex steel joints: a comprehensive study on microstructural, mechanical and corrosion properties. Mater Chem Phys 270:124839. https://doi.org/10.1016/j.matchemphys.2021.124839. (ISSN 0254-0584)
Ha H-Y, Jang M-H, Lee T-H, Moon J (2015) Understanding the relation between phase fraction and pitting corrosion resistance of UNS S32750 stainless steel. Mater Char 106:338–345. https://doi.org/10.1016/j.matchar.2015.06.019
Garfias-Mesias LF, Sykes JM, Tuck CDS (1996) The effect of phase compositions on the pitting corrosion of 25 Cr duplex stainless steel in chloride solutions. Corros Sci 38(8):1319–1330. https://doi.org/10.1016/0010-938x(96)00022-4
Ha H-Y, Jang M-H, Lee T-H, Moon J (2014) Interpretation of the relation between ferrite fraction and pitting corrosion resistance of commercial 2205 duplex stainless steel. Corros Sci 89:154–162. https://doi.org/10.1016/j.corsci.2014.08.021
Ha H-Y, Lee T-H, Lee C-G, Yoon H (2019) Understanding the relation between pitting corrosion resistance and phase fraction of S32101 duplex stainless steel. Corros Sci. https://doi.org/10.1016/j.corsci.2019.01.001
Zhou Y, Engelberg DL (2022) Application of bipolar electrochemistry to assess the ambient temperature corrosion resistance of solution annealed type 2205 duplex stainless steel. Mater Chem Phys 275:125183. https://doi.org/10.1016/j.matchemphys.2021.125183. (ISSN 0254-0584)
Assis KSA, Sousa FVV, Miranda M, Margarit-Mattos ICP, Vivier V, Mattos OR (2012) Assessment of electrochemical methods used on corrosion of superduplex stainless steel. Corros Sci 59:71–80. https://doi.org/10.1016/j.corsci.2012.02.014. (ISSN 0010-938X)
Örnek C, Ahmed A, Engelberg D (2012) Effect of microstructure on atmospheric-induced corrosion of heat-treated grade 2205 and 2507 duplex stainless steels. Eurocorr 2012, Istanbul. https://doi.org/10.13140/RG.2.1.3765.3607
Silva RCC, Nogueira RP, Bastos IN (2011) Tribocorrosion of UNS S32750 in chloride medium: effect of the load level. Electrochim Acta 56(24):8839–8845. https://doi.org/10.1016/j.electacta.2011.07.077. (ISSN 0013-4686)
Gowthaman PS, Jeyakumar S, Saravanan BA (2020) Machinability and tool wear mechanism of duplex stainless steel – a review. Mater Today: Proc 26(Part 2):1423–1429. https://doi.org/10.1016/j.matpr.2020.02.295. (ISSN 2214-7853)
Nomani J, Pramanik A, Hilditch T, Littlefair G (2013) Machinability study of first generation duplex (2205), second generation duplex (2507) and austenite stainless steel during drilling process. Wear 304(1–2):20–28. https://doi.org/10.1016/j.wear.2013.04.008
Gunn RN (1997) 4 - Forming and machining. In: Woodhead Publishing Series in Metals and Surface Engineering, Duplex Stainless Steels. Woodhead Publishing, pp 50–55. https://doi.org/10.1533/9781845698775.50
Arun KK, Navaneeth VR, Prabhu S, Kumar MR, Giriraj M (2022) Experimental investigation of turning process parameter under several cutting conditions for duplex steels for minimization of cutting temperature. Mater Today: Proc 62(Part 4):1917–1920. https://doi.org/10.1016/j.matpr.2022.01.447. (ISSN 2214-7853)
George O, Leo Dev Wins K, Ebenezer Jacob Dhas DS, George P, Beatrice B A (2021) Machinability, weldability and surface treatment studies of SDSS 2507 material-a review. Mater Today: Proc 46(Part 17):7682–7687. https://doi.org/10.1016/j.matpr.2021.02.089
George P, Wins KLD, Dhas DSEJ, George P, Beatrice BA (2021) Effect of machining parameters on cutting force during dry milling of 2205 DSS and 2507 SDSS materials. Mater Today: Proc 47(Part 19):6614–6617. https://doi.org/10.1016/j.matpr.2021.05.097. (ISSN 2214-7853)
Liu CR, Barash MM (1982) Variables governing patterns of mechanical residual stress in a machined surface. ASME J Eng Ind 104(3):257–264. https://doi.org/10.1115/1.3185828
Saı̈ WB, Salah NB, Lebrun JL (2001) Influence of machining by finishing milling on surface characteristics. Int J Mach Tools Manuf 41(3):443–450. https://doi.org/10.1016/S0890-6955(00)00069-9. (ISSN 0890-6955)
SAE (2003) Residual stress measurement by x-ray diffraction: HS-784. Society of Automotive Engineers, Warrendale, PA
Huang K, Yang W (2017) Analytical analysis of the mechanism of effects of machining parameter and tool parameter on residual stress based on multivariable decoupling method. Int J Mech Sci. https://doi.org/10.1016/j.ijmecsci.2017.05.031
Lyon KN, Marrow TJ, Lyon SB (2015) Influence of milling on the development of stress corrosion cracks in austenitic stainless steel. J Mater Process Technol 218:32–37. https://doi.org/10.1016/j.jmatprotec.2014.11.038
Saoubi R, Outeiro JC, Changeux B, Lebrun JL, Morão Dias A (1999) Residual stress analysis in orthogonal machining of standard and resulfurized AISI 316L steels. J Mater Process Technol 96(1–3):225–233. https://doi.org/10.1016/S0924-0136(99)00359-3. (ISSN 0924-0136)
Dumas M, Valiorgue F, Van Robaeys A, Rech J (2018) Interaction between a roughing and a finishing operation on the final surface integrity in turning. Procedia CIRP 71:396–400. https://doi.org/10.1016/j.procir.2018.05.050. (ISSN 2212-8271)
Hassiotis ND, Petropoulos GP (2006) Influence of surface roughness on corrosion resistance of turned carbon steel parts. Int J Mach Mach Mater 1(2):202–212
Hassiotis N, Petropoulos G, Hatzopoulos C, Vaxevanidis N (2007) Influence of surface topography on corrosion of stainless steel AISI 304 turned surfaces with different cutting conditions. In Adv Mater Res 18:399–405 (Trans Tech Publications Ltd)
Korkut I, Kasap M, Ciftci I, Seker U (2004) Determination of optimum cutting parameters during machining of AISI 304 austenitic stainless steel. Mater Des 25(4):303–305. https://doi.org/10.1016/j.matdes.2003.10.011. (ISSN 0261-3069)
Ciftci I (2006) Machining of austenitic stainless steels using CVD multi-layer coated cemented carbide tools. Tribol Int 39(6):565–569. https://doi.org/10.1016/j.triboint.2005.05.005. (ISSN 0301-679X)
Oliveira Junior CA, Diniz AE, Bertazzoli R (2014) Correlating tool wear, surface roughness and corrosion resistance in the turning process of super duplex stainless steel. J Braz Soc Mech Sci Eng 36:775–785. https://doi.org/10.1007/s40430-013-0119-6
Ramkumar KD, Goutham PS, Radhakrishna VS, Tiwari A, Anirudh S (2016) Studies on the structure–property relationships and corrosion behaviour of the activated flux TIG welding of UNS S32750. J Manuf Process 23:231–241. https://doi.org/10.1016/j.jmapro.2016.05.006. (ISSN 1526-6125)
Author information
Authors and Affiliations
Contributions
All authors contributed to the study conception and design. Material preparation, data collection, and analysis were performed by Daniel Cirillo Marques and corrosion tests were performed by Daniel Cirillo Marques and Renato Altobelli Antunes. The first draft of the manuscript was written by Daniel Cirillo Marques and all authors commented on previous versions of the manuscript. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Marques, D.C., Suyama, D.I., Antunes, R.A. et al. Influence of machining parameters on tool wear, residual stresses, and corrosion resistance after milling super duplex stainless steel UNS S32750. Int J Adv Manuf Technol 129, 801–814 (2023). https://doi.org/10.1007/s00170-023-12328-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-023-12328-7