Abstract
For realizing ultrasonic elliptical vibration-assisted cutting, a single excitation elliptical vibration system was proposed in this work, which was composed of a giant magnetostrictive transducer and an asymmetrical stepped ultrasonic horn with arc transition (ASUH). The dynamic simulation of the vibration system was carried out using ANSYS, the output end of the vibration system produced longitudinal and transverse vibrations simultaneously due to the ASUH at the resonant frequency, and the influence of the transition arc of the ASUH on the elliptical vibration performance of the vibration system was studied. The impedance, elliptical vibration trajectory of the output end, and output amplitude of the vibration system were tested experimentally. The results show that the actual resonant frequency of the vibration system was 20.708 kHz, the mechanical quality factor was 106, and the longitudinal amplitude was slightly greater than the transverse amplitude of the output end. The theoretical calculations coincide with the experimentally tested results.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Saito H, Jung H, Shamoto E (2016) Elliptical vibration cutting of hardened die steel with coated carbide tools. Precis Eng 45:44–54. https://doi.org/10.1016/j.precisioneng.2016.01.004
Ma C, Shamoto E, Moriwaki T, Wang L (2004) Study of machining accuracy in ultrasonic elliptical vibration cutting. Int J Mach Tool Manu 44(12-13):1305–1310. https://doi.org/10.1016/j.ijmachtools.2004.04.014
Ma C, Shamoto E, Moriwaki T, Zhang Y, Wang L (2005) Suppression of burrs in turning with ultrasonic elliptical vibration cutting. Int J Mach Tool Manu 45(11):1295–1300. https://doi.org/10.1016/j.ijmachtools.2005.01.011
Ma C, Ma J, Shamoto E, Moriwaki T (2011) Analysis of regenerative chatter suppression with adding the ultrasonic elliptical vibration on the cutting tool. Precis Eng 35(2):329–338. https://doi.org/10.1016/j.precisioneng.2010.12.004
Shamoto E, Moriwaki T (1999) Ultraprecision diamond cutting of hardened steel by applying elliptical vibration cutting. CIRP Ann 48(1):441–444. https://doi.org/10.1016/S0007-8506(07)63222-3
Zhang C, Ehmann K, Li Y (2015) Analysis of cutting forces in the ultrasonic elliptical vibration-assisted micro-groove turning process. Int J Adv Manuf Tech 78(1-4):139–152. https://doi.org/10.1007/S00170-014-6628-3
Tan R, Zhao X, Sun T, Zou X, Hu Z (2019) Experimental investigation on micro-groove manufacturing of Ti-6Al-4V alloy by using ultrasonic elliptical vibration assisted cutting. Materials 12(19):3086. https://doi.org/10.3390/ma12193086
Gao J, Altintas Y (2019) Development of a three-degree-of-freedom ultrasonic vibration tool holder for milling and drilling. IEEE-ASME T Mech 24(3):1238–1247. https://doi.org/10.1109/TMECH.2019.2906904
Liu Q, Li Q, Chen Z, Li Y, Zhou X, Wang R, Xu P (2022) Study on abrasive belt grinding process assisted by ultrasonic elliptic vibration. Int J Adv Manuf Tech 120(7-8):4647–4661. https://doi.org/10.1007/s00170-022-09027-0
Wang L, Guan Y, Liu Y, Jie D, Liu J (2021) A compact cantilever-type ultrasonic motor with nanometer resolution: design and performance evaluation. IEEE Trans Ind Electron 68(1):734–743. https://doi.org/10.1109/TIE.2020.2965481
Zhou M, Hu L (2015) Development of an innovative device for ultrasonic elliptical vibration cutting. Ultrasonics 60:76–81. https://doi.org/10.1016/j.ultras.2015.02.015
Kurniawan R, Ko T, Kumaran S, Ahmed F (2021) 3-DOF ultrasonic elliptical vibration tool holder based on coupled resonance modes for manufacturing micro-groove. Precis Eng 67:212–231. https://doi.org/10.1016/j.precisioneng.2020.10.002
Yin S, Bao Y, Pan Y, Dong Z, ** Z, Kang R (2022) Development of ultrasonic elliptical vibration cutting device with multi-stage amplification function. J Mech Eng Chin Ed 58(11):260–268. https://doi.org/10.3901/JME.2022.11.260
Zhang C, Lu M (2018) A novel variable-dimensional vibration-assisted actuator for drilling CFRP. Int J Adv Manuf Tech 99:3049–3063. https://doi.org/10.1007/s00170-018-2680-8
Bai W, Wang K, Du D, Zhang J, Huan W, Xu J (2022) Design of an ultrasonic elliptical vibration device with two stationary points for ultra-precision cutting. Ultrasonics 120:106662. https://doi.org/10.1016/j.ultras.2021.106662
Li X, Zhang D (2006) Ultrasonic elliptical vibration transducer driven by single actuator and its application in precision cutting. J Mater Process Tech 180(1-3):91–95. https://doi.org/10.1016/j.jmatprotec.2006.05.007
Yin Z, Fu Y, Li H, Cao Z, Chen Y (2017) Mathematical modeling and experimental verification of a novel single-actuated ultrasonic elliptical vibrator. Adv Mech Eng 9(12):1–12. https://doi.org/10.1177/1687814017745413
Li P, Liu Q, Li S, Wang Q, Zhang D, Li Y (2017) Design and numerical simulation of novel giant magnetostrictive ultrasonic transducer. Results Phys 7:3946–3954. https://doi.org/10.1016/j.rinp.2017.10.010
Zhou G, Li M (2000) A study on ultrasonic solid horns for flexural mode. J Acoust Am 107(3):1358–1362. https://doi.org/10.1121/1.428423
He X (2006) Rare earth giant magnetostrictive transducer. Science Press, Bei**g
Li P, Liu Q, Zhou X, Xu G, Li W, Wang Q, Yang M (2020) Effect of Terfenol-D rod structure on vibration performance of giant magnetostrictive ultrasonic transducer. J Vib Control. 27(5-6):573–581. https://doi.org/10.1177/1077546320932029
Mo X, Zhu H, Liu J, Cui Z (2000) Terfenol-D giant magnetostrictive transducer simulation by finite element method. Appl Acoust 19(4):5–8. https://doi.org/10.11684/j.issn.1000-310X.2000.04.003
Funding
This work was supported by the National Natural Science Foundation of China (No. 12174241) and the Fundamental Research Funds for the Central Universities (No. 2020TS024).
Author information
Authors and Affiliations
Contributions
**** He: writing — review and editing, supervision, validation, funding acquisition, resources. Qiang Liu: writing — original draft, methodology, formal analysis, visualization.
