Abstract
The residual compressive stress on the surface of the gear after the power honing process could significantly improve the service performance and life of the gear. In order to study the formation mechanism and special distribution of the residual stress, a spiral scratching experiment is designed for the gear steel samples. Meanwhile, the influence of preload force and groove spacing on the residual stress is studied. The result shows that the residual stress increases from − 252 MPa to − 344 MPa in the parallel feed direction and from − 317 MPa to − 541 MPa in the vertical direction as the spacing decreases. With the increase of preload force, the residual stress value decreases when the spacing is small and increases when the spacing is large. Then, the three-dimensional finite element model of double abrasive grains is established with ABAQUS. The residual stress value of the whole surface is distilled and compared with the experimental one. According to the experimental and simulation results, the residual compressive stress of power honing is mainly caused by plastic deformation and the reason for its special distribution is that a smaller scratch spacing is generated in the area of the pitch line of tooth surface.
Similar content being viewed by others
Data availability
All authors confirm that the data supporting the findings of this study are available within the article.
Code availability
Not applicable.
References
Karpuschewski B, Beutner M, Eckebrecht J, Heinzel J, Hüsemannab T (2020) Surface integrity aspects in gear manufacturing. Procedia CIRP 87(C):3–12. https://doi.org/10.1016/j.procir.2020.05.112
Han J, Zhu YG, **a L, Tian XQ (2018) A novel gear flank modification methodology on internal gearing power honing gear machine. Mech Mach Theory 121:669–682. https://doi.org/10.1016/j.mechmachtheory.2017.11.024
Fan ZH, Tian YB, Liu ZQ, Shi C, Zhao YG (2019) Investigation of a novel finishing tool in magnetic field assisted finishing for titanium alloy Ti-6Al-4V. J Manuf Process 43:74–82. https://doi.org/10.1016/j.jmapro.2019.05.007
Zhang WQ, Wei XQ, Guo XD, Tan RL, Wang YW (2022) A novel continuous indexing method for face-hobbed hypoid gear tooth grinding. Mech Mach Theory 173:104826. https://doi.org/10.1016/j.mechmachtheory.2022.104826
Zhao B, Guo XC, Bie WB, Chang BQ, Zhao CY (2020) Thermo-mechanical coupling effect on surface residual stress during ultrasonic vibration-assisted forming grinding gear. J Manuf Process 59:19–32. https://doi.org/10.1016/j.jmapro.2020.09.041
Ren Q, **a L, Zhang GZ, Zhu YG, Han J (2020) Prediction of surface roughness of workpiece for internal gearing power honing process and variation analysis. J Mech Trans 44, 279(03):15–19. https://doi.org/10.16578/j.issn.1004.2539.2020.03.002
Han J, Yuan B, Wang D, Sun CH, **a L (2017) Formation mechanism study on tooth surface of two gear finishing processes: combined theoretical and experimental approaches. J Braz Soc Mech Sci Eng 39:5159–5170. https://doi.org/10.1007/s40430-017-0872-z
Han J, Zhang G (2018) Investigation on formation mechanism of surface texture and modeling of surface roughness with internal gear power honing. Int J Adv Manuf Technol 98:603–615. https://doi.org/10.1007/s00170-018-2265-6
Hu ZX, **a L, Han J (2021) Study on surface residual stress of internal meshing strong honing workpiece. J Hefei Univ Technol (Nat Sci Ed) 44(01):31–36 ((in Chinese))
Liang Y (2020) Research and test on honing quality of hardened gear. Dissertation, Ningxia University, Ningxia, China.
Tran VQ, Wu YR (2020) A novel method for closed-loop topology modification of helical gears using internal-meshing gear honing. Mech Mach Theory 145(C): 103691. https://doi.org/10.1016/j.mechmachtheory.2019.103691
Yu B (2020) Influence of elastic deformation of gear hone teeth on machined gear accuracy. IOP Conf Ser Mater Sci Eng 971(4):042014. https://doi.org/10.1088/1757-899X/971/4/042014
Liao Z, Monaca AL, Murray J, Speidel A, Ushmaev D, Clare A, Axinte D, M’Saoubi R (2020) Surface integrity in metal machining - part I: fundamentals of surface characteristics and formation mechanisms. Int J Mach Tools Manuf 162:103687. https://doi.org/10.1016/j.ijmachtools.2020.103687
Brinksmeier E, Schneider C (1997) Grinding at very low speeds. CIRP Ann Manuf Technol 46(1):223–226. https://doi.org/10.1016/S0007-8506(07)60813-0
Karpuschewski B, Knoche HJ, Hipke M (2008) Gear finishing by abrasive processes. CIRP Ann Manuf Technol 57(2):621–640. https://doi.org/10.1016/j.cirp.2008.09.002
Zhao RS, Deng ZH, Liu W, Li CY (2020) Research progress of single abrasive grinding experiment and its numerical simulation. Aero Mater Technol 50(05):1–7. https://doi.org/10.12044/j.issn.1007-2330.2020.05.001
Zhou K, Liu J, **ao G, Huang Y, Song KK, Xu JY, Chen BQ (2021) Probing residual stress evolution of titanium alloy due to belt grinding based on molecular dynamics method. J Manuf Process 66:446–459. https://doi.org/10.1016/j.jmapro.2021.04.043
Wen J, Tang JY, Zhou WH (2021) Study on formation mechanism and regularity of residual stress in ultrasonic vibration grinding of high strength alloy steel. J Manuf Process 66:608–622. https://doi.org/10.1016/j.jmapro.2021.04.040
David C, Holger K, Andrew W, Donka N (2020) Impact of grinding wheel specification on surface integrity and residual stress when grinding Inconel 718. Proc Inst Mech Eng B J Eng Manuf 235:1668–1681. https://doi.org/10.1177/0954405420961209
Zhang YX, Yang X, Yuan SS, Zhu JH, Wang D (2021) Residual stress in high speed cylindrical grinding of 18crnimo7-6 steel. China Mechanical Engineering 32(05):540–546. https://doi.org/10.3969/j.issn.1004-132X.2021.05.005
Wu ZH, Zhang LC, Yang SY (2021) Effect of abrasive grain position patterns on the deformation of 6H-silicon carbide subjected to nano-grinding. Int J Mech Sci 211:106779. https://doi.org/10.1016/j.ijmecsci.2021.106779
Yu S, Wen J, Tang JY (2020) Calculation and experimental verification of residual stress on tooth surface of spur gear form grinding. J Mech Trans 44 (05):73–77 + 97. https://doi.org/10.16578/j.issn.1004.2539.2020.05.011
Mayer JE, Price AH, Purushothaman GK, Dhayalan AK, Pepi MS (2002) Specific grinding energy causing thermal damage in helicopter gear steel. J Manuf Process 4(2):142–147. https://doi.org/10.1016/S1526-6125(02)70140-0
Liu G, Yan H (2010) Experimental study on static and dynamic mechanical behavior of 20CrMnTi gear steel. Int Conf Measuring Technol Mechatron Auto. IEEE pp 191–195. https://doi.org/10.1109/ICMTMA.2010.187
Shu C, Cheng L, Xu Y (2020) Study on parameter estimation of Johnson cook constitutive model. Chinese J Nonferrous Metals 30(05):1073–1083
Sun J, Qu ZX, Zhang LW (2017) Simulation of TC11 single particle abrasive belt grinding process based on ABAQUS. Aeros Manuf Technol 06:21–25
Wang Z, Ma DY, Suo T, Li YL, Manesa A (2021) Investigation into different numerical methods in predicting the response of aluminosilicate glass under quasi-static and impact loading conditions. Int J Mech Sci 196:106286. https://doi.org/10.1016/j.ijmecsci.2021.106286
Wang JB, Ding J, Song X, Huang X, Zhang XD, Wang LS (2019) Study on dynamic stress response of 20CrMnTi steel under impact load and modified J-C constitutive model considering adiabatic temperature rise. J Mech Strength 41(05):1066–1070. https://doi.org/10.16579/j.issn.1001.9669.2019.05.009
Wang L, Tian XL, Lu Q, Li YD (2017) Material removal characteristics of 20CrMnTi steel in single grit cutting. Mater Manuf Process 32(13):1528–1536. https://doi.org/10.1080/10426914.2017.1279298
Yan L, Rong YM, Jiang F, Zhou ZX (2010) Three-dimension surface characterization of grinding wheel using white light interferometer. Int J Adv Manuf Technol 55:133–141. https://doi.org/10.1007/s00170-010-3054-z
Zhao CY, Li JY, Fan WG, Liu YM, Wang WX (2020) Experimental and simulation research on residual stress for abrasive belt rail grinding. Int J Adv Manuf Technol 109(10):129–142. https://doi.org/10.1007/s00170-020-05664-5
Wang WX, Li JY, Wu Y, Fan WG (2020) Experimental and simulation study on residual stress of rail abrasive belt grinding. Diamond Abrasives Eng 40(03):5–12 ((in Chinese))
Funding
This work is funded by Key Projects of Strategic Scientific and Technological Innovation Cooperation of National Key Research and Development Program of China (Grant 2020YFE0201000).
Author information
Authors and Affiliations
Contributions
Jiacheng Wang: investigation, methodology, numerical simulation, writing—original draft. Huajun Cao: supervision, project administration, writing—review and editing. Yuhu Liu: assistant for experiment, checking. **aohui Huang: materials and equipment support.
Corresponding author
Ethics declarations
Ethics approval
The manuscript has not been submitted to any other journal for simultaneous consideration. The submitted work is original and has not been published elsewhere in any form or language.
Consent to participate
All authors voluntarily agree to participate in this research study.
Consent for publication
All authors voluntarily agree to publish in this research study.
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Appendix
Appendix
In order to determine the relationship between the scratch width and the preload force in the experiment, a single scratch was scored using the same condition as the experiment, and a single scratch was performed at preload forces of 0.5 N, 1 N, 2 N, 3 N, and 4 N. The width of the scored scratch was subsequently measured using a super deep scene 3D microscope (VHX-1000, KEYENCE, Japan) and the depth of single groove was calculated. The result showed that the depth of grooves under force of 0.5 N, 1 N, 2 N, and 4 N was 13, 22.5, 32, and 41.5 μm respectively.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Wang, J., Cao, H., Liu, Y. et al. Simulation and experimental research on residual stress of honed gear based on scratch test. Int J Adv Manuf Technol 123, 985–998 (2022). https://doi.org/10.1007/s00170-022-10096-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-022-10096-4